1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 | /* SPDX-License-Identifier: GPL-2.0 */ #ifndef __LIS3LV02D_H_ #define __LIS3LV02D_H_ /** * struct lis3lv02d_platform_data - lis3 chip family platform data * @click_flags: Click detection unit configuration * @click_thresh_x: Click detection unit x axis threshold * @click_thresh_y: Click detection unit y axis threshold * @click_thresh_z: Click detection unit z axis threshold * @click_time_limit: Click detection unit time parameter * @click_latency: Click detection unit latency parameter * @click_window: Click detection unit window parameter * @irq_cfg: On chip irq source and type configuration (click / * data available / wake up, open drain, polarity) * @irq_flags1: Additional irq triggering flags for irq channel 0 * @irq_flags2: Additional irq triggering flags for irq channel 1 * @duration1: Wake up unit 1 duration parameter * @duration2: Wake up unit 2 duration parameter * @wakeup_flags: Wake up unit 1 flags * @wakeup_thresh: Wake up unit 1 threshold value * @wakeup_flags2: Wake up unit 2 flags * @wakeup_thresh2: Wake up unit 2 threshold value * @hipass_ctrl: High pass filter control (enable / disable, cut off * frequency) * @axis_x: Sensor orientation remapping for x-axis * @axis_y: Sensor orientation remapping for y-axis * @axis_z: Sensor orientation remapping for z-axis * @driver_features: Enable bits for different features. Disabled by default * @default_rate: Default sampling rate. 0 means reset default * @setup_resources: Interrupt line setup call back function * @release_resources: Interrupt line release call back function * @st_min_limits[3]: Selftest acceptance minimum values * @st_max_limits[3]: Selftest acceptance maximum values * @irq2: Irq line 2 number * * Platform data is used to setup the sensor chip. Meaning of the different * chip features can be found from the data sheet. It is publicly available * at www.st.com web pages. Currently the platform data is used * only for the 8 bit device. The 8 bit device has two wake up / free fall * detection units and click detection unit. There are plenty of ways to * configure the chip which makes is quite hard to explain deeper meaning of * the fields here. Behaviour of the detection blocks varies heavily depending * on the configuration. For example, interrupt detection block can use high * pass filtered data which makes it react to the changes in the acceleration. * Irq_flags can be used to enable interrupt detection on the both edges. * With proper chip configuration this produces interrupt when some trigger * starts and when it goes away. */ struct lis3lv02d_platform_data { /* please note: the 'click' feature is only supported for * LIS[32]02DL variants of the chip and will be ignored for * others */ #define LIS3_CLICK_SINGLE_X (1 << 0) #define LIS3_CLICK_DOUBLE_X (1 << 1) #define LIS3_CLICK_SINGLE_Y (1 << 2) #define LIS3_CLICK_DOUBLE_Y (1 << 3) #define LIS3_CLICK_SINGLE_Z (1 << 4) #define LIS3_CLICK_DOUBLE_Z (1 << 5) unsigned char click_flags; unsigned char click_thresh_x; unsigned char click_thresh_y; unsigned char click_thresh_z; unsigned char click_time_limit; unsigned char click_latency; unsigned char click_window; #define LIS3_IRQ1_DISABLE (0 << 0) #define LIS3_IRQ1_FF_WU_1 (1 << 0) #define LIS3_IRQ1_FF_WU_2 (2 << 0) #define LIS3_IRQ1_FF_WU_12 (3 << 0) #define LIS3_IRQ1_DATA_READY (4 << 0) #define LIS3_IRQ1_CLICK (7 << 0) #define LIS3_IRQ1_MASK (7 << 0) #define LIS3_IRQ2_DISABLE (0 << 3) #define LIS3_IRQ2_FF_WU_1 (1 << 3) #define LIS3_IRQ2_FF_WU_2 (2 << 3) #define LIS3_IRQ2_FF_WU_12 (3 << 3) #define LIS3_IRQ2_DATA_READY (4 << 3) #define LIS3_IRQ2_CLICK (7 << 3) #define LIS3_IRQ2_MASK (7 << 3) #define LIS3_IRQ_OPEN_DRAIN (1 << 6) #define LIS3_IRQ_ACTIVE_LOW (1 << 7) unsigned char irq_cfg; unsigned char irq_flags1; /* Additional irq edge / level flags */ unsigned char irq_flags2; /* Additional irq edge / level flags */ unsigned char duration1; unsigned char duration2; #define LIS3_WAKEUP_X_LO (1 << 0) #define LIS3_WAKEUP_X_HI (1 << 1) #define LIS3_WAKEUP_Y_LO (1 << 2) #define LIS3_WAKEUP_Y_HI (1 << 3) #define LIS3_WAKEUP_Z_LO (1 << 4) #define LIS3_WAKEUP_Z_HI (1 << 5) unsigned char wakeup_flags; unsigned char wakeup_thresh; unsigned char wakeup_flags2; unsigned char wakeup_thresh2; #define LIS3_HIPASS_CUTFF_8HZ 0 #define LIS3_HIPASS_CUTFF_4HZ 1 #define LIS3_HIPASS_CUTFF_2HZ 2 #define LIS3_HIPASS_CUTFF_1HZ 3 #define LIS3_HIPASS1_DISABLE (1 << 2) #define LIS3_HIPASS2_DISABLE (1 << 3) unsigned char hipass_ctrl; #define LIS3_NO_MAP 0 #define LIS3_DEV_X 1 #define LIS3_DEV_Y 2 #define LIS3_DEV_Z 3 #define LIS3_INV_DEV_X -1 #define LIS3_INV_DEV_Y -2 #define LIS3_INV_DEV_Z -3 s8 axis_x; s8 axis_y; s8 axis_z; #define LIS3_USE_BLOCK_READ 0x02 u16 driver_features; int default_rate; int (*setup_resources)(void); int (*release_resources)(void); /* Limits for selftest are specified in chip data sheet */ s16 st_min_limits[3]; /* min pass limit x, y, z */ s16 st_max_limits[3]; /* max pass limit x, y, z */ int irq2; }; #endif /* __LIS3LV02D_H_ */ |