#
# GPIO infrastructure and drivers
#
config [31mCONFIG_ARCH_HAVE_CUSTOM_GPIO_H[0m
bool
help
Selecting this config option from the architecture Kconfig allows
the architecture to provide a custom asm/gpio.h implementation
overriding the default implementations. New uses of this are
strongly discouraged.
menuconfig [31mCONFIG_GPIOLIB[0m
bool "GPIO Support"
select [31mCONFIG_ANON_INODES[0m
help
This enables GPIO support through the generic GPIO library.
You only need to enable this, if you also want to enable
one or more of the GPIO drivers below.
If unsure, say N.
if [31mCONFIG_GPIOLIB[0m
config [31mCONFIG_OF_GPIO[0m
def_bool y
depends on [31mCONFIG_OF[0m
depends on [31mCONFIG_HAS_IOMEM[0m
config [31mCONFIG_GPIO_ACPI[0m
def_bool y
depends on [31mCONFIG_ACPI[0m
config [31mCONFIG_GPIOLIB_IRQCHIP[0m
select [31mCONFIG_IRQ_DOMAIN[0m
bool
config [31mCONFIG_DEBUG_GPIO[0m
bool "Debug GPIO calls"
depends on [31mCONFIG_DEBUG_KERNEL[0m
help
Say Y here to add some extra checks and diagnostics to GPIO calls.
These checks help ensure that GPIOs have been properly initialized
before they are used, and that sleeping calls are not made from
non-sleeping contexts. They can make bitbanged serial protocols
slower. The diagnostics help catch the type of setup errors
that are most common when setting up new platforms or boards.
config [31mCONFIG_GPIO_SYSFS[0m
bool "/sys/class/gpio/... (sysfs interface)"
depends on [31mCONFIG_SYSFS[0m
help
Say Y here to add a sysfs interface for GPIOs.
This is mostly useful to work around omissions in a system's
kernel support. Those are common in custom and semicustom
hardware assembled using standard kernels with a minimum of
custom patches. In those cases, userspace code may import
a given GPIO from the kernel, if no kernel driver requested it.
Kernel drivers may also request that a particular GPIO be
exported to userspace; this can be useful when debugging.
config [31mCONFIG_GPIO_GENERIC[0m
depends on [31mCONFIG_HAS_IOMEM[0m # Only for IOMEM drivers
tristate
# put drivers in the right section, in alphabetical order
# This symbol is selected by both [31mCONFIG_I2C[0m and [31mCONFIG_SPI[0m expanders
config [31mCONFIG_GPIO_MAX730X[0m
tristate
menu "Memory mapped GPIO drivers"
depends on [31mCONFIG_HAS_IOMEM[0m
config [31mCONFIG_GPIO_74XX_MMIO[0m
tristate "GPIO driver for 74xx-ICs with MMIO access"
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
Say yes here to support GPIO functionality for 74xx-compatible ICs
with MMIO access. Compatible models include:
1 bit: 741G125 (Input), 741G74 (Output)
2 bits: 742G125 (Input), 7474 (Output)
4 bits: 74125 (Input), 74175 (Output)
6 bits: 74365 (Input), 74174 (Output)
8 bits: 74244 (Input), 74273 (Output)
16 bits: 741624 (Input), 7416374 (Output)
config [31mCONFIG_GPIO_ALTERA[0m
tristate "Altera GPIO"
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say Y or [31mCONFIG_M[0m here to build support for the Altera PIO device.
If driver is built as a module it will be called gpio-altera.
config [31mCONFIG_GPIO_AMDPT[0m
tristate "AMD Promontory GPIO support"
depends on [31mCONFIG_ACPI[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
driver for GPIO functionality on Promontory IOHub
Require [31mCONFIG_ACPI[0m ASL code to enumerate as a platform device.
config [31mCONFIG_GPIO_ASPEED[0m
tristate "Aspeed GPIO support"
depends on ([31mCONFIG_ARCH_ASPEED[0m || [31mCONFIG_COMPILE_TEST[0m) && [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say Y here to support Aspeed AST2400 and AST2500 GPIO controllers.
config [31mCONFIG_GPIO_ATH79[0m
tristate "Atheros AR71XX/AR724X/AR913X GPIO support"
default y if [31mCONFIG_ATH79[0m
depends on [31mCONFIG_ATH79[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Select this option to enable GPIO driver for
Atheros AR71XX/AR724X/AR913X SoC devices.
config [31mCONFIG_GPIO_AXP209[0m
tristate "X-Powers AXP209 PMIC GPIO Support"
depends on [31mCONFIG_MFD_AXP20X[0m
help
Say yes to enable GPIO support for the AXP209 PMIC
config [31mCONFIG_GPIO_BCM_KONA[0m
bool "Broadcom Kona GPIO"
depends on [31mCONFIG_OF_GPIO[0m && ([31mCONFIG_ARCH_BCM_MOBILE[0m || [31mCONFIG_COMPILE_TEST[0m)
help
Turn on GPIO support for Broadcom "Kona" chips.
