/* SPDX-License-Identifier: BSD-3-Clause */
/*
* Texas Instruments System Control Interface (TISCI) Protocol
*
* Communication protocol with TI SCI hardware
* The system works in a message response protocol
* See: http://processors.wiki.ti.com/index.php/TISCI for details
*
* Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
*/
#ifndef __TI_SCI_H
#define __TI_SCI_H
/* Generic Messages */
#define TI_SCI_MSG_ENABLE_WDT 0x0000
#define TI_SCI_MSG_WAKE_RESET 0x0001
#define TI_SCI_MSG_VERSION 0x0002
#define TI_SCI_MSG_WAKE_REASON 0x0003
#define TI_SCI_MSG_GOODBYE 0x0004
#define TI_SCI_MSG_SYS_RESET 0x0005
/* Device requests */
#define TI_SCI_MSG_SET_DEVICE_STATE 0x0200
#define TI_SCI_MSG_GET_DEVICE_STATE 0x0201
#define TI_SCI_MSG_SET_DEVICE_RESETS 0x0202
/* Clock requests */
#define TI_SCI_MSG_SET_CLOCK_STATE 0x0100
#define TI_SCI_MSG_GET_CLOCK_STATE 0x0101
#define TI_SCI_MSG_SET_CLOCK_PARENT 0x0102
#define TI_SCI_MSG_GET_CLOCK_PARENT 0x0103
#define TI_SCI_MSG_GET_NUM_CLOCK_PARENTS 0x0104
#define TI_SCI_MSG_SET_CLOCK_FREQ 0x010c
#define TI_SCI_MSG_QUERY_CLOCK_FREQ 0x010d
#define TI_SCI_MSG_GET_CLOCK_FREQ 0x010e
/* Resource Management Requests */
#define TI_SCI_MSG_GET_RESOURCE_RANGE 0x1500
/* IRQ requests */
#define TI_SCI_MSG_SET_IRQ 0x1000
#define TI_SCI_MSG_FREE_IRQ 0x1001
/* NAVSS resource management */
/* Ringacc requests */
#define TI_SCI_MSG_RM_RING_ALLOCATE 0x1100
#define TI_SCI_MSG_RM_RING_FREE 0x1101
#define TI_SCI_MSG_RM_RING_RECONFIG 0x1102
#define TI_SCI_MSG_RM_RING_RESET 0x1103
#define TI_SCI_MSG_RM_RING_CFG 0x1110
#define TI_SCI_MSG_RM_RING_GET_CFG 0x1111
/* PSI-L requests */
#define TI_SCI_MSG_RM_PSIL_PAIR 0x1280
#define TI_SCI_MSG_RM_PSIL_UNPAIR 0x1281
#define TI_SCI_MSG_RM_UDMAP_TX_ALLOC 0x1200
#define TI_SCI_MSG_RM_UDMAP_TX_FREE 0x1201
#define TI_SCI_MSG_RM_UDMAP_RX_ALLOC 0x1210
#define TI_SCI_MSG_RM_UDMAP_RX_FREE 0x1211
#define TI_SCI_MSG_RM_UDMAP_FLOW_CFG 0x1220
#define TI_SCI_MSG_RM_UDMAP_OPT_FLOW_CFG 0x1221
#define TISCI_MSG_RM_UDMAP_TX_CH_CFG 0x1205
#define TISCI_MSG_RM_UDMAP_TX_CH_GET_CFG 0x1206
#define TISCI_MSG_RM_UDMAP_RX_CH_CFG 0x1215
#define TISCI_MSG_RM_UDMAP_RX_CH_GET_CFG 0x1216
#define TISCI_MSG_RM_UDMAP_FLOW_CFG 0x1230
#define TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_CFG 0x1231
#define TISCI_MSG_RM_UDMAP_FLOW_GET_CFG 0x1232
#define TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_GET_CFG 0x1233
/* Processor Control requests */
#define TI_SCI_MSG_PROC_REQUEST 0xc000
#define TI_SCI_MSG_PROC_RELEASE 0xc001
#define TI_SCI_MSG_PROC_HANDOVER 0xc005
#define TI_SCI_MSG_SET_CONFIG 0xc100
#define TI_SCI_MSG_SET_CTRL 0xc101
#define TI_SCI_MSG_GET_STATUS 0xc400
/**
* struct ti_sci_msg_hdr - Generic Message Header for All messages and responses
* @type: Type of messages: One of TI_SCI_MSG* values
* @host: Host of the message
* @seq: Message identifier indicating a transfer sequence
* @flags: Flag for the message
*/
struct ti_sci_msg_hdr {
u16 type;
u8 host;
u8 seq;
#define TI_SCI_MSG_FLAG(val) (1 << (val))
#define TI_SCI_FLAG_REQ_GENERIC_NORESPONSE 0x0
#define TI_SCI_FLAG_REQ_ACK_ON_RECEIVED TI_SCI_MSG_FLAG(0)
#define TI_SCI_FLAG_REQ_ACK_ON_PROCESSED TI_SCI_MSG_FLAG(1)
#define TI_SCI_FLAG_RESP_GENERIC_NACK 0x0
#define TI_SCI_FLAG_RESP_GENERIC_ACK TI_SCI_MSG_FLAG(1)
/* Additional Flags */
u32 flags;
} __packed;
/**
* struct ti_sci_msg_resp_version - Response for a message
* @hdr: Generic header
* @firmware_description: String describing the firmware
* @firmware_revision: Firmware revision
* @abi_major: Major version of the ABI that firmware supports
* @abi_minor: Minor version of the ABI that firmware supports
*
* In general, ABI version changes follow the rule that minor version increments
* are backward compatible. Major revision changes in ABI may not be
* backward compatible.
*
* Response to a generic message with message type TI_SCI_MSG_VERSION
*/
struct ti_sci_msg_resp_version {
struct ti_sci_msg_hdr hdr;
char firmware_description[32];
u16 firmware_revision;
u8 abi_major;
u8 abi_minor;
} __packed;
/**
* struct ti_sci_msg_req_reboot - Reboot the SoC
* @hdr: Generic Header
*
* Request type is TI_SCI_MSG_SYS_RESET, responded with a generic
* ACK/NACK message.
*/
struct ti_sci_msg_req_reboot {
struct ti_sci_msg_hdr hdr;
} __packed;
/**
* struct ti_sci_msg_req_set_device_state - Set the desired state of the device
* @hdr: Generic header
* @id: Indicates which device to modify
* @reserved: Reserved space in message, must be 0 for backward compatibility
* @state: The desired state of the device.
*
* Certain flags can also be set to alter the device state:
* + MSG_FLAG_DEVICE_WAKE_ENABLED - Configure the device to be a wake source.
* The meaning of this flag will vary slightly from device to device and from
* SoC to SoC but it generally allows the device to wake the SoC out of deep
* suspend states.
* + MSG_FLAG_DEVICE_RESET_ISO - Enable reset isolation for this device.
* + MSG_FLAG_DEVICE_EXCLUSIVE - Claim this device exclusively. When passed
* with STATE_RETENTION or STATE_ON, it will claim the device exclusively.
* If another host already has this device set to STATE_RETENTION or STATE_ON,
* the message will fail. Once successful, other hosts attempting to set
* STATE_RETENTION or STATE_ON will fail.
