/dts-v1/;
#include "skeleton.dtsi"
#include <dt-bindings/clock/qcom,gcc-msm8960.h>
#include <dt-bindings/reset/qcom,gcc-msm8960.h>
#include <dt-bindings/clock/qcom,mmcc-msm8960.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
model = "Qualcomm APQ8064";
compatible = "qcom,apq8064";
interrupt-parent = <&intc>;
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
smem_region: smem@80000000 {
reg = <0x80000000 0x200000>;
no-map;
};
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <0>;
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
cpu-idle-states = <&CPU_SPC>;
};
cpu@1 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <1>;
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
cpu-idle-states = <&CPU_SPC>;
};
cpu@2 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <2>;
next-level-cache = <&L2>;
qcom,acc = <&acc2>;
qcom,saw = <&saw2>;
cpu-idle-states = <&CPU_SPC>;
};
cpu@3 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <3>;
next-level-cache = <&L2>;
qcom,acc = <&acc3>;
qcom,saw = <&saw3>;
cpu-idle-states = <&CPU_SPC>;
};
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
};
idle-states {
CPU_SPC: spc {
compatible = "qcom,idle-state-spc",
"arm,idle-state";
entry-latency-us = <400>;
exit-latency-us = <900>;
min-residency-us = <3000>;
};
};
};
cpu-pmu {
compatible = "qcom,krait-pmu";
interrupts = <1 10 0x304>;
};
clocks {
cxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
};
pxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <27000000>;
};
sleep_clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
};
};
sfpb_mutex: hwmutex {
compatible = "qcom,sfpb-mutex";
syscon = <&sfpb_wrapper_mutex 0x604 0x4>;
#hwlock-cells = <1>;
};
smem {
compatible = "qcom,smem";
memory-region = <&smem_region>;
hwlocks = <&sfpb_mutex 3>;
};
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
ranges;
compatible = "simple-bus";
tlmm_pinmux: pinctrl@800000 {
compatible = "qcom,apq8064-pinctrl";
reg = <0x800000 0x4000>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&ps_hold>;
sdc4_gpios: sdc4-gpios {
pios {
pins = "gpio63", "gpio64", "gpio65", "gpio66", "gpio67", "gpio68";
function = "sdc4";
};
};
ps_hold: ps_hold {
mux {
pins = "gpio78";
function = "ps_hold";
};
};
i2c1_pins: i2c1 {
mux {
pins = "gpio20", "gpio21";
function = "gsbi1";
};
};
i2c3_pins: i2c3 {
mux {
pins = "gpio8", "gpio9";
function = "gsbi3";
};
};
gsbi6_uart_2pins: gsbi6_uart_2pins {
mux {
pins = "gpio14", "gpio15";
function = "gsbi6";
};
};
gsbi6_uart_4pins: gsbi6_uart_4pins {
mux {
pins = "gpio14", "gpio15", "gpio16", "gpio17";
function = "gsbi6";
};
};
gsbi7_uart_2pins: gsbi7_uart_2pins {
mux {
pins = "gpio82", "gpio83";
function = "gsbi7";
};
};
gsbi7_uart_4pins: gsbi7_uart_4pins {
mux {
pins = "gpio82", "gpio83", "gpio84", "gpio85";
function = "gsbi7";
};
};
};
sfpb_wrapper_mutex: syscon@1200000 {
compatible = "syscon";
reg = <0x01200000 0x8000>;
};
intc: interrupt-controller@2000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x02000000 0x1000>,
<0x02002000 0x1000>;
};
timer@200a000 {
compatible = "qcom,kpss-timer", "qcom,msm-timer";
interrupts = <1 1 0x301>,
<1 2 0x301>,
<1 3 0x301>;
reg = <0x0200a000 0x100>;
clock-frequency = <27000000>,
<32768>;
cpu-offset = <0x80000>;
};
acc0: clock-controller@2088000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
};
acc1: clock-controller@2098000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
};
acc2: clock-controller@20a8000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
};