config [31mCONFIG_GPIO_BRCMSTB[0m
tristate "BRCMSTB GPIO support"
default y if ([31mCONFIG_ARCH_BRCMSTB[0m || [31mCONFIG_BMIPS_GENERIC[0m)
depends on [31mCONFIG_OF_GPIO[0m && ([31mCONFIG_ARCH_BRCMSTB[0m || [31mCONFIG_BMIPS_GENERIC[0m || [31mCONFIG_COMPILE_TEST[0m)
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.
config [31mCONFIG_GPIO_CLPS711X[0m
tristate "CLPS711X GPIO support"
depends on [31mCONFIG_ARCH_CLPS711X[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
Say yes here to support GPIO on CLPS711X SoCs.
config [31mCONFIG_GPIO_DAVINCI[0m
bool "TI Davinci/Keystone GPIO support"
default y if [31mCONFIG_ARCH_DAVINCI[0m
depends on [31mCONFIG_ARM[0m && ([31mCONFIG_ARCH_DAVINCI[0m || [31mCONFIG_ARCH_KEYSTONE[0m)
help
Say yes here to enable GPIO support for TI Davinci/Keystone SoCs.
config [31mCONFIG_GPIO_DWAPB[0m
tristate "Synopsys DesignWare APB GPIO driver"
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
help
Say Y or [31mCONFIG_M[0m here to build support for the Synopsys DesignWare APB
GPIO block.
config [31mCONFIG_GPIO_EM[0m
tristate "Emma Mobile GPIO"
depends on ([31mCONFIG_ARCH_EMEV2[0m || [31mCONFIG_COMPILE_TEST[0m) && [31mCONFIG_OF_GPIO[0m
help
Say yes here to support GPIO on Renesas Emma Mobile SoCs.
config [31mCONFIG_GPIO_EP93XX[0m
def_bool y
depends on [31mCONFIG_ARCH_EP93XX[0m
select [31mCONFIG_GPIO_GENERIC[0m
config [31mCONFIG_GPIO_ETRAXFS[0m
bool "Axis ETRAX FS General I/O"
depends on [31mCONFIG_CRIS[0m || [31mCONFIG_COMPILE_TEST[0m
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to support the GPIO controller on Axis ETRAX FS SoCs.
config [31mCONFIG_GPIO_GE_FPGA[0m
bool "GE FPGA based GPIO"
depends on [31mCONFIG_GE_FPGA[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
Support for common GPIO functionality provided on some GE Single Board
Computers.
This driver provides basic support (configure as input or output, read
and write pin state) for GPIO implemented in a number of GE single
board computers.
config [31mCONFIG_GPIO_GENERIC_PLATFORM[0m
tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
select [31mCONFIG_GPIO_GENERIC[0m
help
Say yes here to support basic platform_device memory-mapped GPIO controllers.
config [31mCONFIG_GPIO_GRGPIO[0m
tristate "Aeroflex Gaisler GRGPIO support"
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_IRQ_DOMAIN[0m
help
Select this to support Aeroflex Gaisler GRGPIO cores from the GRLIB
VHDL IP core library.
config [31mCONFIG_GPIO_ICH[0m
tristate "Intel ICH GPIO"
depends on [31mCONFIG_PCI[0m && [31mCONFIG_X86[0m
select [31mCONFIG_MFD_CORE[0m
select [31mCONFIG_LPC_ICH[0m
help
Say yes here to support the GPIO functionality of a number of Intel
ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8
ICH9, ICH10, Series 5/3400 (eg Ibex Peak), Series 6/C200 (eg
Cougar Point), NM10 (Tiger Point), and 3100 (Whitmore Lake).
If unsure, say N.
config [31mCONFIG_GPIO_IOP[0m
tristate "Intel IOP GPIO"
depends on [31mCONFIG_ARCH_IOP32X[0m || [31mCONFIG_ARCH_IOP33X[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
Say yes here to support the GPIO functionality of a number of Intel
IOP32X or IOP33X.
If unsure, say N.
config [31mCONFIG_GPIO_LOONGSON[0m
bool "Loongson-2/3 GPIO support"
depends on [31mCONFIG_CPU_LOONGSON2[0m || [31mCONFIG_CPU_LOONGSON3[0m
help
driver for GPIO functionality on Loongson-2F/3A/3B processors.
config [31mCONFIG_GPIO_LPC18XX[0m
tristate "NXP LPC18XX/43XX GPIO support"
default y if [31mCONFIG_ARCH_LPC18XX[0m
depends on [31mCONFIG_OF_GPIO[0m && ([31mCONFIG_ARCH_LPC18XX[0m || [31mCONFIG_COMPILE_TEST[0m)
help
Select this option to enable GPIO driver for
NXP LPC18XX/43XX devices.
config [31mCONFIG_GPIO_LYNXPOINT[0m
tristate "Intel Lynxpoint GPIO support"
depends on [31mCONFIG_ACPI[0m && [31mCONFIG_X86[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
driver for GPIO functionality on Intel Lynxpoint PCH chipset
Requires [31mCONFIG_ACPI[0m device enumeration code to set up a platform device.
config [31mCONFIG_GPIO_MB86S7X[0m
bool "GPIO support for Fujitsu MB86S7x Platforms"
depends on ARCH_MB86S7X || [31mCONFIG_COMPILE_TEST[0m
help
Say yes here to support the GPIO controller in Fujitsu MB86S70 SoCs.
