// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the R-Car Gen3 ULCB board
*
* Copyright (C) 2016 Renesas Electronics Corp.
* Copyright (C) 2016 Cogent Embedded, Inc.
*/
/*
* SSI-AK4613
* aplay -D plughw:0,0 xxx.wav
* arecord -D plughw:0,0 xxx.wav
* SSI-HDMI
* aplay -D plughw:0,1 xxx.wav
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Renesas R-Car Gen3 ULCB board";
aliases {
serial0 = &scif2;
ethernet0 = &avb;
};
chosen {
bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
stdout-path = "serial0:115200n8";
};
audio_clkout: audio-clkout {
/*
* This is same as <&rcar_sound 0>
* but needed to avoid cs2000/rcar_sound probe dead-lock
*/
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <12288000>;
};
hdmi0-out {
compatible = "hdmi-connector";
type = "a";
port {
hdmi0_con: endpoint {
};
};
};
keyboard {
compatible = "gpio-keys";
key-1 {
linux,code = <KEY_1>;
label = "SW3";
wakeup-source;
debounce-interval = <20>;
gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
led5 {
gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
};
led6 {
gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
};
};
reg_1p8v: regulator0 {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
reg_3p3v: regulator1 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
sound_card: sound {
compatible = "audio-graph-card";
label = "rcar-sound";
dais = <&rsnd_port0 /* ak4613 */
&rsnd_port1 /* HDMI0 */
>;
};
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
states = <3300000 1>, <1800000 0>;
};
x12_clk: x12 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24576000>;
};
x23_clk: x23-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
};
&audio_clk_a {
clock-frequency = <22579200>;
};
&avb {
pinctrl-0 = <&avb_pins>;
pinctrl-names = "default";
phy-handle = <&phy0>;
phy-mode = "rgmii-txid";
status = "okay";
phy0: ethernet-phy@0 {
rxc-skew-ps = <1500>;
reg = <0>;
interrupt-parent = <&gpio2>;
interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
};
};
&du {
status = "okay";
};
&ehci1 {
status = "okay";
};
&extal_clk {
clock-frequency = <16666666>;
};
&extalr_clk {
clock-frequency = <32768>;
};
&hdmi0 {
status = "okay";
ports {
port@1 {
reg = <1>;
rcar_dw_hdmi0_out: endpoint {
remote-endpoint = <&hdmi0_con>;
};
};
port@2 {
reg = <2>;
dw_hdmi0_snd_in: endpoint {
remote-endpoint = <&rsnd_for_hdmi>;
};
};
};
};
&hdmi0_con {
remote-endpoint = <&rcar_dw_hdmi0_out>;
};
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "default";
status = "okay";
clock-frequency = <100000>;
ak4613: codec@10 {
compatible = "asahi-kasei,ak4613";
#sound-dai-cells = <0>;
reg = <0x10>;
clocks = <&rcar_sound 3>;
asahi-kasei,in1-single-end;
asahi-kasei,in2-single-end;
asahi-kasei,out1-single-end;
asahi-kasei,out2-single-end;
asahi-kasei,out3-single-end;
asahi-kasei,out4-single-end;
asahi-kasei,out5-single-end;
asahi-kasei,out6-single-end;
port {
ak4613_endpoint: endpoint {
remote-endpoint = <&rsnd_for_ak4613>;
};
};
};
cs2000: clk-multiplier@4f {
#clock-cells = <0>;
compatible = "cirrus,cs2000-cp";
reg = <0x4f>;
clocks = <&audio_clkout>, <&x12_clk>;
clock-names = "clk_in", "ref_clk";
assigned-clocks = <&cs2000>;
assigned-clock-rates = <24576000>; /* 1/1 divide */
};
};
&i2c4 {
status = "okay";
clock-frequency = <400000>;
versaclock5: clock-generator@6a {
compatible = "idt,5p49v5925";
reg = <0x6a>;
#clock-cells = <1>;
clocks = <&x23_clk>;
clock-names = "xin";
};
};
&i2c_dvfs {
status = "okay";
clock-frequency = <400000>;
pmic: pmic@30 {
pinctrl-0 = <&irq0_pins>;
pinctrl-names = "default";
compatible = "rohm,bd9571mwv";
reg = <0x30>;
interrupt-parent = <&intc_ex>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
rohm,ddr-backup-power = <0xf>;
rohm,rstbmode-pulse;
regulators {
dvfs: dvfs {
regulator-name = "dvfs";