acc3: clock-controller@20b8000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
};
saw0: power-controller@2089000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw1: power-controller@2099000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw2: power-controller@20a9000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw3: power-controller@20b9000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
gsbi1: gsbi@12440000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <1>;
reg = <0x12440000 0x100>;
clocks = <&gcc GSBI1_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
i2c1: i2c@12460000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c1_pins>;
pinctrl-names = "default";
reg = <0x12460000 0x1000>;
interrupts = <0 194 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi2: gsbi@12480000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <2>;
reg = <0x12480000 0x100>;
clocks = <&gcc GSBI2_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
i2c2: i2c@124a0000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x124a0000 0x1000>;
interrupts = <0 196 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi3: gsbi@16200000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <3>;
reg = <0x16200000 0x100>;
clocks = <&gcc GSBI3_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
i2c3: i2c@16280000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c3_pins>;
pinctrl-names = "default";
reg = <0x16280000 0x1000>;
interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI3_QUP_CLK>,
<&gcc GSBI3_H_CLK>;
clock-names = "core", "iface";
};
};
gsbi5: gsbi@1a200000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <5>;
reg = <0x1a200000 0x03>;
clocks = <&gcc GSBI5_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi5_serial: serial@1a240000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x1a240000 0x100>,
<0x1a200000 0x03>;
interrupts = <0 154 0x0>;
clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
};
gsbi6: gsbi@16500000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <6>;
reg = <0x16500000 0x03>;
clocks = <&gcc GSBI6_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi6_serial: serial@16540000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16540000 0x100>,
<0x16500000 0x03>;
interrupts = <0 156 0x0>;
clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
};
gsbi7: gsbi@16600000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <7>;
reg = <0x16600000 0x100>;
clocks = <&gcc GSBI7_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
gsbi7_serial: serial@16640000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16640000 0x1000>,
<0x16600000 0x1000>;
interrupts = <0 158 0x0>;
clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
};
rng@1a500000 {
compatible = "qcom,prng";
reg = <0x1a500000 0x200>;
clocks = <&gcc PRNG_CLK>;
clock-names = "core";
};
qcom,ssbi@500000 {
compatible = "qcom,ssbi";
reg = <0x00500000 0x1000>;
qcom,controller-type = "pmic-arbiter";
pmicintc: pmic@0 {
compatible = "qcom,pm8921";
interrupt-parent = <&tlmm_pinmux>;
interrupts = <74 8>;
#interrupt-cells = <2>;
interrupt-controller;
#address-cells = <1>;
#size-cells = <0>;
pm8921_gpio: gpio@150 {
compatible = "qcom,pm8921-gpio",
"qcom,ssbi-gpio";
reg = <0x150>;
interrupts = <192 1>, <193 1>, <194 1>,
<195 1>, <196 1>, <197 1>,
<198 1>, <199 1>, <200 1>,
<201 1>, <202 1>, <203 1>,
<204 1>, <205 1>, <206 1>,
<207 1>, <208 1>, <209 1>,
<210 1>, <211 1>, <212 1>,
<213 1>, <214 1>, <215 1>,
<216 1>, <217 1>, <218 1>,
<219 1>, <220 1>, <221 1>,
<222 1>, <223 1>, <224 1>,