config [31mCONFIG_GPIO_MENZ127[0m
tristate "MEN 16Z127 GPIO support"
depends on [31mCONFIG_MCB[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
Say yes here to support the MEN 16Z127 GPIO Controller
config [31mCONFIG_GPIO_MM_LANTIQ[0m
bool "Lantiq Memory mapped GPIOs"
depends on [31mCONFIG_LANTIQ[0m && [31mCONFIG_SOC_XWAY[0m
help
This enables support for memory mapped GPIOs on the External Bus Unit
(EBU) found on Lantiq SoCs. The gpios are output only as they are
created by attaching a 16bit latch to the bus.
config [31mCONFIG_GPIO_MOCKUP[0m
tristate "GPIO Testing Driver"
depends on [31mCONFIG_GPIOLIB[0m && [31mCONFIG_SYSFS[0m
select [31mCONFIG_GPIO_SYSFS[0m
help
This enables GPIO Testing driver, which provides a way to test GPIO
subsystem through sysfs(or char device) and debugfs. [31mCONFIG_GPIO_SYSFS[0m
must be selected for this test.
User could use it through the script in
tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
it.
config [31mCONFIG_GPIO_MOXART[0m
bool "MOXART GPIO support"
depends on [31mCONFIG_ARCH_MOXART[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
Select this option to enable GPIO driver for
MOXA ART SoC devices.
config [31mCONFIG_GPIO_MPC5200[0m
def_bool y
depends on [31mCONFIG_PPC_MPC52xx[0m
config [31mCONFIG_GPIO_MPC8XXX[0m
bool "MPC512x/MPC8xxx/QorIQ GPIO support"
depends on [31mCONFIG_PPC_MPC512x[0m || [31mCONFIG_PPC_MPC831x[0m || [31mCONFIG_PPC_MPC834x[0m || [31mCONFIG_PPC_MPC837x[0m || \
[31mCONFIG_FSL_SOC_BOOKE[0m || [31mCONFIG_PPC_86xx[0m || [31mCONFIG_ARCH_LAYERSCAPE[0m || [31mCONFIG_ARM[0m || \
[31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_IRQ_DOMAIN[0m
help
Say Y here if you're going to use hardware that connects to the
MPC512x/831x/834x/837x/8572/8610/QorIQ GPIOs.
config [31mCONFIG_GPIO_MVEBU[0m
def_bool y
depends on [31mCONFIG_PLAT_ORION[0m
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
config [31mCONFIG_GPIO_MXC[0m
def_bool y
depends on [31mCONFIG_ARCH_MXC[0m
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
config [31mCONFIG_GPIO_MXS[0m
def_bool y
depends on [31mCONFIG_ARCH_MXS[0m
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
config [31mCONFIG_GPIO_OCTEON[0m
tristate "Cavium OCTEON GPIO"
depends on [31mCONFIG_GPIOLIB[0m && [31mCONFIG_CAVIUM_OCTEON_SOC[0m
default y
help
Say yes here to support the on-chip GPIO lines on the OCTEON
family of SOCs.
config [31mCONFIG_GPIO_OMAP[0m
tristate "TI OMAP GPIO support" if [31mCONFIG_ARCH_OMAP2PLUS[0m || [31mCONFIG_COMPILE_TEST[0m
default y if [31mCONFIG_ARCH_OMAP[0m
depends on [31mCONFIG_ARM[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to enable GPIO support for TI OMAP SoCs.
config [31mCONFIG_GPIO_PL061[0m
bool "PrimeCell PL061 GPIO support"
depends on [31mCONFIG_ARM_AMBA[0m
select [31mCONFIG_IRQ_DOMAIN[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to support the PrimeCell PL061 GPIO device
config [31mCONFIG_GPIO_PXA[0m
bool "PXA GPIO support"
depends on [31mCONFIG_ARCH_PXA[0m || [31mCONFIG_ARCH_MMP[0m
help
Say yes here to support the PXA GPIO device
config [31mCONFIG_GPIO_RCAR[0m
tristate "Renesas R-Car GPIO"
depends on [31mCONFIG_ARCH_RENESAS[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to support GPIO on Renesas R-Car SoCs.
config [31mCONFIG_GPIO_SPEAR_SPICS[0m
bool "ST SPEAr13xx SPI Chip Select as GPIO support"
depends on [31mCONFIG_PLAT_SPEAR[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
help
Say yes here to support ST SPEAr [31mCONFIG_SPI[0m Chip Select as GPIO device
config [31mCONFIG_GPIO_STA2X11[0m
bool "STA2x11/ConneXt GPIO support"
depends on [31mCONFIG_MFD_STA2X11[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
help
Say yes here to support the STA2x11/ConneXt GPIO device.
The GPIO module has 128 GPIO pins with alternate functions.
config [31mCONFIG_GPIO_STP_XWAY[0m
bool "XWAY STP GPIOs"
depends on [31mCONFIG_SOC_XWAY[0m
help
This enables support for the Serial To Parallel ([31mCONFIG_STP[0m) unit found on
XWAY SoC. The [31mCONFIG_STP[0m allows the SoC to drive a shift registers cascade,
that can be up to 24 bit. This peripheral is aimed at driving leds.