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1030000>;
regulator-boot-on;
regulator-always-on;
};
};
};
};
&ohci1 {
status = "okay";
};
&pfc {
pinctrl-0 = <&scif_clk_pins>;
pinctrl-names = "default";
avb_pins: avb {
mux {
groups = "avb_link", "avb_mdio", "avb_mii";
function = "avb";
};
pins_mdio {
groups = "avb_mdio";
drive-strength = <24>;
};
pins_mii_tx {
pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
"PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
drive-strength = <12>;
};
};
i2c2_pins: i2c2 {
groups = "i2c2_a";
function = "i2c2";
};
irq0_pins: irq0 {
groups = "intc_ex_irq0";
function = "intc_ex";
};
scif2_pins: scif2 {
groups = "scif2_data_a";
function = "scif2";
};
scif_clk_pins: scif_clk {
groups = "scif_clk_a";
function = "scif_clk";
};
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
power-source = <3300>;
};
sdhi0_pins_uhs: sd0_uhs {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
power-source = <1800>;
};
sdhi2_pins: sd2 {
groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
function = "sdhi2";
power-source = <1800>;
};
sound_pins: sound {
groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
function = "ssi";
};
sound_clk_pins: sound-clk {
groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
"audio_clkout_a", "audio_clkout3_a";
function = "audio_clk";
};
usb1_pins: usb1 {
groups = "usb1";
function = "usb1";
};
};
&rcar_sound {
pinctrl-0 = <&sound_pins &sound_clk_pins>;
pinctrl-names = "default";
/* Single DAI */
#sound-dai-cells = <0>;
/* audio_clkout0/1/2/3 */
#clock-cells = <1>;
clock-frequency = <12288000 11289600>;
status = "okay";
/* update <audio_clk_b> to <cs2000> */
clocks = <&cpg CPG_MOD 1005>,
<&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
<&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
<&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
<&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
<&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
<&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
<&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
<&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
<&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
<&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
<&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
<&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
<&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
<&audio_clk_a>, <&cs2000>,
<&audio_clk_c>,
<&cpg CPG_CORE CPG_AUDIO_CLK_I>;
ports {
#address-cells = <1>;
#size-cells = <0>;
rsnd_port0: port@0 {
reg = <0>;
rsnd_for_ak4613: endpoint {
remote-endpoint = <&ak4613_endpoint>;
dai-format = "left_j";
bitclock-master = <&rsnd_for_ak4613>;
frame-master = <&rsnd_for_ak4613>;
playback = <&ssi0 &src0 &dvc0>;
capture = <&ssi1 &src1 &dvc1>;
};
};
rsnd_port1: port@1 {
reg = <1>;
rsnd_for_hdmi: endpoint {
remote-endpoint = <&dw_hdmi0_snd_in>;
dai-format = "i2s";
bitclock-master = <&rsnd_for_hdmi>;
frame-master = <&rsnd_for_hdmi>;
playback = <&ssi2>;
};
};
};
};
&rwdt {
timeout-sec = <60>;
status = "okay";
};
&scif2 {
pinctrl-0 = <&scif2_pins>;
pinctrl-names = "default";
status = "okay";
};
&scif_clk {
clock-frequency = <14745600>;
};
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
pinctrl-1 = <&sdhi0_pins_uhs>;
pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
bus-width = <4>;
sd-uhs-sdr50;
sd-uhs-sdr104;
status = "okay";
};
&sdhi2 {
/* used for on-board 8bit eMMC */
pinctrl-0 = <&sdhi2_pins>;
pinctrl-1 = <&sdhi2_pins>;
pinctrl-names = "default", "state_uhs";
vmmc-supply = <®_3p3v>;
vqmmc-supply = <®_1p8v>;
bus-width = <8>;
mmc-hs200-1_8v;
mmc-hs400-1_8v;
non-removable;
status = "okay";
};
&ssi1 {
shared-pin;
};
&usb2_phy1 {
pinctrl-0 = <&usb1_pins>;
pinctrl-names = "default";
status = "okay";
};