*
* Request type is TI_SCI_MSG_SET_DEVICE_STATE, responded with a generic
* ACK/NACK message.
*/
struct ti_sci_msg_req_set_device_state {
/* Additional hdr->flags options */
#define MSG_FLAG_DEVICE_WAKE_ENABLED TI_SCI_MSG_FLAG(8)
#define MSG_FLAG_DEVICE_RESET_ISO TI_SCI_MSG_FLAG(9)
#define MSG_FLAG_DEVICE_EXCLUSIVE TI_SCI_MSG_FLAG(10)
struct ti_sci_msg_hdr hdr;
u32 id;
u32 reserved;
#define MSG_DEVICE_SW_STATE_AUTO_OFF 0
#define MSG_DEVICE_SW_STATE_RETENTION 1
#define MSG_DEVICE_SW_STATE_ON 2
u8 state;
} __packed;
/**
* struct ti_sci_msg_req_get_device_state - Request to get device.
* @hdr: Generic header
* @id: Device Identifier
*
* Request type is TI_SCI_MSG_GET_DEVICE_STATE, responded device state
* information
*/
struct ti_sci_msg_req_get_device_state {
struct ti_sci_msg_hdr hdr;
u32 id;
} __packed;
/**
* struct ti_sci_msg_resp_get_device_state - Response to get device request.
* @hdr: Generic header
* @context_loss_count: Indicates how many times the device has lost context. A
* driver can use this monotonic counter to determine if the device has
* lost context since the last time this message was exchanged.
* @resets: Programmed state of the reset lines.
* @programmed_state: The state as programmed by set_device.
* - Uses the MSG_DEVICE_SW_* macros
* @current_state: The actual state of the hardware.
*
* Response to request TI_SCI_MSG_GET_DEVICE_STATE.
*/
struct ti_sci_msg_resp_get_device_state {
struct ti_sci_msg_hdr hdr;
u32 context_loss_count;
u32 resets;
u8 programmed_state;
#define MSG_DEVICE_HW_STATE_OFF 0
#define MSG_DEVICE_HW_STATE_ON 1
#define MSG_DEVICE_HW_STATE_TRANS 2
u8 current_state;
} __packed;
/**
* struct ti_sci_msg_req_set_device_resets - Set the desired resets
* configuration of the device
* @hdr: Generic header
* @id: Indicates which device to modify
* @resets: A bit field of resets for the device. The meaning, behavior,
* and usage of the reset flags are device specific. 0 for a bit
* indicates releasing the reset represented by that bit while 1
* indicates keeping it held.
*
* Request type is TI_SCI_MSG_SET_DEVICE_RESETS, responded with a generic
* ACK/NACK message.
*/
struct ti_sci_msg_req_set_device_resets {
struct ti_sci_msg_hdr hdr;
u32 id;
u32 resets;
} __packed;
/**
* struct ti_sci_msg_req_set_clock_state - Request to setup a Clock state
* @hdr: Generic Header, Certain flags can be set specific to the clocks:
* MSG_FLAG_CLOCK_ALLOW_SSC: Allow this clock to be modified
* via spread spectrum clocking.
* MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE: Allow this clock's
* frequency to be changed while it is running so long as it
* is within the min/max limits.
* MSG_FLAG_CLOCK_INPUT_TERM: Enable input termination, this
* is only applicable to clock inputs on the SoC pseudo-device.
* @dev_id: Device identifier this request is for
* @clk_id: Clock identifier for the device for this request.
* Each device has it's own set of clock inputs. This indexes
* which clock input to modify. Set to 255 if clock ID is
* greater than or equal to 255.
* @request_state: Request the state for the clock to be set to.
* MSG_CLOCK_SW_STATE_UNREQ: The IP does not require this clock,
* it can be disabled, regardless of the state of the device
* MSG_CLOCK_SW_STATE_AUTO: Allow the System Controller to
* automatically manage the state of this clock. If the device
* is enabled, then the clock is enabled. If the device is set
* to off or retention, then the clock is internally set as not
* being required by the device.(default)
* MSG_CLOCK_SW_STATE_REQ: Configure the clock to be enabled,
* regardless of the state of the device.
* @clk_id_32: Clock identifier for the device for this request.
* Only to be used if the clock ID is greater than or equal to
* 255.
*
* Normally, all required clocks are managed by TISCI entity, this is used
* only for specific control *IF* required. Auto managed state is
* MSG_CLOCK_SW_STATE_AUTO, in other states, TISCI entity assume remote
* will explicitly control.
*
* Request type is TI_SCI_MSG_SET_CLOCK_STATE, response is a generic
* ACK or NACK message.
*/
struct ti_sci_msg_req_set_clock_state {
/* Additional hdr->flags options */
#define MSG_FLAG_CLOCK_ALLOW_SSC TI_SCI_MSG_FLAG(8)
#define MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE TI_SCI_MSG_FLAG(9)
#define MSG_FLAG_CLOCK_INPUT_TERM TI_SCI_MSG_FLAG(10)
struct ti_sci_msg_hdr hdr;
u32 dev_id;
u8 clk_id;
#define MSG_CLOCK_SW_STATE_UNREQ 0
#define MSG_CLOCK_SW_STATE_AUTO 1
#define MSG_CLOCK_SW_STATE_REQ 2
u8 request_state;
u32 clk_id_32;
} __packed;
/**
* struct ti_sci_msg_req_get_clock_state - Request for clock state
* @hdr: Generic Header
* @dev_id: Device identifier this request is for
* @clk_id: Clock identifier for the device for this request.
* Each device has it's own set of clock inputs. This indexes
* which clock input to get state of. Set to 255 if the clock
* ID is greater than or equal to 255.
* @clk_id_32: Clock identifier for the device for the request.
* Only to be used if the clock ID is greater than or equal to
* 255.
*
* Request type is TI_SCI_MSG_GET_CLOCK_STATE, response is state
* of the clock
*/
struct ti_sci_msg_req_get_clock_state {
struct ti_sci_msg_hdr hdr;
u32 dev_id;
u8 clk_id;
u32 clk_id_32;
} __packed;
/**
* struct ti_sci_msg_resp_get_clock_state - Response to get clock state
* @hdr: Generic Header
* @programmed_state: Any programmed state of the clock. This is one of
* MSG_CLOCK_SW_STATE* values.
* @current_state: Current state of the clock. This is one of:
* MSG_CLOCK_HW_STATE_NOT_READY: Clock is not ready
* MSG_CLOCK_HW_STATE_READY: Clock is ready
*
* Response to TI_SCI_MSG_GET_CLOCK_STATE.
*/
struct ti_sci_msg_resp_get_clock_state {
struct ti_sci_msg_hdr hdr;
u8 programmed_state;
#define MSG_CLOCK_HW_STATE_NOT_READY 0
#define MSG_CLOCK_HW_STATE_READY 1
u8 current_state;
} __packed;
/**
* struct ti_sci_msg_req_set_clock_parent - Set the clock parent
* @hdr: Generic Header
* @dev_id: Device identifier this request is for
* @clk_id: Clock identifier for the device for this request.
* Each device has it's own set of clock inputs. This indexes
* which clock input to modify. Set to 255 if clock ID is
* greater than or equal to 255.
* @parent_id: The new clock parent is selectable by an index via this
* parameter. Set to 255 if clock ID is greater than or
* equal to 255.