Some of the gpios/leds can be auto updated by the soc with dsl and
phy status.
config [31mCONFIG_GPIO_SYSCON[0m
tristate "GPIO based on SYSCON"
depends on [31mCONFIG_MFD_SYSCON[0m && [31mCONFIG_OF[0m
help
Say yes here to support GPIO functionality though SYSCON driver.
config [31mCONFIG_GPIO_TB10X[0m
bool
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
select [31mCONFIG_OF_GPIO[0m
config [31mCONFIG_GPIO_TEGRA[0m
bool "NVIDIA Tegra GPIO support"
default [31mCONFIG_ARCH_TEGRA[0m
depends on [31mCONFIG_ARCH_TEGRA[0m || [31mCONFIG_COMPILE_TEST[0m
depends on [31mCONFIG_OF_GPIO[0m
help
Say yes here to support GPIO pins on NVIDIA Tegra SoCs.
config [31mCONFIG_GPIO_TS4800[0m
tristate "TS-4800 DIO blocks and compatibles"
depends on [31mCONFIG_OF_GPIO[0m
depends on [31mCONFIG_SOC_IMX51[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
This driver support TS-4800 [31mCONFIG_FPGA[0m GPIO controllers.
config [31mCONFIG_GPIO_TZ1090[0m
bool "Toumaz Xenif TZ1090 GPIO support"
depends on [31mCONFIG_SOC_TZ1090[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
default y
help
Say yes here to support Toumaz Xenif TZ1090 GPIOs.
config [31mCONFIG_GPIO_TZ1090_PDC[0m
bool "Toumaz Xenif TZ1090 PDC GPIO support"
depends on [31mCONFIG_SOC_TZ1090[0m
default y
help
Say yes here to support Toumaz Xenif TZ1090 PDC GPIOs.
config [31mCONFIG_GPIO_VF610[0m
def_bool y
depends on [31mCONFIG_ARCH_MXC[0m && [31mCONFIG_SOC_VF610[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to support Vybrid vf610 GPIOs.
config [31mCONFIG_GPIO_VR41XX[0m
tristate "NEC VR4100 series General-purpose I/O Uint support"
depends on [31mCONFIG_CPU_VR41XX[0m
help
Say yes here to support the NEC VR4100 series General-purpose I/O Uint
config [31mCONFIG_GPIO_VX855[0m
tristate "VIA VX855/VX875 GPIO"
depends on ([31mCONFIG_X86[0m || [31mCONFIG_COMPILE_TEST[0m) && [31mCONFIG_PCI[0m
select [31mCONFIG_MFD_CORE[0m
select [31mCONFIG_MFD_VX855[0m
help
Support access to the VX855/VX875 GPIO lines through the gpio library.
This driver provides common support for accessing the device,
additional drivers must be enabled in order to use the
functionality of the device.
config [31mCONFIG_GPIO_XGENE[0m
bool "APM X-Gene GPIO controller support"
depends on [31mCONFIG_ARM64[0m && [31mCONFIG_OF_GPIO[0m
help
This driver is to support the GPIO block within the [31mCONFIG_APM[0m X-Gene SoC
platform's generic flash controller. The GPIO pins are muxed with
the generic flash controller's address and data pins. Say yes
here to enable the GFC GPIO functionality.
config [31mCONFIG_GPIO_XGENE_SB[0m
tristate "APM X-Gene GPIO standby controller support"
depends on [31mCONFIG_ARCH_XGENE[0m && [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
This driver supports the GPIO block within the [31mCONFIG_APM[0m X-Gene
Standby Domain. Say yes here to enable the GPIO functionality.
config [31mCONFIG_GPIO_XILINX[0m
tristate "Xilinx GPIO support"
depends on [31mCONFIG_OF_GPIO[0m
help
Say yes here to support the Xilinx [31mCONFIG_FPGA[0m GPIO device
config [31mCONFIG_GPIO_XLP[0m
tristate "Netlogic XLP GPIO support"
depends on [31mCONFIG_OF_GPIO[0m && ([31mCONFIG_CPU_XLP[0m || [31mCONFIG_ARCH_VULCAN[0m || [31mCONFIG_COMPILE_TEST[0m)
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
This driver provides support for GPIO interface on Netlogic XLP MIPS64
SoCs. Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX,
XLP9XX and XLP5XX.
If unsure, say N.
config [31mCONFIG_GPIO_XTENSA[0m
bool "Xtensa GPIO32 support"
depends on [31mCONFIG_XTENSA[0m
depends on [31mCONFIG_HAVE_XTENSA_GPIO32[0m
depends on ![31mCONFIG_SMP[0m
help
Say yes here to support the Xtensa internal GPIO32 IMPWIRE (input)
and EXPSTATE (output) ports
config [31mCONFIG_GPIO_ZEVIO[0m
bool "LSI ZEVIO SoC memory mapped GPIOs"
depends on [31mCONFIG_ARM[0m && [31mCONFIG_OF_GPIO[0m
help
Say yes here to support the GPIO controller in LSI ZEVIO SoCs.
config [31mCONFIG_GPIO_ZYNQ[0m
tristate "Xilinx Zynq GPIO support"
depends on [31mCONFIG_ARCH_ZYNQ[0m || [31mCONFIG_ARCH_ZYNQMP[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to support Xilinx Zynq GPIO controller.