<225 1>, <226 1>, <227 1>,
<228 1>, <229 1>, <230 1>,
<231 1>, <232 1>, <233 1>,
<234 1>, <235 1>;
gpio-controller;
#gpio-cells = <2>;
};
pm8921_mpps: mpps@50 {
compatible = "qcom,pm8921-mpp",
"qcom,ssbi-mpp";
reg = <0x50>;
gpio-controller;
#gpio-cells = <2>;
interrupts =
<128 1>, <129 1>, <130 1>, <131 1>,
<132 1>, <133 1>, <134 1>, <135 1>,
<136 1>, <137 1>, <138 1>, <139 1>;
};
rtc@11d {
compatible = "qcom,pm8921-rtc";
interrupt-parent = <&pmicintc>;
interrupts = <39 1>;
reg = <0x11d>;
allow-set-time;
};
pwrkey@1c {
compatible = "qcom,pm8921-pwrkey";
reg = <0x1c>;
interrupt-parent = <&pmicintc>;
interrupts = <50 1>, <51 1>;
debounce = <15625>;
pull-up;
};
};
};
gcc: clock-controller@900000 {
compatible = "qcom,gcc-apq8064";
reg = <0x00900000 0x4000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
lcc: clock-controller@28000000 {
compatible = "qcom,lcc-apq8064";
reg = <0x28000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
mmcc: clock-controller@4000000 {
compatible = "qcom,mmcc-apq8064";
reg = <0x4000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
l2cc: clock-controller@2011000 {
compatible = "syscon";
reg = <0x2011000 0x1000>;
};
rpm@108000 {
compatible = "qcom,rpm-apq8064";
reg = <0x108000 0x1000>;
qcom,ipc = <&l2cc 0x8 2>;
interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "ack", "err", "wakeup";
regulators {
compatible = "qcom,rpm-pm8921-regulators";
pm8921_s1: s1 {};
pm8921_s2: s2 {};
pm8921_s3: s3 {};
pm8921_s4: s4 {};
pm8921_s7: s7 {};
pm8921_s8: s8 {};
pm8921_l1: l1 {};
pm8921_l2: l2 {};
pm8921_l3: l3 {};
pm8921_l4: l4 {};
pm8921_l5: l5 {};
pm8921_l6: l6 {};
pm8921_l7: l7 {};
pm8921_l8: l8 {};
pm8921_l9: l9 {};
pm8921_l10: l10 {};
pm8921_l11: l11 {};
pm8921_l12: l12 {};
pm8921_l14: l14 {};
pm8921_l15: l15 {};
pm8921_l16: l16 {};
pm8921_l17: l17 {};
pm8921_l18: l18 {};
pm8921_l21: l21 {};
pm8921_l22: l22 {};
pm8921_l23: l23 {};
pm8921_l24: l24 {};
pm8921_l25: l25 {};
pm8921_l26: l26 {};
pm8921_l27: l27 {};
pm8921_l28: l28 {};
pm8921_l29: l29 {};
pm8921_lvs1: lvs1 {};
pm8921_lvs2: lvs2 {};
pm8921_lvs3: lvs3 {};
pm8921_lvs4: lvs4 {};
pm8921_lvs5: lvs5 {};
pm8921_lvs6: lvs6 {};
pm8921_lvs7: lvs7 {};
pm8921_usb_switch: usb-switch {};
pm8921_hdmi_switch: hdmi-switch {
bias-pull-down;
};
pm8921_ncp: ncp {};
};
};
usb1_phy: phy@12500000 {
compatible = "qcom,usb-otg-ci";
reg = <0x12500000 0x400>;
interrupts = <GIC_SPI 100 IRQ_TYPE_NONE>;
status = "disabled";
dr_mode = "host";
clocks = <&gcc USB_HS1_XCVR_CLK>,
<&gcc USB_HS1_H_CLK>;
clock-names = "core", "iface";
resets = <&gcc USB_HS1_RESET>;
reset-names = "link";
};
usb3_phy: phy@12520000 {
compatible = "qcom,usb-otg-ci";
reg = <0x12520000 0x400>;
interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>;
status = "disabled";
dr_mode = "host";
clocks = <&gcc USB_HS3_XCVR_CLK>,
<&gcc USB_HS3_H_CLK>;
clock-names = "core", "iface";
resets = <&gcc USB_HS3_RESET>;
reset-names = "link";
};
usb4_phy: phy@12530000 {
compatible = "qcom,usb-otg-ci";
reg = <0x12530000 0x400>;
interrupts = <GIC_SPI 215 IRQ_TYPE_NONE>;
status = "disabled";
dr_mode = "host";
clocks = <&gcc USB_HS4_XCVR_CLK>,
<&gcc USB_HS4_H_CLK>;
clock-names = "core", "iface";
resets = <&gcc USB_HS4_RESET>;
reset-names = "link";
};
gadget1: gadget@12500000 {
compatible = "qcom,ci-hdrc";
reg = <0x12500000 0x400>;
status = "disabled";
dr_mode = "peripheral";
interrupts = <GIC_SPI 100 IRQ_TYPE_NONE>;
usb-phy = <&usb1_phy>;
};
usb1: usb@12500000 {
compatible = "qcom,ehci-host";
reg = <0x12500000 0x400>;