* @clk_id_32: Clock identifier if @clk_id field is 255.
* @parent_id_32: Parent identifier if @parent_id is 255.
*
* Request type is TI_SCI_MSG_SET_CLOCK_PARENT, response is generic
* ACK / NACK message.
*/
struct ti_sci_msg_req_set_clock_parent {
struct ti_sci_msg_hdr hdr;
u32 dev_id;
u8 clk_id;
u8 parent_id;
u32 clk_id_32;
u32 parent_id_32;
} __packed;
/**
* struct ti_sci_msg_req_get_clock_parent - Get the clock parent
* @hdr: Generic Header
* @dev_id: Device identifier this request is for
* @clk_id: Clock identifier for the device for this request.
* Each device has it's own set of clock inputs. This indexes
* which clock input to get the parent for. If this field
* contains 255, the actual clock identifier is stored in
* @clk_id_32.
* @clk_id_32: Clock identifier if the @clk_id field contains 255.
*
* Request type is TI_SCI_MSG_GET_CLOCK_PARENT, response is parent information
*/
struct ti_sci_msg_req_get_clock_parent {
struct ti_sci_msg_hdr hdr;
u32 dev_id;
u8 clk_id;
u32 clk_id_32;
} __packed;
/**
* struct ti_sci_msg_resp_get_clock_parent - Response with clock parent
* @hdr: Generic Header
* @parent_id: The current clock parent. If set to 255, the current parent
* ID can be found from the @parent_id_32 field.
* @parent_id_32: Current clock parent if @parent_id field is set to
* 255.
*
* Response to TI_SCI_MSG_GET_CLOCK_PARENT.
*/
struct ti_sci_msg_resp_get_clock_parent {
struct ti_sci_msg_hdr hdr;
u8 parent_id;
u32 parent_id_32;
} __packed;
/**
* struct ti_sci_msg_req_get_clock_num_parents - Request to get clock parents
* @hdr: Generic header
* @dev_id: Device identifier this request is for
* @clk_id: Clock identifier for the device for this request. Set to
* 255 if clock ID is greater than or equal to 255.
* @clk_id_32: Clock identifier if the @clk_id field contains 255.
*
* This request provides information about how many clock parent options
* are available for a given clock to a device. This is typically used
* for input clocks.
*
* Request type is TI_SCI_MSG_GET_NUM_CLOCK_PARENTS, response is appropriate
* message, or NACK in case of inability to satisfy request.
*/
struct ti_sci_msg_req_get_clock_num_parents {
struct ti_sci_msg_hdr hdr;
u32 dev_id;
u8 clk_id;
u32 clk_id_32;
} __packed;
/**
* struct ti_sci_msg_resp_get_clock_num_parents - Response for get clk parents
* @hdr: Generic header
* @num_parents: Number of clock parents. If set to 255, the actual
* number of parents is stored into @num_parents_32
* field instead.
* @num_parents_32: Number of clock parents if @num_parents field is
* set to 255.
*
* Response to TI_SCI_MSG_GET_NUM_CLOCK_PARENTS
*/
struct ti_sci_msg_resp_get_clock_num_parents {
struct ti_sci_msg_hdr hdr;
u8 num_parents;
u32 num_parents_32;
} __packed;
/**
* struct ti_sci_msg_req_query_clock_freq - Request to query a frequency
* @hdr: Generic Header
* @dev_id: Device identifier this request is for
* @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum
* allowable programmed frequency and does not account for clock
* tolerances and jitter.
* @target_freq_hz: The target clock frequency. A frequency will be found
* as close to this target frequency as possible.
* @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum
* allowable programmed frequency and does not account for clock
* tolerances and jitter.
* @clk_id: Clock identifier for the device for this request. Set to
* 255 if clock identifier is greater than or equal to 255.
* @clk_id_32: Clock identifier if @clk_id is set to 255.
*
* NOTE: Normally clock frequency management is automatically done by TISCI
* entity. In case of specific requests, TISCI evaluates capability to achieve
* requested frequency within provided range and responds with
* result message.
*
* Request type is TI_SCI_MSG_QUERY_CLOCK_FREQ, response is appropriate message,
* or NACK in case of inability to satisfy request.
*/
struct ti_sci_msg_req_query_clock_freq {
struct ti_sci_msg_hdr hdr;
u32 dev_id;
u64 min_freq_hz;
u64 target_freq_hz;
u64 max_freq_hz;
u8 clk_id;
u32 clk_id_32;
} __packed;
/**
* struct ti_sci_msg_resp_query_clock_freq - Response to a clock frequency query
* @hdr: Generic Header
* @freq_hz: Frequency that is the best match in Hz.
*
* Response to request type TI_SCI_MSG_QUERY_CLOCK_FREQ. NOTE: if the request
* cannot be satisfied, the message will be of type NACK.
*/
struct ti_sci_msg_resp_query_clock_freq {
struct ti_sci_msg_hdr hdr;
u64 freq_hz;
} __packed;
/**
* struct ti_sci_msg_req_set_clock_freq - Request to setup a clock frequency
* @hdr: Generic Header
* @dev_id: Device identifier this request is for
* @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum
* allowable programmed frequency and does not account for clock
* tolerances and jitter.
* @target_freq_hz: The target clock frequency. The clock will be programmed
* at a rate as close to this target frequency as possible.
* @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum
* allowable programmed frequency and does not account for clock
* tolerances and jitter.
* @clk_id: Clock identifier for the device for this request. Set to
* 255 if clock ID is greater than or equal to 255.
* @clk_id_32: Clock identifier if @clk_id field is set to 255.
*
* NOTE: Normally clock frequency management is automatically done by TISCI
* entity. In case of specific requests, TISCI evaluates capability to achieve
* requested range and responds with success/failure message.
*
* This sets the desired frequency for a clock within an allowable
* range. This message will fail on an enabled clock unless
* MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE is set for the clock. Additionally,
* if other clocks have their frequency modified due to this message,
* they also must have the MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE or be disabled.
*
* Calling set frequency on a clock input to the SoC pseudo-device will
* inform the PMMC of that clock's frequency. Setting a frequency of
* zero will indicate the clock is disabled.
*
* Calling set frequency on clock outputs from the SoC pseudo-device will
* function similarly to setting the clock frequency on a device.
*
* Request type is TI_SCI_MSG_SET_CLOCK_FREQ, response is a generic ACK/NACK
* message.
*/
struct ti_sci_msg_req_set_clock_freq {
struct ti_sci_msg_hdr hdr;
u32 dev_id;
u64 min_freq_hz;
u64 target_freq_hz;
u64 max_freq_hz;
u8 clk_id;
u32 clk_id_32;
} __packed;
/**
* struct ti_sci_msg_req_get_clock_freq - Request to get the clock frequency
* @hdr: Generic Header
* @dev_id: Device identifier this request is for
* @clk_id: Clock identifier for the device for this request. Set to
* 255 if clock ID is greater than or equal to 255.
* @clk_id_32: Clock identifier if @clk_id field is set to 255.
*
* NOTE: Normally clock frequency management is automatically done by TISCI
* entity. In some cases, clock frequencies are configured by host.
*
* Request type is TI_SCI_MSG_GET_CLOCK_FREQ, responded with clock frequency
* that the clock is currently at.
