/*
* Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include "msm8996.dtsi"
#include "pm8994.dtsi"
#include "pmi8994.dtsi"
#include "apq8096-db820c-pins.dtsi"
#include "apq8096-db820c-pmic-pins.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
/*
* GPIO name legend: proper name = the GPIO line is used as GPIO
* NC = not connected (pin out but not routed from the chip to
* anything the board)
* "[PER]" = pin is muxed for [peripheral] (not GPIO)
* LSEC = Low Speed External Connector
* P HSEC = Primary High Speed External Connector
* S HSEC = Secondary High Speed External Connector
* J14 = Camera Connector
* TP = Test Points
*
* Line names are taken from the schematic "DragonBoard 820c",
* drawing no: LM25-P2751-1
*
* For the lines routed to the external connectors the
* lines are named after the 96Boards CE Specification 1.0,
* Appendix "Expansion Connector Signal Description".
*
* When the 96Board naming of a line and the schematic name of
* the same line are in conflict, the 96Board specification
* takes precedence, which means that the external UART on the
* LSEC is named UART0 while the schematic and SoC names this
* UART3. This is only for the informational lines i.e. "[FOO]",
* the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
* ones actually used for GPIO.
*/
/ {
aliases {
serial0 = &blsp2_uart1;
serial1 = &blsp2_uart2;
serial2 = &blsp1_uart1;
i2c0 = &blsp1_i2c2;
i2c1 = &blsp2_i2c1;
i2c2 = &blsp2_i2c0;
spi0 = &blsp1_spi0;
spi1 = &blsp2_spi5;
};
chosen {
stdout-path = "serial0:115200n8";
};
clocks {
divclk4: divclk4 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "divclk4";
pinctrl-names = "default";
pinctrl-0 = <&divclk4_pin_a>;
};
};
soc {
serial@7570000 {
label = "BT-UART";
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart1_default>;
pinctrl-1 = <&blsp1_uart1_sleep>;
bluetooth {
compatible = "qcom,qca6174-bt";
/* bt_disable_n gpio */
enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
clocks = <&divclk4>;
};
};
serial@75b0000 {
label = "LS-UART1";
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_uart1_2pins_default>;
pinctrl-1 = <&blsp2_uart1_2pins_sleep>;
};
serial@75b1000 {
label = "LS-UART0";
status = "disabled";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp2_uart2_4pins_default>;
pinctrl-1 = <&blsp2_uart2_4pins_sleep>;
};
i2c@7577000 {
/* On Low speed expansion */
label = "LS-I2C0";
status = "okay";
};
i2c@75b6000 {
/* On Low speed expansion */
label = "LS-I2C1";
status = "okay";
};
spi@7575000 {
/* On Low speed expansion */
label = "LS-SPI0";
status = "okay";
};
i2c@75b5000 {
/* On High speed expansion */
label = "HS-I2C2";
status = "okay";
};
spi@75ba000{
/* On High speed expansion */
label = "HS-SPI1";
status = "okay";
};
sdhci@74a4900 {
/* External SD card */
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
cd-gpios = <&msmgpio 38 0x1>;
vmmc-supply = <&pm8994_l21>;
vqmmc-supply = <&pm8994_l13>;
status = "okay";
};
phy@627000 {
status = "okay";
};
ufshc@624000 {
status = "okay";
};
pinctrl@1010000 {
gpio-line-names =
"[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */
"[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */
"[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */
"[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */
"[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */
"[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */
"[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */
"[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */
"GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */
"TP93", /* GPIO_9 */
"GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */
"[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */
"NC", /* GPIO_12 */
"[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */
"[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */
"[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */
"TP99", /* GPIO_16 */
"[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */
"[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */
"[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */
"[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */
"FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */
"FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */
"GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */
"GPIO-D", /* GPIO_24, LSEC pin 26 */
"GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */
"GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */
"BLSP6_I2C_SDA", /* GPIO_27 */
"BLSP6_I2C_SCL", /* GPIO_28 */
"GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */
"GPIO30", /* GPIO_30, S HSEC pin 4 */
"HDMI_CEC", /* GPIO_31 */
"HDMI_DDC_CLOCK", /* GPIO_32 */
"HDMI_DDC_DATA", /* GPIO_33 */
"HDMI_HOT_PLUG_DETECT", /* GPIO_34 */
"PCIE0_RST_N", /* GPIO_35 */
"PCIE0_CLKREQ_N", /* GPIO_36 */
"PCIE0_WAKE", /* GPIO_37 */
"SD_CARD_DET_N", /* GPIO_38 */
"TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */
"W_DISABLE_N", /* GPIO_40 */
"[BLSP9_UART_TX]", /* GPIO_41 */
"[BLSP9_UART_RX]", /* GPIO_42 */
"[BLSP2_UART_CTS_N]", /* GPIO_43 */
"[BLSP2_UART_RFR_N]", /* GPIO_44 */
"[BLSP3_UART_TX]", /* GPIO_45 */
"[BLSP3_UART_RX]", /* GPIO_46 */
"[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */
"[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */
"[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */
"[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */
"[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */
"[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */
"[CODEC_INT1_N]", /* GPIO_53 */
"[CODEC_INT2_N]", /* GPIO_54 */
"[BLSP7_I2C_SDA]", /* GPIO_55 */
"[BLSP7_I2C_SCL]", /* GPIO_56 */
"MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */
"[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */
"[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */
"[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */
"[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */
"GPIO-E", /* GPIO_62, LSEC pin 27 */
"TP87", /* GPIO_63 */
"[CODEC_RST_N]", /* GPIO_64 */
"[PCM1_CLK]", /* GPIO_65 */
"[PCM1_SYNC]", /* GPIO_66 */
"[PCM1_DIN]", /* GPIO_67 */
"[PCM1_DOUT]", /* GPIO_68 */
"AUDIO_REF_CLK", /* GPIO_69 */
"SLIMBUS_CLK", /* GPIO_70 */
"SLIMBUS_DATA0", /* GPIO_71 */
"SLIMBUS_DATA1", /* GPIO_72 */
"NC", /* GPIO_73 */
"NC", /* GPIO_74 */
"NC", /* GPIO_75 */
"NC", /* GPIO_76 */
"TP94", /* GPIO_77 */
"NC", /* GPIO_78 */
"TP95", /* GPIO_79 */
"GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */
"TP88", /* GPIO_81 */
"TP89", /* GPIO_82 */
"TP90", /* GPIO_83 */
"TP91", /* GPIO_84 */
"[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */
"[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */
"[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */
"[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */
"TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */
"TSIF1_EN", /* GPIO_90, S HSEC pin 46 */
"TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */
"NC", /* GPIO_92 */
"TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */
"TSIF2_EN", /* GPIO_94, S HSEC pin 56 */
"TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */
"TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */
"NC", /* GPIO_97 */
"CAM1_STANDBY_N", /* GPIO_98 */
"NC", /* GPIO_99 */
"NC", /* GPIO_100 */
"[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */
"BOOT_CONFIG1", /* GPIO_102 */
"USB_HUB_RESET", /* GPIO_103 */
"CAM1_RST_N", /* GPIO_104 */
"NC", /* GPIO_105 */
"NC", /* GPIO_106 */
"NC", /* GPIO_107 */
"NC", /* GPIO_108 */
"NC", /* GPIO_109 */
"NC", /* GPIO_110 */
"NC", /* GPIO_111 */
"NC", /* GPIO_112 */
"PMI8994_BUA", /* GPIO_113 */
"PCIE2_RST_N", /* GPIO_114 */
"PCIE2_CLKREQ_N", /* GPIO_115 */
"PCIE2_WAKE", /* GPIO_116 */
"SSC_IRQ_0", /* GPIO_117 */
"SSC_IRQ_1", /* GPIO_118 */
"SSC_IRQ_2", /* GPIO_119 */
"NC", /* GPIO_120 */
"GPIO121", /* GPIO_121, S HSEC pin 2 */
"NC", /* GPIO_122 */
"SSC_IRQ_6", /* GPIO_123 */
"SSC_IRQ_7", /* GPIO_124 */
"GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */
"BOOT_CONFIG5", /* GPIO_126 */
"NC", /* GPIO_127 */
"NC", /* GPIO_128 */
"BOOT_CONFIG7", /* GPIO_129 */
"PCIE1_RST_N", /* GPIO_130 */
"PCIE1_CLKREQ_N", /* GPIO_131 */
"PCIE1_WAKE", /* GPIO_132 */
"GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */
"NC", /* GPIO_134 */
"NC", /* GPIO_135 */
"BOOT_CONFIG8", /* GPIO_136 */
"NC", /* GPIO_137 */
"NC", /* GPIO_138 */
"GPS_SSBI2", /* GPIO_139 */
"GPS_SSBI1", /* GPIO_140 */
"NC", /* GPIO_141 */
"NC", /* GPIO_142 */
"NC", /* GPIO_143 */
"BOOT_CONFIG6", /* GPIO_144 */
"NC", /* GPIO_145 */
"NC", /* GPIO_146 */
"NC", /* GPIO_147 */
"NC", /* GPIO_148 */
"NC"; /* GPIO_149 */
};
qcom,spmi@400f000 {
pmic@0 {
gpios@c000 {
gpio-line-names =
"NC",
"KEY_VOLP_N",
"NC",
