#
# This file adds to the values in AR91XX_BASE.hints.
#
# $FreeBSD$

# Hard-code the PHY for now, until there's switch phy support.
# hint.arge.0.phymask=0x000c
hint.arge.0.phymask=0x0000
hint.arge.0.media=1000
hint.arge.0.fduplex=1
# Where is the MAC address stored in flash for this particular unit.
hint.arge.0.eeprommac=0x1f01fc00

# This isn't used, but configure it anyway.
# This should eventually just not be configured, but the if then
# needs to be properly disabled or spurious interrupts occur.
hint.arge.1.phymask=0x0

# Where the ART is
hint.ath.0.eepromaddr=0x1fff1000

#
# Define a slightly custom flash layout.

# The default flash layout:
#
# 128k: uboot
# 1024k: kernel
# 4096k: rootfs
# 2816: unknown
# 64k: board config?
# 64k: ART
#
# from printenv:
# bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init
#    mtdparts=ar9100-nor0:128k(u-boot),1024k(kernel),4096k(rootfs),64k(art)

# This isn't a lot of space!
# So:
# 128k: uboot
# 2048k: kernel
# 5888k: rootfs
# 64k: config
# 64k: ART

hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x00020000
hint.map.0.name="uboot"
hint.map.0.readonly=1

hint.map.1.at="flash/spi0"
hint.map.1.start=0x00020000
hint.map.1.end="search:0x00100000:0x10000:.!/bin/sh"
hint.map.1.name="kernel"
hint.map.1.readonly=1

hint.map.2.at="flash/spi0"
hint.map.2.start="search:0x00100000:0x10000:.!/bin/sh"
hint.map.2.end=0x007e0000
hint.map.2.name="rootfs"
hint.map.2.readonly=1

hint.map.3.at="flash/spi0"
hint.map.3.start=0x007e0000
hint.map.3.end=0x007f0000
hint.map.3.name="cfg"
hint.map.3.readonly=0

# This is radio calibration section.  It is (or should be!) unique
# for each board, to take into account thermal and electrical differences
# as well as the regulatory compliance data.
#
hint.map.4.at="flash/spi0"
hint.map.4.start=0x007f0000
hint.map.4.end=0x00800000
hint.map.4.name="art"
hint.map.4.readonly=1

# GPIO specific configuration block

# Don't flip on anything that isn't already enabled.
# This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
# not used here.
hint.gpio.0.function_set=0x00002000
hint.gpio.0.function_clear=0x00000000

# These are the GPIO LEDs and buttons which can be software controlled.
hint.gpio.0.pinmask=0x001c02ae

# pin 1 - USB (LED)
# pin 2 - System (LED)
# Pin 3 - Reset (input)
# Pin 5 - QSS (LED)
# Pin 7 - QSS Button (input)
# Pin 8 - wired into the chip reset line
# Pin 9 - WLAN
# Pin 10 - UART TX (not GPIO)
# Pin 13 - UART RX (not GPIO)
# Pin 18 - RTL8366RB switch data line
# Pin 19 - RTL8366RB switch clock line
# Pin 20 - "GPIO20"

# LEDs are configured separately and driven by the LED device
#hint.gpioled.0.at="gpiobus0"
#hint.gpioled.0.name="usb"
#hint.gpioled.0.pins=0x0002

hint.gpioled.1.at="gpiobus0"
hint.gpioled.1.name="system"
hint.gpioled.1.pins=0x0004

hint.gpioled.2.at="gpiobus0"
hint.gpioled.2.name="qss"
hint.gpioled.2.pins=0x0020

hint.gpioled.3.at="gpiobus0"
hint.gpioled.3.name="wlan"
hint.gpioled.3.pins=0x0200

# GPIO I2C bus
hint.gpioiic.0.at="gpiobus0"
hint.gpioiic.0.pins=0xc0000
hint.gpioiic.0.scl=1
hint.gpioiic.0.sda=0

# I2C bus
# Don't be strict about I2C protocol - the relaxed semantics are required
# by the realtek switch PHY.
hint.iicbus.0.strict=0

# Bit bang bus - override default delay
#hint.iicbb.0.udelay=3