*/
struct ti_sci_msg_req_get_clock_freq {
struct ti_sci_msg_hdr hdr;
u32 dev_id;
u8 clk_id;
u32 clk_id_32;
} __packed;
/**
* struct ti_sci_msg_resp_get_clock_freq - Response of clock frequency request
* @hdr: Generic Header
* @freq_hz: Frequency that the clock is currently on, in Hz.
*
* Response to request type TI_SCI_MSG_GET_CLOCK_FREQ.
*/
struct ti_sci_msg_resp_get_clock_freq {
struct ti_sci_msg_hdr hdr;
u64 freq_hz;
} __packed;
#define TI_SCI_IRQ_SECONDARY_HOST_INVALID 0xff
/**
* struct ti_sci_msg_req_get_resource_range - Request to get a host's assigned
* range of resources.
* @hdr: Generic Header
* @type: Unique resource assignment type
* @subtype: Resource assignment subtype within the resource type.
* @secondary_host: Host processing entity to which the resources are
* allocated. This is required only when the destination
* host id id different from ti sci interface host id,
* else TI_SCI_IRQ_SECONDARY_HOST_INVALID can be passed.
*
* Request type is TI_SCI_MSG_GET_RESOURCE_RANGE. Responded with requested
* resource range which is of type TI_SCI_MSG_GET_RESOURCE_RANGE.
*/
struct ti_sci_msg_req_get_resource_range {
struct ti_sci_msg_hdr hdr;
#define MSG_RM_RESOURCE_TYPE_MASK GENMASK(9, 0)
#define MSG_RM_RESOURCE_SUBTYPE_MASK GENMASK(5, 0)
u16 type;
u8 subtype;
u8 secondary_host;
} __packed;
/**
* struct ti_sci_msg_resp_get_resource_range - Response to resource get range.
* @hdr: Generic Header
* @range_start: Start index of the resource range.
* @range_num: Number of resources in the range.
*
* Response to request TI_SCI_MSG_GET_RESOURCE_RANGE.
*/
struct ti_sci_msg_resp_get_resource_range {
struct ti_sci_msg_hdr hdr;
u16 range_start;
u16 range_num;
} __packed;
/**
* struct ti_sci_msg_req_manage_irq - Request to configure/release the route
* between the dev and the host.
* @hdr: Generic Header
* @valid_params: Bit fields defining the validity of interrupt source
* parameters. If a bit is not set, then corresponding
* field is not valid and will not be used for route set.
* Bit field definitions:
* 0 - Valid bit for @dst_id
* 1 - Valid bit for @dst_host_irq
* 2 - Valid bit for @ia_id
* 3 - Valid bit for @vint
* 4 - Valid bit for @global_event
* 5 - Valid bit for @vint_status_bit_index
* 31 - Valid bit for @secondary_host
* @src_id: IRQ source peripheral ID.
* @src_index: IRQ source index within the peripheral
* @dst_id: IRQ Destination ID. Based on the architecture it can be
* IRQ controller or host processor ID.
* @dst_host_irq: IRQ number of the destination host IRQ controller
* @ia_id: Device ID of the interrupt aggregator in which the
* vint resides.
* @vint: Virtual interrupt number if the interrupt route
* is through an interrupt aggregator.
* @global_event: Global event that is to be mapped to interrupt
* aggregator virtual interrupt status bit.
* @vint_status_bit: Virtual interrupt status bit if the interrupt route
* utilizes an interrupt aggregator status bit.
* @secondary_host: Host ID of the IRQ destination computing entity. This is
* required only when destination host id is different
* from ti sci interface host id.
*
* Request type is TI_SCI_MSG_SET/RELEASE_IRQ.
* Response is generic ACK / NACK message.
*/
struct ti_sci_msg_req_manage_irq {
struct ti_sci_msg_hdr hdr;
#define MSG_FLAG_DST_ID_VALID TI_SCI_MSG_FLAG(0)
#define MSG_FLAG_DST_HOST_IRQ_VALID TI_SCI_MSG_FLAG(1)
#define MSG_FLAG_IA_ID_VALID TI_SCI_MSG_FLAG(2)
#define MSG_FLAG_VINT_VALID TI_SCI_MSG_FLAG(3)
#define MSG_FLAG_GLB_EVNT_VALID TI_SCI_MSG_FLAG(4)
#define MSG_FLAG_VINT_STS_BIT_VALID TI_SCI_MSG_FLAG(5)
#define MSG_FLAG_SHOST_VALID TI_SCI_MSG_FLAG(31)
u32 valid_params;
u16 src_id;
u16 src_index;
u16 dst_id;
u16 dst_host_irq;
u16 ia_id;
u16 vint;
u16 global_event;
u8 vint_status_bit;
u8 secondary_host;
} __packed;
/**
* struct ti_sci_msg_rm_ring_cfg_req - Configure a Navigator Subsystem ring
*
* Configures the non-real-time registers of a Navigator Subsystem ring.
* @hdr: Generic Header
* @valid_params: Bitfield defining validity of ring configuration parameters.
* The ring configuration fields are not valid, and will not be used for
* ring configuration, if their corresponding valid bit is zero.
* Valid bit usage:
* 0 - Valid bit for @tisci_msg_rm_ring_cfg_req addr_lo
* 1 - Valid bit for @tisci_msg_rm_ring_cfg_req addr_hi
* 2 - Valid bit for @tisci_msg_rm_ring_cfg_req count
* 3 - Valid bit for @tisci_msg_rm_ring_cfg_req mode
* 4 - Valid bit for @tisci_msg_rm_ring_cfg_req size
* 5 - Valid bit for @tisci_msg_rm_ring_cfg_req order_id
* @nav_id: Device ID of Navigator Subsystem from which the ring is allocated
* @index: ring index to be configured.
* @addr_lo: 32 LSBs of ring base address to be programmed into the ring's
* RING_BA_LO register
* @addr_hi: 16 MSBs of ring base address to be programmed into the ring's
* RING_BA_HI register.
* @count: Number of ring elements. Must be even if mode is CREDENTIALS or QM
* modes.
* @mode: Specifies the mode the ring is to be configured.
* @size: Specifies encoded ring element size. To calculate the encoded size use
* the formula (log2(size_bytes) - 2), where size_bytes cannot be
* greater than 256.
* @order_id: Specifies the ring's bus order ID.
*/
struct ti_sci_msg_rm_ring_cfg_req {
struct ti_sci_msg_hdr hdr;
u32 valid_params;
u16 nav_id;
u16 index;
u32 addr_lo;
u32 addr_hi;
u32 count;
u8 mode;
u8 size;
u8 order_id;
} __packed;
/**
* struct ti_sci_msg_rm_ring_get_cfg_req - Get RA ring's configuration
*
* Gets the configuration of the non-real-time register fields of a ring. The
* host, or a supervisor of the host, who owns the ring must be the requesting
* host. The values of the non-real-time registers are returned in
* @ti_sci_msg_rm_ring_get_cfg_resp.
*
* @hdr: Generic Header
* @nav_id: Device ID of Navigator Subsystem from which the ring is allocated
* @index: ring index.
*/
struct ti_sci_msg_rm_ring_get_cfg_req {
struct ti_sci_msg_hdr hdr;
u16 nav_id;
u16 index;
} __packed;
/**
* struct ti_sci_msg_rm_ring_get_cfg_resp - Ring get configuration response
*
* Response received by host processor after RM has handled
* @ti_sci_msg_rm_ring_get_cfg_req. The response contains the ring's
* non-real-time register values.