interrupts = <GIC_SPI 100 IRQ_TYPE_NONE>;
status = "disabled";
usb-phy = <&usb1_phy>;
};
usb3: usb@12520000 {
compatible = "qcom,ehci-host";
reg = <0x12520000 0x400>;
interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>;
status = "disabled";
usb-phy = <&usb3_phy>;
};
usb4: usb@12530000 {
compatible = "qcom,ehci-host";
reg = <0x12530000 0x400>;
interrupts = <GIC_SPI 215 IRQ_TYPE_NONE>;
status = "disabled";
usb-phy = <&usb4_phy>;
};
sata_phy0: phy@1b400000 {
compatible = "qcom,apq8064-sata-phy";
status = "disabled";
reg = <0x1b400000 0x200>;
reg-names = "phy_mem";
clocks = <&gcc SATA_PHY_CFG_CLK>;
clock-names = "cfg";
#phy-cells = <0>;
};
sata0: sata@29000000 {
compatible = "generic-ahci";
status = "disabled";
reg = <0x29000000 0x180>;
interrupts = <GIC_SPI 209 IRQ_TYPE_NONE>;
clocks = <&gcc SFAB_SATA_S_H_CLK>,
<&gcc SATA_H_CLK>,
<&gcc SATA_A_CLK>,
<&gcc SATA_RXOOB_CLK>,
<&gcc SATA_PMALIVE_CLK>;
clock-names = "slave_iface",
"iface",
"bus",
"rxoob",
"core_pmalive";
assigned-clocks = <&gcc SATA_RXOOB_CLK>,
<&gcc SATA_PMALIVE_CLK>;
assigned-clock-rates = <100000000>, <100000000>;
phys = <&sata_phy0>;
phy-names = "sata-phy";
};
/* Temporary fixed regulator */
sdcc1bam:dma@12402000{
compatible = "qcom,bam-v1.3.0";
reg = <0x12402000 0x8000>;
interrupts = <0 98 0>;
clocks = <&gcc SDC1_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
sdcc3bam:dma@12182000{
compatible = "qcom,bam-v1.3.0";
reg = <0x12182000 0x8000>;
interrupts = <0 96 0>;
clocks = <&gcc SDC3_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
sdcc4bam:dma@121c2000{
compatible = "qcom,bam-v1.3.0";
reg = <0x121c2000 0x8000>;
interrupts = <0 95 0>;
clocks = <&gcc SDC4_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
amba {
compatible = "arm,amba-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
sdcc1: sdcc@12400000 {
status = "disabled";
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
reg = <0x12400000 0x2000>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <8>;
max-frequency = <96000000>;
non-removable;
cap-sd-highspeed;
cap-mmc-highspeed;
dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
dma-names = "tx", "rx";
};
sdcc3: sdcc@12180000 {
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
status = "disabled";
reg = <0x12180000 0x2000>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <4>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <192000000>;
no-1-8-v;
dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
dma-names = "tx", "rx";
};
sdcc4: sdcc@121c0000 {
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
status = "disabled";
reg = <0x121c0000 0x2000>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <4>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <48000000>;
dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&sdc4_gpios>;
};
};
tcsr: syscon@1a400000 {
compatible = "qcom,tcsr-apq8064", "syscon";
reg = <0x1a400000 0x100>;
};
pcie: pci@1b500000 {
compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
reg = <0x1b500000 0x1000
0x1b502000 0x80
0x1b600000 0x100
0x0ff00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000 /* I/O */
0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */
interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc PCIE_A_CLK>,
<&gcc PCIE_H_CLK>,
<&gcc PCIE_PHY_REF_CLK>;
clock-names = "core", "iface", "phy";
resets = <&gcc PCIE_ACLK_RESET>,
<&gcc PCIE_HCLK_RESET>,
<&gcc PCIE_POR_RESET>,
<&gcc PCIE_PCI_RESET>,
<&gcc PCIE_PHY_RESET>;
reset-names = "axi", "ahb", "por", "pci", "phy";
status = "disabled";
};
};
};