config [31mCONFIG_GPIO_ZX[0m
bool "ZTE ZX GPIO support"
depends on [31mCONFIG_ARCH_ZX[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to support the GPIO device on ZTE ZX SoCs.
config [31mCONFIG_GPIO_LOONGSON1[0m
tristate "Loongson1 GPIO support"
depends on [31mCONFIG_MACH_LOONGSON32[0m
select [31mCONFIG_GPIO_GENERIC[0m
help
Say Y or [31mCONFIG_M[0m here to support GPIO on Loongson1 SoCs.
endmenu
menu "Port-mapped I/O GPIO drivers"
depends on [31mCONFIG_X86[0m # Unconditional I/O space access
config [31mCONFIG_GPIO_104_DIO_48E[0m
tristate "ACCES 104-DIO-48E GPIO support"
depends on [31mCONFIG_ISA_BUS_API[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Enables GPIO support for the ACCES 104-[31mCONFIG_DIO[0m-48E series (104-[31mCONFIG_DIO[0m-48E,
104-[31mCONFIG_DIO[0m-24E). The base port addresses for the devices may be
configured via the base module parameter. The interrupt line numbers
for the devices may be configured via the irq module parameter.
config [31mCONFIG_GPIO_104_IDIO_16[0m
tristate "ACCES 104-IDIO-16 GPIO support"
depends on [31mCONFIG_ISA_BUS_API[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Enables GPIO support for the ACCES 104-IDIO-16 family (104-IDIO-16,
104-IDIO-16E, 104-IDO-16, 104-IDIO-8, 104-IDIO-8E, 104-IDO-8). The
base port addresses for the devices may be configured via the base
module parameter. The interrupt line numbers for the devices may be
configured via the irq module parameter.
config [31mCONFIG_GPIO_104_IDI_48[0m
tristate "ACCES 104-IDI-48 GPIO support"
depends on [31mCONFIG_ISA_BUS_API[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Enables GPIO support for the ACCES 104-IDI-48 family (104-IDI-48A,
104-IDI-48AC, 104-IDI-48B, 104-IDI-48BC). The base port addresses for
the devices may be configured via the base module parameter. The
interrupt line numbers for the devices may be configured via the irq
module parameter.
config [31mCONFIG_GPIO_F7188X[0m
tristate "F71869, F71869A, F71882FG, F71889F and F81866 GPIO support"
help
This option enables support for GPIOs found on Fintek Super-I/O
chips F71869, F71869A, F71882FG, F71889F and F81866.
To compile this driver as a module, choose [31mCONFIG_M[0m here: the module will
be called f7188x-gpio.
config [31mCONFIG_GPIO_GPIO_MM[0m
tristate "Diamond Systems GPIO-MM GPIO support"
depends on [31mCONFIG_ISA_BUS_API[0m
help
Enables GPIO support for the Diamond Systems GPIO-MM and GPIO-MM-12.
The Diamond Systems GPIO-MM device features 48 lines of digital I/O
via the emulation of dual 82C55A PPI chips. This driver provides GPIO
support for these 48 channels of digital I/O.
The base port addresses for the devices may be configured via the base
array module parameter.
config [31mCONFIG_GPIO_IT87[0m
tristate "IT87xx GPIO support"
help
Say yes here to support GPIO functionality of IT87xx Super I/O chips.
This driver is tested with ITE IT8728 and IT8732 Super I/O chips, and
supports the IT8761E, IT8620E and IT8628E Super I/O chip as well.
To compile this driver as a module, choose [31mCONFIG_M[0m here: the module will
be called gpio_it87
config [31mCONFIG_GPIO_SCH[0m
tristate "Intel SCH/TunnelCreek/Centerton/Quark X1000 GPIO"
depends on ([31mCONFIG_X86[0m || [31mCONFIG_COMPILE_TEST[0m) && [31mCONFIG_PCI[0m
select [31mCONFIG_MFD_CORE[0m
select [31mCONFIG_LPC_SCH[0m
help
Say yes here to support GPIO interface on Intel Poulsbo SCH,
Intel Tunnel Creek processor, Intel Centerton processor or
Intel Quark X1000 SoC.
The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
powered by the core power rail and are turned off during sleep
modes (S3 and higher). The remaining four GPIOs are powered by
the Intel SCH suspend power supply. These GPIOs remain
active during S3. The suspend powered GPIOs can be used to wake the
system from the Suspend-to-RAM state.
The Intel Tunnel Creek processor has 5 GPIOs powered by the
core power rail and 9 from suspend power supply.
The Intel Centerton processor has a total of 30 GPIO pins.
Twenty-one are powered by the core power rail and 9 from the
suspend power supply.
The Intel Quark X1000 SoC has 2 GPIOs powered by the core
power well and 6 from the suspend power well.
config [31mCONFIG_GPIO_SCH311X[0m
tristate "SMSC SCH311x SuperI/O GPIO"
help
Driver to enable the GPIOs found on SMSC SMSC SCH3112, SCH3114 and
SCH3116 "Super I/O" chipsets.