*
* @hdr: Generic Header
* @addr_lo: Ring 32 LSBs of base address
* @addr_hi: Ring 16 MSBs of base address.
* @count: Ring number of elements.
* @mode: Ring mode.
* @size: encoded Ring element size
* @order_id: ing order ID.
*/
struct ti_sci_msg_rm_ring_get_cfg_resp {
struct ti_sci_msg_hdr hdr;
u32 addr_lo;
u32 addr_hi;
u32 count;
u8 mode;
u8 size;
u8 order_id;
} __packed;
/**
* struct ti_sci_msg_psil_pair - Pairs a PSI-L source thread to a destination
* thread
* @hdr: Generic Header
* @nav_id: SoC Navigator Subsystem device ID whose PSI-L config proxy is
* used to pair the source and destination threads.
* @src_thread: PSI-L source thread ID within the PSI-L System thread map.
*
* UDMAP transmit channels mapped to source threads will have their
* TCHAN_THRD_ID register programmed with the destination thread if the pairing
* is successful.
* @dst_thread: PSI-L destination thread ID within the PSI-L System thread map.
* PSI-L destination threads start at index 0x8000. The request is NACK'd if
* the destination thread is not greater than or equal to 0x8000.
*
* UDMAP receive channels mapped to destination threads will have their
* RCHAN_THRD_ID register programmed with the source thread if the pairing
* is successful.
*
* Request type is TI_SCI_MSG_RM_PSIL_PAIR, response is a generic ACK or NACK
* message.
*/
struct ti_sci_msg_psil_pair {
struct ti_sci_msg_hdr hdr;
u32 nav_id;
u32 src_thread;
u32 dst_thread;
} __packed;
/**
* struct ti_sci_msg_psil_unpair - Unpairs a PSI-L source thread from a
* destination thread
* @hdr: Generic Header
* @nav_id: SoC Navigator Subsystem device ID whose PSI-L config proxy is
* used to unpair the source and destination threads.
* @src_thread: PSI-L source thread ID within the PSI-L System thread map.
*
* UDMAP transmit channels mapped to source threads will have their
* TCHAN_THRD_ID register cleared if the unpairing is successful.
*
* @dst_thread: PSI-L destination thread ID within the PSI-L System thread map.
* PSI-L destination threads start at index 0x8000. The request is NACK'd if
* the destination thread is not greater than or equal to 0x8000.
*
* UDMAP receive channels mapped to destination threads will have their
* RCHAN_THRD_ID register cleared if the unpairing is successful.
*
* Request type is TI_SCI_MSG_RM_PSIL_UNPAIR, response is a generic ACK or NACK
* message.
*/
struct ti_sci_msg_psil_unpair {
struct ti_sci_msg_hdr hdr;
u32 nav_id;
u32 src_thread;
u32 dst_thread;
} __packed;
/**
* struct ti_sci_msg_udmap_rx_flow_cfg - UDMAP receive flow configuration
* message
* @hdr: Generic Header
* @nav_id: SoC Navigator Subsystem device ID from which the receive flow is
* allocated
* @flow_index: UDMAP receive flow index for non-optional configuration.
* @rx_ch_index: Specifies the index of the receive channel using the flow_index
* @rx_einfo_present: UDMAP receive flow extended packet info present.
* @rx_psinfo_present: UDMAP receive flow PS words present.
* @rx_error_handling: UDMAP receive flow error handling configuration. Valid
* values are TI_SCI_RM_UDMAP_RX_FLOW_ERR_DROP/RETRY.
* @rx_desc_type: UDMAP receive flow descriptor type. It can be one of
* TI_SCI_RM_UDMAP_RX_FLOW_DESC_HOST/MONO.
* @rx_sop_offset: UDMAP receive flow start of packet offset.
* @rx_dest_qnum: UDMAP receive flow destination queue number.
* @rx_ps_location: UDMAP receive flow PS words location.
* 0 - end of packet descriptor
* 1 - Beginning of the data buffer
* @rx_src_tag_hi: UDMAP receive flow source tag high byte constant
* @rx_src_tag_lo: UDMAP receive flow source tag low byte constant
* @rx_dest_tag_hi: UDMAP receive flow destination tag high byte constant
* @rx_dest_tag_lo: UDMAP receive flow destination tag low byte constant
* @rx_src_tag_hi_sel: UDMAP receive flow source tag high byte selector
* @rx_src_tag_lo_sel: UDMAP receive flow source tag low byte selector
* @rx_dest_tag_hi_sel: UDMAP receive flow destination tag high byte selector
* @rx_dest_tag_lo_sel: UDMAP receive flow destination tag low byte selector
* @rx_size_thresh_en: UDMAP receive flow packet size based free buffer queue
* enable. If enabled, the ti_sci_rm_udmap_rx_flow_opt_cfg also need to be
* configured and sent.
* @rx_fdq0_sz0_qnum: UDMAP receive flow free descriptor queue 0.
* @rx_fdq1_qnum: UDMAP receive flow free descriptor queue 1.
* @rx_fdq2_qnum: UDMAP receive flow free descriptor queue 2.
* @rx_fdq3_qnum: UDMAP receive flow free descriptor queue 3.
*
* For detailed information on the settings, see the UDMAP section of the TRM.
*/
struct ti_sci_msg_udmap_rx_flow_cfg {
struct ti_sci_msg_hdr hdr;
u32 nav_id;
u32 flow_index;
u32 rx_ch_index;
u8 rx_einfo_present;
u8 rx_psinfo_present;
u8 rx_error_handling;
u8 rx_desc_type;
u16 rx_sop_offset;
u16 rx_dest_qnum;
u8 rx_ps_location;
u8 rx_src_tag_hi;
u8 rx_src_tag_lo;
u8 rx_dest_tag_hi;
u8 rx_dest_tag_lo;
u8 rx_src_tag_hi_sel;
u8 rx_src_tag_lo_sel;
u8 rx_dest_tag_hi_sel;
u8 rx_dest_tag_lo_sel;
u8 rx_size_thresh_en;
u16 rx_fdq0_sz0_qnum;
u16 rx_fdq1_qnum;
u16 rx_fdq2_qnum;
u16 rx_fdq3_qnum;
} __packed;
/**
* struct rm_ti_sci_msg_udmap_rx_flow_opt_cfg - parameters for UDMAP receive
* flow optional configuration
* @hdr: Generic Header
* @nav_id: SoC Navigator Subsystem device ID from which the receive flow is
* allocated
* @flow_index: UDMAP receive flow index for optional configuration.
* @rx_ch_index: Specifies the index of the receive channel using the flow_index
* @rx_size_thresh0: UDMAP receive flow packet size threshold 0.
* @rx_size_thresh1: UDMAP receive flow packet size threshold 1.
* @rx_size_thresh2: UDMAP receive flow packet size threshold 2.
* @rx_fdq0_sz1_qnum: UDMAP receive flow free descriptor queue for size
* threshold 1.
* @rx_fdq0_sz2_qnum: UDMAP receive flow free descriptor queue for size
* threshold 2.
* @rx_fdq0_sz3_qnum: UDMAP receive flow free descriptor queue for size
* threshold 3.
*
* For detailed information on the settings, see the UDMAP section of the TRM.
