/*
* pata_opti.c - ATI PATA for new ATA layer
* (C) 2005 Red Hat Inc
*
* Based on
* linux/drivers/ide/pci/opti621.c Version 0.7 Sept 10, 2002
*
* Copyright (C) 1996-1998 Linus Torvalds & authors (see below)
*
* Authors:
* Jaromir Koutek <miri@punknet.cz>,
* Jan Harkes <jaharkes@cwi.nl>,
* Mark Lord <mlord@pobox.com>
* Some parts of code are from ali14xx.c and from rz1000.c.
*
* Also consulted the FreeBSD prototype driver by Kevin Day to try
* and resolve some confusions. Further documentation can be found in
* Ralf Brown's interrupt list
*
* If you have other variants of the Opti range (Viper/Vendetta) please
* try this driver with those PCI idents and report back. For the later
* chips see the pata_optidma driver
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_opti"
#define DRV_VERSION "0.2.9"
enum {
READ_REG = 0, /* index of Read cycle timing register */
WRITE_REG = 1, /* index of Write cycle timing register */
CNTRL_REG = 3, /* index of Control register */
STRAP_REG = 5, /* index of Strap register */
MISC_REG = 6 /* index of Miscellaneous register */
};
/**
* opti_pre_reset - probe begin
* @link: ATA link
* @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
static int opti_pre_reset(struct ata_link *link, unsigned long deadline)
{
struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const struct pci_bits opti_enable_bits[] = {
{ 0x45, 1, 0x80, 0x00 },
{ 0x40, 1, 0x08, 0x00 }
};
if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no]))
return -ENOENT;
return ata_sff_prereset(link, deadline);
}
/**
* opti_write_reg - control register setup
* @ap: ATA port
* @value: value
* @reg: control register number
*
* The Opti uses magic 'trapdoor' register accesses to do configuration
* rather than using PCI space as other controllers do. The double inw
* on the error register activates configuration mode. We can then write
* the control register
*/
static void opti_write_reg(struct ata_port *ap, u8 val, int reg)
{
void __iomem *regio = ap->ioaddr.cmd_addr;
/* These 3 unlock the control register access */
ioread16(regio + 1);
ioread16(regio + 1);
iowrite8(3, regio + 2);
/* Do the I/O */
iowrite8(val, regio + reg);
/* Relock */
iowrite8(0x83, regio + 2);
}
/**
* opti_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the PIO mode setup. Timing numbers are taken from
* the FreeBSD driver then pre computed to keep the code clean. There
* are two tables depending on the hardware clock speed.
*/
static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
struct ata_device *pair = ata_dev_pair(adev);
int clock;
int pio = adev->pio_mode - XFER_PIO_0;
void __iomem *regio = ap->ioaddr.cmd_addr;
u8 addr;
/* Address table precomputed with prefetch off and a DCLK of 2 */
static const u8 addr_timing[2][5] = {
{ 0x30, 0x20, 0x20, 0x10, 0x10 },
{ 0x20, 0x20, 0x10, 0x10, 0x10 }
};
static const u8 data_rec_timing[2][5] = {
{ 0x6B, 0x56, 0x42, 0x32, 0x31 },
{ 0x58, 0x44, 0x32, 0x22, 0x21 }
};
iowrite8(0xff, regio + 5);
clock = ioread16(regio + 5) & 1;
/*
* As with many controllers the address setup time is shared
* and must suit both devices if present.
*/
addr = addr_timing[clock][pio];
if (pair) {
/* Hardware constraint */
u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0];
if (pair_addr > addr)
addr = pair_addr;
}
/* Commence primary programming sequence */
opti_write_reg(ap, adev->devno, MISC_REG);
opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG);
opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG);
opti_write_reg(ap, addr, MISC_REG);
/* Programming sequence complete, override strapping */
opti_write_reg(ap, 0x85, CNTRL_REG);
}
static struct scsi_host_template opti_sht = {
ATA_PIO_SHT(DRV_NAME),
};
static struct ata_port_operations opti_port_ops = {
.inherits = &ata_sff_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = opti_set_piomode,
.prereset = opti_pre_reset,
};
static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.port_ops = &opti_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
ata_print_version_once(&dev->dev, DRV_VERSION);
return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL, 0);
}
static const struct pci_device_id opti[] = {
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
{ },
};
static struct pci_driver opti_pci_driver = {
.name = DRV_NAME,
.id_table = opti,
.probe = opti_init_one,
.remove = ata_pci_remove_one,
#ifdef [31mCONFIG_PM_SLEEP[0m
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
module_pci_driver(opti_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Opti 621/621X");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, opti);
MODULE_VERSION(DRV_VERSION);