To compile this driver as a module, choose [31mCONFIG_M[0m here: the module will
be called gpio-sch311x.
config [31mCONFIG_GPIO_TS5500[0m
tristate "TS-5500 DIO blocks and compatibles"
depends on [31mCONFIG_TS5500[0m || [31mCONFIG_COMPILE_TEST[0m
help
This driver supports Digital I/O exposed by pin blocks found on some
Technologic Systems platforms. It includes, but is not limited to, 3
blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
LCD port.
config [31mCONFIG_GPIO_WS16C48[0m
tristate "WinSystems WS16C48 GPIO support"
depends on [31mCONFIG_ISA_BUS_API[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Enables GPIO support for the WinSystems WS16C48. The base port
addresses for the devices may be configured via the base module
parameter. The interrupt line numbers for the devices may be
configured via the irq module parameter.
endmenu
menu "I2C GPIO expanders"
depends on [31mCONFIG_I2C[0m
config [31mCONFIG_GPIO_ADP5588[0m
tristate "ADP5588 I2C GPIO expander"
help
This option enables support for 18 GPIOs found
on Analog Devices ADP5588 GPIO Expanders.
config [31mCONFIG_GPIO_ADP5588_IRQ[0m
bool "Interrupt controller support for ADP5588"
depends on [31mCONFIG_GPIO_ADP5588[0m=y
help
Say yes here to enable the adp5588 to be used as an interrupt
controller. It requires the driver to be built in the kernel.
config [31mCONFIG_GPIO_ADNP[0m
tristate "Avionic Design N-bit GPIO expander"
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
This option enables support for N GPIOs found on Avionic Design
[31mCONFIG_I2C[0m GPIO expanders. The register space will be extended by powers
of two, so the controller will need to accommodate for that. For
example: if a controller provides 48 pins, 6 registers will be
enough to represent all pins, but the driver will assume a
register layout for 64 pins (8 registers).
config [31mCONFIG_GPIO_MAX7300[0m
tristate "Maxim MAX7300 GPIO expander"
select [31mCONFIG_GPIO_MAX730X[0m
help
GPIO driver for Maxim MAX7300 [31mCONFIG_I2C[0m-based GPIO expander.
config [31mCONFIG_GPIO_MAX732X[0m
tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
help
Say yes here to support the MAX7319, MAX7320-7327 series of [31mCONFIG_I2C[0m
Port Expanders. Each IO port on these chips has a fixed role of
Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
Input and Output (designed by 'P'). The combinations are listed
below:
8 bits: max7319 (8I), max7320 (8O), max7321 (8P),
max7322 (4I4O), max7323 (4P4O)
16 bits: max7324 (8I8O), max7325 (8P8O),
max7326 (4I12O), max7327 (4P12O)
Board setup code must specify the model to use, and the start
number for these GPIOs.
config [31mCONFIG_GPIO_MAX732X_IRQ[0m
bool "Interrupt controller support for MAX732x"
depends on [31mCONFIG_GPIO_MAX732X[0m=y
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to enable the max732x to be used as an interrupt
controller. It requires the driver to be built in the kernel.
config [31mCONFIG_GPIO_MC9S08DZ60[0m
bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
depends on [31mCONFIG_I2C[0m=y && [31mCONFIG_MACH_MX35_3DS[0m
help
Select this to enable the MC9S08DZ60 GPIO driver
config [31mCONFIG_GPIO_PCA953X[0m
tristate "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports"
help
Say yes here to provide access to several register-oriented
SMBus I/O expanders, made mostly by NXP or TI. Compatible
models include:
4 bits: pca9536, pca9537
8 bits: max7310, max7315, pca6107, pca9534, pca9538, pca9554,
pca9556, pca9557, pca9574, tca6408, xra1202
16 bits: max7312, max7313, pca9535, pca9539, pca9555, pca9575,
tca6416
24 bits: tca6424
40 bits: pca9505, pca9698
config [31mCONFIG_GPIO_PCA953X_IRQ[0m
bool "Interrupt controller support for PCA953x"
depends on [31mCONFIG_GPIO_PCA953X[0m=y
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say yes here to enable the pca953x to be used as an interrupt
controller. It requires the driver to be built in the kernel.
config [31mCONFIG_GPIO_PCF857X[0m
tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
select [31mCONFIG_IRQ_DOMAIN[0m
help
Say yes here to provide access to most "quasi-bidirectional" [31mCONFIG_I2C[0m
GPIO expanders used for additional digital outputs or inputs.
Most of these parts are from NXP, though TI is a second source for
some of them. Compatible models include:
8 bits: pcf8574, pcf8574a, pca8574, pca8574a,
pca9670, pca9672, pca9674, pca9674a,
max7328, max7329
16 bits: pcf8575, pcf8575c, pca8575,
pca9671, pca9673, pca9675
Your board setup code will need to declare the expanders in
use, and assign numbers to the GPIOs they expose. Those GPIOs
can then be used from drivers and other kernel code, just like
other GPIOs, but only accessible from task contexts.
This driver provides an in-kernel interface to those GPIOs using
platform-neutral GPIO calls.
config [31mCONFIG_GPIO_SX150X[0m
bool "Semtech SX150x I2C GPIO expander (deprecated)"
depends on [31mCONFIG_PINCTRL[0m && [31mCONFIG_I2C[0m=y
select [31mCONFIG_PINCTRL_SX150X[0m
default n
help
Say yes here to provide support for Semtech SX150x-series [31mCONFIG_I2C[0m
GPIO expanders. The GPIO driver was replaced by a Pinctrl version.
config [31mCONFIG_GPIO_TPIC2810[0m
tristate "TPIC2810 8-Bit I2C GPO expander"
help
Say yes here to enable the GPO driver for the TI TPIC2810 chip.