*/
struct rm_ti_sci_msg_udmap_rx_flow_opt_cfg {
struct ti_sci_msg_hdr hdr;
u32 nav_id;
u32 flow_index;
u32 rx_ch_index;
u16 rx_size_thresh0;
u16 rx_size_thresh1;
u16 rx_size_thresh2;
u16 rx_fdq0_sz1_qnum;
u16 rx_fdq0_sz2_qnum;
u16 rx_fdq0_sz3_qnum;
} __packed;
/**
* Configures a Navigator Subsystem UDMAP transmit channel
*
* Configures the non-real-time registers of a Navigator Subsystem UDMAP
* transmit channel. The channel index must be assigned to the host defined
* in the TISCI header via the RM board configuration resource assignment
* range list.
*
* @hdr: Generic Header
*
* @valid_params: Bitfield defining validity of tx channel configuration
* parameters. The tx channel configuration fields are not valid, and will not
* be used for ch configuration, if their corresponding valid bit is zero.
* Valid bit usage:
* 0 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_pause_on_err
* 1 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_atype
* 2 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_chan_type
* 3 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_fetch_size
* 4 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::txcq_qnum
* 5 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_priority
* 6 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_qos
* 7 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_orderid
* 8 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_sched_priority
* 9 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_filt_einfo
* 10 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_filt_pswords
* 11 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_supr_tdpkt
* 12 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_credit_count
* 13 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::fdepth
* 14 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_burst_size
*
* @nav_id: SoC device ID of Navigator Subsystem where tx channel is located
*
* @index: UDMAP transmit channel index.
*
* @tx_pause_on_err: UDMAP transmit channel pause on error configuration to
* be programmed into the tx_pause_on_err field of the channel's TCHAN_TCFG
* register.
*
* @tx_filt_einfo: UDMAP transmit channel extended packet information passing
* configuration to be programmed into the tx_filt_einfo field of the
* channel's TCHAN_TCFG register.
*
* @tx_filt_pswords: UDMAP transmit channel protocol specific word passing
* configuration to be programmed into the tx_filt_pswords field of the
* channel's TCHAN_TCFG register.
*
* @tx_atype: UDMAP transmit channel non Ring Accelerator access pointer
* interpretation configuration to be programmed into the tx_atype field of
* the channel's TCHAN_TCFG register.
*
* @tx_chan_type: UDMAP transmit channel functional channel type and work
* passing mechanism configuration to be programmed into the tx_chan_type
* field of the channel's TCHAN_TCFG register.
*
* @tx_supr_tdpkt: UDMAP transmit channel teardown packet generation suppression
* configuration to be programmed into the tx_supr_tdpkt field of the channel's
* TCHAN_TCFG register.
*
* @tx_fetch_size: UDMAP transmit channel number of 32-bit descriptor words to
* fetch configuration to be programmed into the tx_fetch_size field of the
* channel's TCHAN_TCFG register. The user must make sure to set the maximum
* word count that can pass through the channel for any allowed descriptor type.
*
* @tx_credit_count: UDMAP transmit channel transfer request credit count
* configuration to be programmed into the count field of the TCHAN_TCREDIT
* register. Specifies how many credits for complete TRs are available.
*
* @txcq_qnum: UDMAP transmit channel completion queue configuration to be
* programmed into the txcq_qnum field of the TCHAN_TCQ register. The specified
* completion queue must be assigned to the host, or a subordinate of the host,
* requesting configuration of the transmit channel.
*
* @tx_priority: UDMAP transmit channel transmit priority value to be programmed
* into the priority field of the channel's TCHAN_TPRI_CTRL register.
*
* @tx_qos: UDMAP transmit channel transmit qos value to be programmed into the
* qos field of the channel's TCHAN_TPRI_CTRL register.
*
* @tx_orderid: UDMAP transmit channel bus order id value to be programmed into
* the orderid field of the channel's TCHAN_TPRI_CTRL register.
*
* @fdepth: UDMAP transmit channel FIFO depth configuration to be programmed
* into the fdepth field of the TCHAN_TFIFO_DEPTH register. Sets the number of
* Tx FIFO bytes which are allowed to be stored for the channel. Check the UDMAP
* section of the TRM for restrictions regarding this parameter.
*
* @tx_sched_priority: UDMAP transmit channel tx scheduling priority
* configuration to be programmed into the priority field of the channel's
* TCHAN_TST_SCHED register.
*
* @tx_burst_size: UDMAP transmit channel burst size configuration to be
* programmed into the tx_burst_size field of the TCHAN_TCFG register.
*/
struct ti_sci_msg_rm_udmap_tx_ch_cfg_req {
struct ti_sci_msg_hdr hdr;
u32 valid_params;
u16 nav_id;
u16 index;
u8 tx_pause_on_err;
u8 tx_filt_einfo;
u8 tx_filt_pswords;
u8 tx_atype;
u8 tx_chan_type;
u8 tx_supr_tdpkt;
u16 tx_fetch_size;
u8 tx_credit_count;
u16 txcq_qnum;
u8 tx_priority;
u8 tx_qos;
u8 tx_orderid;
u16 fdepth;
u8 tx_sched_priority;
u8 tx_burst_size;
} __packed;
/**
* Configures a Navigator Subsystem UDMAP receive channel
*
* Configures the non-real-time registers of a Navigator Subsystem UDMAP
* receive channel. The channel index must be assigned to the host defined
* in the TISCI header via the RM board configuration resource assignment
* range list.
*
* @hdr: Generic Header
*
* @valid_params: Bitfield defining validity of rx channel configuration
* parameters.
* The rx channel configuration fields are not valid, and will not be used for
* ch configuration, if their corresponding valid bit is zero.
* Valid bit usage:
* 0 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_pause_on_err
* 1 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_atype
* 2 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_chan_type
* 3 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_fetch_size
* 4 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rxcq_qnum
* 5 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_priority
* 6 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_qos
* 7 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_orderid
* 8 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_sched_priority
* 9 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::flowid_start
* 10 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::flowid_cnt
* 11 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_ignore_short
* 12 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_ignore_long
* 14 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_burst_size
*
* @nav_id: SoC device ID of Navigator Subsystem where rx channel is located
*
* @index: UDMAP receive channel index.
*
* @rx_fetch_size: UDMAP receive channel number of 32-bit descriptor words to
* fetch configuration to be programmed into the rx_fetch_size field of the
* channel's RCHAN_RCFG register.
*
* @rxcq_qnum: UDMAP receive channel completion queue configuration to be
* programmed into the rxcq_qnum field of the RCHAN_RCQ register.
* The specified completion queue must be assigned to the host, or a subordinate
* of the host, requesting configuration of the receive channel.
*
* @rx_priority: UDMAP receive channel receive priority value to be programmed
* into the priority field of the channel's RCHAN_RPRI_CTRL register.
*
* @rx_qos: UDMAP receive channel receive qos value to be programmed into the
* qos field of the channel's RCHAN_RPRI_CTRL register.
*
* @rx_orderid: UDMAP receive channel bus order id value to be programmed into
* the orderid field of the channel's RCHAN_RPRI_CTRL register.
*
* @rx_sched_priority: UDMAP receive channel rx scheduling priority
* configuration to be programmed into the priority field of the channel's
* RCHAN_RST_SCHED register.