"BL1_PWM",
"GPIO-F", /* BL0_PWM, LSEC pin 28 */
"BL1_EN",
"NC",
"WLAN_EN",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"DIVCLK1",
"DIVCLK2",
"DIVCLK3",
"DIVCLK4",
"BT_EN",
"PMIC_SLB",
"PMIC_BUA",
"USB_VBUS_DET";
};
mpps@a000 {
gpio-line-names =
"VDDPX_BIAS",
"WIFI_LED",
"NC",
"BT_LED",
"PM_MPP05",
"PM_MPP06",
"PM_MPP07",
"NC";
};
};
pmic@2 {
gpios@c000 {
gpio-line-names =
"NC",
"SPKR_AMP_EN1",
"SPKR_AMP_EN2",
"TP61",
"NC",
"USB2_VBUS_DET",
"NC",
"NC",
"NC",
"NC";
};
};
};
phy@34000 {
status = "okay";
};
phy@7410000 {
status = "okay";
};
phy@7411000 {
status = "okay";
};
phy@7412000 {
status = "okay";
};
usb@6af8800 {
status = "okay";
extcon = <&usb3_id>;
dwc3@6a00000 {
extcon = <&usb3_id>;
dr_mode = "otg";
};
};
usb3_id: usb3-id {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb3_vbus_det_gpio>;
};
usb@76f8800 {
status = "okay";
extcon = <&usb2_id>;
dwc3@7600000 {
extcon = <&usb2_id>;
dr_mode = "otg";
maximum-speed = "high-speed";
};
};
usb2_id: usb2-id {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb2_vbus_det_gpio>;
};
wlan_en: wlan-en-1-8v {
pinctrl-names = "default";
pinctrl-0 = <&wlan_en_gpios>;
compatible = "regulator-fixed";
regulator-name = "wlan-en-regulator";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&pm8994_gpios 8 0>;
/* WLAN card specific delay */
startup-delay-us = <70000>;
enable-active-high;
};
agnoc@0 {
pcie@600000 {
status = "okay";
perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
vddpe-3v3-supply = <&wlan_en>;
};
pcie@608000 {
status = "okay";
perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
};
pcie@610000 {
status = "okay";
perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
};
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
autorepeat;
pinctrl-names = "default";
pinctrl-0 = <&volume_up_gpio>;
button@0 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
};
};
rpm-glink {
rpm_requests {
pm8994-regulators {
vdd_l1-supply = <&pm8994_s3>;
vdd_l2_l26_l28-supply = <&pm8994_s3>;
vdd_l3_l11-supply = <&pm8994_s3>;
vdd_l4_l27_l31-supply = <&pm8994_s3>;
vdd_l5_l7-supply = <&pm8994_s5>;
vdd_l14_l15-supply = <&pm8994_s5>;
vdd_l20_l21-supply = <&pm8994_s5>;
vdd_l25-supply = <&pm8994_s3>;
s3 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
};
/**
* 1.8v required on LS expansion
* for mezzanine boards
*/
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
s5 {
regulator-min-microvolt = <2150000>;
regulator-max-microvolt = <2150000>;
};
s7 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
};
l1 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
l2 {
regulator-min-microvolt = <1250000>;
regulator-max-microvolt = <1250000>;
};
l3 {
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <850000>;
};
l4 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
l6 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
l8 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l9 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l10 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l11 {
regulator-min-microvolt = <1150000>;
regulator-max-microvolt = <1150000>;
};
l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
l14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l16 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
l17 {
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
};
l18 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2900000>;
};
l19 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
l20 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-allow-set-load;
};
l21 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
};
l22 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
l23 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
l24 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
};
l25 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-allow-set-load;
};
l27 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
};
l28 {
regulator-min-microvolt = <925000>;
regulator-max-microvolt = <925000>;
regulator-allow-set-load;
};
l29 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
l30 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l32 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
};
};
};
&spmi_bus {
pmic@0 {
pon@800 {
resin {
compatible = "qcom,pm8941-resin";
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
linux,code = <KEY_VOLUMEDOWN>;
};
};
};
};