To compile this driver as a module, choose [31mCONFIG_M[0m here: the module will
be called gpio-tpic2810.
config [31mCONFIG_GPIO_TS4900[0m
tristate "Technologic Systems FPGA I2C GPIO"
depends on [31mCONFIG_SOC_IMX6[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_REGMAP_I2C[0m
help
Say yes here to enabled the GPIO driver for Technologic's [31mCONFIG_FPGA[0m core.
Series supported include TS-4100, TS-4900, TS-7970 and TS-7990.
endmenu
menu "MFD GPIO expanders"
config [31mCONFIG_GPIO_ADP5520[0m
tristate "GPIO Support for ADP5520 PMIC"
depends on [31mCONFIG_PMIC_ADP5520[0m
help
This option enables support for on-chip GPIO found
on Analog Devices ADP5520 PMICs.
config [31mCONFIG_GPIO_ALTERA_A10SR[0m
tristate "Altera Arria10 System Resource GPIO"
depends on [31mCONFIG_MFD_ALTERA_A10SR[0m
help
Driver for Arria10 Development Kit GPIO expansion which
includes reads of pushbuttons and DIP switches as well
as writes to LEDs.
config [31mCONFIG_GPIO_ARIZONA[0m
tristate "Wolfson Microelectronics Arizona class devices"
depends on [31mCONFIG_MFD_ARIZONA[0m
help
Support for GPIOs on Wolfson Arizona class devices.
config [31mCONFIG_GPIO_CRYSTAL_COVE[0m
tristate "GPIO support for Crystal Cove PMIC"
depends on ([31mCONFIG_X86[0m || [31mCONFIG_COMPILE_TEST[0m) && [31mCONFIG_INTEL_SOC_PMIC[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Support for GPIO pins on Crystal Cove PMIC.
Say Yes if you have a Intel SoC based tablet with Crystal Cove PMIC
inside.
This driver can also be built as a module. If so, the module will be
called gpio-crystalcove.
config [31mCONFIG_GPIO_CS5535[0m
tristate "AMD CS5535/CS5536 GPIO support"
depends on [31mCONFIG_X86[0m || [31mCONFIG_MIPS[0m || [31mCONFIG_COMPILE_TEST[0m
depends on [31mCONFIG_MFD_CS5535[0m
help
The AMD CS5535 and [31mCONFIG_CS5536[0m southbridges support 28 GPIO pins that
can be used for quite a number of things. The CS5535/6 is found on
AMD Geode and Lemote Yeeloong devices.
If unsure, say N.
config [31mCONFIG_GPIO_DA9052[0m
tristate "Dialog DA9052 GPIO"
depends on [31mCONFIG_PMIC_DA9052[0m
help
Say yes here to enable the GPIO driver for the DA9052 chip.
config [31mCONFIG_GPIO_DA9055[0m
tristate "Dialog Semiconductor DA9055 GPIO"
depends on [31mCONFIG_MFD_DA9055[0m
help
Say yes here to enable the GPIO driver for the DA9055 chip.
The Dialog DA9055 PMIC chip has 3 GPIO pins that can be
be controller by this driver.
If driver is built as a module it will be called gpio-da9055.
config [31mCONFIG_GPIO_DLN2[0m
tristate "Diolan DLN2 GPIO support"
depends on [31mCONFIG_MFD_DLN2[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Select this option to enable GPIO driver for the Diolan DLN2
board.
This driver can also be built as a module. If so, the module
will be called gpio-dln2.
config [31mCONFIG_HTC_EGPIO[0m
bool "HTC EGPIO support"
depends on [31mCONFIG_GPIOLIB[0m && [31mCONFIG_ARM[0m
help
This driver supports the CPLD egpio chip present on
several HTC phones. It provides basic support for input
pins, output pins, and irqs.
config [31mCONFIG_GPIO_JANZ_TTL[0m
tristate "Janz VMOD-TTL Digital IO Module"
depends on [31mCONFIG_MFD_JANZ_CMODIO[0m
help
This enables support for the Janz VMOD-TTL Digital IO module.
This driver provides support for driving the pins in output
mode only. Input mode is not supported.
config [31mCONFIG_GPIO_KEMPLD[0m
tristate "Kontron ETX / COMexpress GPIO"
depends on [31mCONFIG_MFD_KEMPLD[0m
help
This enables support for the PLD GPIO interface on some Kontron ETX
and COMexpress (ETXexpress) modules.
This driver can also be built as a module. If so, the module will be
called gpio-kempld.
config [31mCONFIG_GPIO_LP3943[0m
tristate "TI/National Semiconductor LP3943 GPIO expander"
depends on [31mCONFIG_MFD_LP3943[0m
help
GPIO driver for LP3943 MFD.
LP3943 can be used as a GPIO expander which provides up to 16 GPIOs.