*
* @flowid_start: UDMAP receive channel additional flows starting index
* configuration to program into the flow_start field of the RCHAN_RFLOW_RNG
* register. Specifies the starting index for flow IDs the receive channel is to
* make use of beyond the default flow. flowid_start and @ref flowid_cnt must be
* set as valid and configured together. The starting flow ID set by
* @ref flowid_cnt must be a flow index within the Navigator Subsystem's subset
* of flows beyond the default flows statically mapped to receive channels.
* The additional flows must be assigned to the host, or a subordinate of the
* host, requesting configuration of the receive channel.
*
* @flowid_cnt: UDMAP receive channel additional flows count configuration to
* program into the flowid_cnt field of the RCHAN_RFLOW_RNG register.
* This field specifies how many flow IDs are in the additional contiguous range
* of legal flow IDs for the channel. @ref flowid_start and flowid_cnt must be
* set as valid and configured together. Disabling the valid_params field bit
* for flowid_cnt indicates no flow IDs other than the default are to be
* allocated and used by the receive channel. @ref flowid_start plus flowid_cnt
* cannot be greater than the number of receive flows in the receive channel's
* Navigator Subsystem. The additional flows must be assigned to the host, or a
* subordinate of the host, requesting configuration of the receive channel.
*
* @rx_pause_on_err: UDMAP receive channel pause on error configuration to be
* programmed into the rx_pause_on_err field of the channel's RCHAN_RCFG
* register.
*
* @rx_atype: UDMAP receive channel non Ring Accelerator access pointer
* interpretation configuration to be programmed into the rx_atype field of the
* channel's RCHAN_RCFG register.
*
* @rx_chan_type: UDMAP receive channel functional channel type and work passing
* mechanism configuration to be programmed into the rx_chan_type field of the
* channel's RCHAN_RCFG register.
*
* @rx_ignore_short: UDMAP receive channel short packet treatment configuration
* to be programmed into the rx_ignore_short field of the RCHAN_RCFG register.
*
* @rx_ignore_long: UDMAP receive channel long packet treatment configuration to
* be programmed into the rx_ignore_long field of the RCHAN_RCFG register.
*
* @rx_burst_size: UDMAP receive channel burst size configuration to be
* programmed into the rx_burst_size field of the RCHAN_RCFG register.
*/
struct ti_sci_msg_rm_udmap_rx_ch_cfg_req {
struct ti_sci_msg_hdr hdr;
u32 valid_params;
u16 nav_id;
u16 index;
u16 rx_fetch_size;
u16 rxcq_qnum;
u8 rx_priority;
u8 rx_qos;
u8 rx_orderid;
u8 rx_sched_priority;
u16 flowid_start;
u16 flowid_cnt;
u8 rx_pause_on_err;
u8 rx_atype;
u8 rx_chan_type;
u8 rx_ignore_short;
u8 rx_ignore_long;
u8 rx_burst_size;
} __packed;
/**
* Configures a Navigator Subsystem UDMAP receive flow
*
* Configures a Navigator Subsystem UDMAP receive flow's registers.
* Configuration does not include the flow registers which handle size-based
* free descriptor queue routing.
*
* The flow index must be assigned to the host defined in the TISCI header via
* the RM board configuration resource assignment range list.
*
* @hdr: Standard TISCI header
*
* @valid_params
* Bitfield defining validity of rx flow configuration parameters. The
* rx flow configuration fields are not valid, and will not be used for flow
* configuration, if their corresponding valid bit is zero. Valid bit usage:
* 0 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_einfo_present
* 1 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_psinfo_present
* 2 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_error_handling
* 3 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_desc_type
* 4 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_sop_offset
* 5 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_qnum
* 6 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_hi
* 7 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_lo
* 8 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_hi
* 9 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_lo
* 10 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_hi_sel
* 11 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_lo_sel
* 12 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_hi_sel
* 13 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_lo_sel
* 14 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq0_sz0_qnum
* 15 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq1_sz0_qnum
* 16 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq2_sz0_qnum
* 17 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq3_sz0_qnum
* 18 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_ps_location
*
* @nav_id: SoC device ID of Navigator Subsystem from which the receive flow is
* allocated
*
* @flow_index: UDMAP receive flow index for non-optional configuration.
*
* @rx_einfo_present:
* UDMAP receive flow extended packet info present configuration to be
* programmed into the rx_einfo_present field of the flow's RFLOW_RFA register.
*
* @rx_psinfo_present:
* UDMAP receive flow PS words present configuration to be programmed into the
* rx_psinfo_present field of the flow's RFLOW_RFA register.
*
* @rx_error_handling:
* UDMAP receive flow error handling configuration to be programmed into the
* rx_error_handling field of the flow's RFLOW_RFA register.
*
* @rx_desc_type:
* UDMAP receive flow descriptor type configuration to be programmed into the
* rx_desc_type field field of the flow's RFLOW_RFA register.
*
* @rx_sop_offset:
* UDMAP receive flow start of packet offset configuration to be programmed
* into the rx_sop_offset field of the RFLOW_RFA register. See the UDMAP
* section of the TRM for more information on this setting. Valid values for
* this field are 0-255 bytes.
*
* @rx_dest_qnum:
* UDMAP receive flow destination queue configuration to be programmed into the
* rx_dest_qnum field of the flow's RFLOW_RFA register. The specified
* destination queue must be valid within the Navigator Subsystem and must be
* owned by the host, or a subordinate of the host, requesting allocation and
* configuration of the receive flow.
*
* @rx_src_tag_hi:
* UDMAP receive flow source tag high byte constant configuration to be
* programmed into the rx_src_tag_hi field of the flow's RFLOW_RFB register.
* See the UDMAP section of the TRM for more information on this setting.
*
* @rx_src_tag_lo:
* UDMAP receive flow source tag low byte constant configuration to be
* programmed into the rx_src_tag_lo field of the flow's RFLOW_RFB register.
* See the UDMAP section of the TRM for more information on this setting.
*
* @rx_dest_tag_hi:
* UDMAP receive flow destination tag high byte constant configuration to be
* programmed into the rx_dest_tag_hi field of the flow's RFLOW_RFB register.
* See the UDMAP section of the TRM for more information on this setting.
*
* @rx_dest_tag_lo:
* UDMAP receive flow destination tag low byte constant configuration to be
* programmed into the rx_dest_tag_lo field of the flow's RFLOW_RFB register.
* See the UDMAP section of the TRM for more information on this setting.
*
* @rx_src_tag_hi_sel:
* UDMAP receive flow source tag high byte selector configuration to be
* programmed into the rx_src_tag_hi_sel field of the RFLOW_RFC register. See
* the UDMAP section of the TRM for more information on this setting.
*
* @rx_src_tag_lo_sel:
* UDMAP receive flow source tag low byte selector configuration to be
* programmed into the rx_src_tag_lo_sel field of the RFLOW_RFC register. See
* the UDMAP section of the TRM for more information on this setting.
*
* @rx_dest_tag_hi_sel:
* UDMAP receive flow destination tag high byte selector configuration to be
* programmed into the rx_dest_tag_hi_sel field of the RFLOW_RFC register. See
* the UDMAP section of the TRM for more information on this setting.
*
* @rx_dest_tag_lo_sel:
* UDMAP receive flow destination tag low byte selector configuration to be
* programmed into the rx_dest_tag_lo_sel field of the RFLOW_RFC register. See
* the UDMAP section of the TRM for more information on this setting.
*
* @rx_fdq0_sz0_qnum:
* UDMAP receive flow free descriptor queue 0 configuration to be programmed
* into the rx_fdq0_sz0_qnum field of the flow's RFLOW_RFD register. See the
* UDMAP section of the TRM for more information on this setting. The specified
* free queue must be valid within the Navigator Subsystem and must be owned
* by the host, or a subordinate of the host, requesting allocation and
* configuration of the receive flow.
*
* @rx_fdq1_qnum:
* UDMAP receive flow free descriptor queue 1 configuration to be programmed
* into the rx_fdq1_qnum field of the flow's RFLOW_RFD register. See the
* UDMAP section of the TRM for more information on this setting. The specified
* free queue must be valid within the Navigator Subsystem and must be owned
* by the host, or a subordinate of the host, requesting allocation and
* configuration of the receive flow.
*
* @rx_fdq2_qnum:
* UDMAP receive flow free descriptor queue 2 configuration to be programmed
* into the rx_fdq2_qnum field of the flow's RFLOW_RFE register. See the
* UDMAP section of the TRM for more information on this setting. The specified
* free queue must be valid within the Navigator Subsystem and must be owned
* by the host, or a subordinate of the host, requesting allocation and
* configuration of the receive flow.
*
* @rx_fdq3_qnum:
* UDMAP receive flow free descriptor queue 3 configuration to be programmed
* into the rx_fdq3_qnum field of the flow's RFLOW_RFE register. See the
* UDMAP section of the TRM for more information on this setting. The specified
* free queue must be valid within the Navigator Subsystem and must be owned
* by the host, or a subordinate of the host, requesting allocation and
* configuration of the receive flow.
*
* @rx_ps_location:
* UDMAP receive flow PS words location configuration to be programmed into the
* rx_ps_location field of the flow's RFLOW_RFA register.
*/
struct ti_sci_msg_rm_udmap_flow_cfg_req {
struct ti_sci_msg_hdr hdr;
u32 valid_params;
u16 nav_id;
u16 flow_index;
u8 rx_einfo_present;
u8 rx_psinfo_present;
u8 rx_error_handling;
u8 rx_desc_type;
u16 rx_sop_offset;
u16 rx_dest_qnum;
u8 rx_src_tag_hi;
u8 rx_src_tag_lo;
u8 rx_dest_tag_hi;
u8 rx_dest_tag_lo;
u8 rx_src_tag_hi_sel;
u8 rx_src_tag_lo_sel;
u8 rx_dest_tag_hi_sel;
u8 rx_dest_tag_lo_sel;
u16 rx_fdq0_sz0_qnum;
u16 rx_fdq1_qnum;
u16 rx_fdq2_qnum;
u16 rx_fdq3_qnum;
u8 rx_ps_location;
} __packed;
/**
* struct ti_sci_msg_req_proc_request - Request a processor
* @hdr: Generic Header
* @processor_id: ID of processor being requested
*
* Request type is TI_SCI_MSG_PROC_REQUEST, response is a generic ACK/NACK
* message.
*/
struct ti_sci_msg_req_proc_request {
struct ti_sci_msg_hdr hdr;
u8 processor_id;
} __packed;
/**
* struct ti_sci_msg_req_proc_release - Release a processor
* @hdr: Generic Header
* @processor_id: ID of processor being released
*
* Request type is TI_SCI_MSG_PROC_RELEASE, response is a generic ACK/NACK
* message.
*/
struct ti_sci_msg_req_proc_release {
struct ti_sci_msg_hdr hdr;
u8 processor_id;
} __packed;
/**
* struct ti_sci_msg_req_proc_handover - Handover a processor to a host
* @hdr: Generic Header
* @processor_id: ID of processor being handed over
* @host_id: Host ID the control needs to be transferred to
*
* Request type is TI_SCI_MSG_PROC_HANDOVER, response is a generic ACK/NACK
* message.
*/
struct ti_sci_msg_req_proc_handover {
struct ti_sci_msg_hdr hdr;
u8 processor_id;
u8 host_id;
} __packed;
/* Boot Vector masks */
#define TI_SCI_ADDR_LOW_MASK GENMASK_ULL(31, 0)
#define TI_SCI_ADDR_HIGH_MASK GENMASK_ULL(63, 32)
#define TI_SCI_ADDR_HIGH_SHIFT 32
/**
* struct ti_sci_msg_req_set_config - Set Processor boot configuration
* @hdr: Generic Header
* @processor_id: ID of processor being configured
* @bootvector_low: Lower 32 bit address (Little Endian) of boot vector
* @bootvector_high: Higher 32 bit address (Little Endian) of boot vector
* @config_flags_set: Optional Processor specific Config Flags to set.
* Setting a bit here implies the corresponding mode
* will be set
* @config_flags_clear: Optional Processor specific Config Flags to clear.
* Setting a bit here implies the corresponding mode
* will be cleared
*
* Request type is TI_SCI_MSG_PROC_HANDOVER, response is a generic ACK/NACK
* message.
*/
struct ti_sci_msg_req_set_config {
struct ti_sci_msg_hdr hdr;
u8 processor_id;
u32 bootvector_low;
u32 bootvector_high;
u32 config_flags_set;
u32 config_flags_clear;
} __packed;
/**
* struct ti_sci_msg_req_set_ctrl - Set Processor boot control flags
* @hdr: Generic Header
* @processor_id: ID of processor being configured
* @control_flags_set: Optional Processor specific Control Flags to set.
* Setting a bit here implies the corresponding mode
* will be set
* @control_flags_clear:Optional Processor specific Control Flags to clear.
* Setting a bit here implies the corresponding mode
* will be cleared
*
* Request type is TI_SCI_MSG_SET_CTRL, response is a generic ACK/NACK
* message.
*/
struct ti_sci_msg_req_set_ctrl {
struct ti_sci_msg_hdr hdr;
u8 processor_id;
u32 control_flags_set;
u32 control_flags_clear;
} __packed;
/**
* struct ti_sci_msg_req_get_status - Processor boot status request
* @hdr: Generic Header
* @processor_id: ID of processor whose status is being requested
*
* Request type is TI_SCI_MSG_GET_STATUS, response is an appropriate
* message, or NACK in case of inability to satisfy request.
*/
struct ti_sci_msg_req_get_status {
struct ti_sci_msg_hdr hdr;
u8 processor_id;
} __packed;
/**
* struct ti_sci_msg_resp_get_status - Processor boot status response
* @hdr: Generic Header
* @processor_id: ID of processor whose status is returned
* @bootvector_low: Lower 32 bit address (Little Endian) of boot vector
* @bootvector_high: Higher 32 bit address (Little Endian) of boot vector
* @config_flags: Optional Processor specific Config Flags set currently
* @control_flags: Optional Processor specific Control Flags set currently
* @status_flags: Optional Processor specific Status Flags set currently
*
* Response structure to a TI_SCI_MSG_GET_STATUS request.
*/
struct ti_sci_msg_resp_get_status {
struct ti_sci_msg_hdr hdr;
u8 processor_id;
u32 bootvector_low;
u32 bootvector_high;
u32 config_flags;
u32 control_flags;
u32 status_flags;
} __packed;
#endif /* __TI_SCI_H */