Open drain outputs are required for this usage.
config [31mCONFIG_GPIO_LP873X[0m
tristate "TI LP873X GPO"
depends on [31mCONFIG_MFD_TI_LP873X[0m
help
This driver supports the GPO on TI Lp873x PMICs. 2 GPOs are present
on LP873X PMICs.
This driver can also be built as a module. If so, the module will be
called gpio-lp873x.
config [31mCONFIG_GPIO_MAX77620[0m
tristate "GPIO support for PMIC MAX77620 and MAX20024"
depends on [31mCONFIG_MFD_MAX77620[0m
help
GPIO driver for MAX77620 and MAX20024 PMIC from Maxim Semiconductor.
MAX77620 PMIC has 8 pins that can be configured as GPIOs. The
driver also provides interrupt support for each of the gpios.
Say yes here to enable the max77620 to be used as gpio controller.
config [31mCONFIG_GPIO_MSIC[0m
bool "Intel MSIC mixed signal gpio support"
depends on ([31mCONFIG_X86[0m || [31mCONFIG_COMPILE_TEST[0m) && [31mCONFIG_MFD_INTEL_MSIC[0m
help
Enable support for GPIO on intel MSIC controllers found in
intel MID devices
config [31mCONFIG_GPIO_PALMAS[0m
bool "TI PALMAS series PMICs GPIO"
depends on [31mCONFIG_MFD_PALMAS[0m
help
Select this option to enable GPIO driver for the TI PALMAS
series chip family.
config [31mCONFIG_GPIO_RC5T583[0m
bool "RICOH RC5T583 GPIO"
depends on [31mCONFIG_MFD_RC5T583[0m
help
Select this option to enable GPIO driver for the Ricoh RC5T583
chip family.
This driver provides the support for driving/reading the gpio pins
of RC5T583 device through standard gpio library.
config [31mCONFIG_GPIO_STMPE[0m
bool "STMPE GPIOs"
depends on [31mCONFIG_MFD_STMPE[0m
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
This enables support for the GPIOs found on the STMPE I/O
Expanders.
config [31mCONFIG_GPIO_TC3589X[0m
bool "TC3589X GPIOs"
depends on [31mCONFIG_MFD_TC3589X[0m
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
This enables support for the GPIOs found on the TC3589X
I/O Expander.
config [31mCONFIG_GPIO_TIMBERDALE[0m
bool "Support for timberdale GPIO IP"
depends on [31mCONFIG_MFD_TIMBERDALE[0m
---help---
Add support for the GPIO IP in the timberdale [31mCONFIG_FPGA[0m.
config [31mCONFIG_GPIO_TPS65086[0m
tristate "TI TPS65086 GPO"
depends on [31mCONFIG_MFD_TPS65086[0m
help
This driver supports the GPO on TI TPS65086x PMICs.
config [31mCONFIG_GPIO_TPS65218[0m
tristate "TPS65218 GPIO"
depends on [31mCONFIG_MFD_TPS65218[0m
help
Select this option to enable GPIO driver for the TPS65218
chip family.
config [31mCONFIG_GPIO_TPS6586X[0m
bool "TPS6586X GPIO"
depends on [31mCONFIG_MFD_TPS6586X[0m
help
Select this option to enable GPIO driver for the TPS6586X
chip family.
config [31mCONFIG_GPIO_TPS65910[0m
bool "TPS65910 GPIO"
depends on [31mCONFIG_MFD_TPS65910[0m
help
Select this option to enable GPIO driver for the TPS65910
chip family.
config [31mCONFIG_GPIO_TPS65912[0m
tristate "TI TPS65912 GPIO"
depends on [31mCONFIG_MFD_TPS65912[0m
help
This driver supports TPS65912 gpio chip
config [31mCONFIG_GPIO_TWL4030[0m
tristate "TWL4030, TWL5030, and TPS659x0 GPIOs"
depends on [31mCONFIG_TWL4030_CORE[0m
help
Say yes here to access the GPIO signals of various multi-function
power management chips from Texas Instruments.
config [31mCONFIG_GPIO_TWL6040[0m
tristate "TWL6040 GPO"
depends on [31mCONFIG_TWL6040_CORE[0m
help
Say yes here to access the GPO signals of twl6040
audio chip from Texas Instruments.
config [31mCONFIG_GPIO_UCB1400[0m
tristate "Philips UCB1400 GPIO"
depends on [31mCONFIG_UCB1400_CORE[0m
help
This enables support for the Philips UCB1400 GPIO pins.
The UCB1400 is an AC97 audio codec.
config [31mCONFIG_GPIO_WHISKEY_COVE[0m
tristate "GPIO support for Whiskey Cove PMIC"
depends on ([31mCONFIG_X86[0m || [31mCONFIG_COMPILE_TEST[0m) && [31mCONFIG_INTEL_SOC_PMIC[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Support for GPIO pins on Whiskey Cove PMIC.
Say Yes if you have a Intel SoC based tablet with Whiskey Cove PMIC
inside.
This driver can also be built as a module. If so, the module will be
called gpio-wcove.
config [31mCONFIG_GPIO_WM831X[0m
tristate "WM831x GPIOs"
depends on [31mCONFIG_MFD_WM831X[0m
help
Say yes here to access the GPIO signals of WM831x power management
chips from Wolfson Microelectronics.
config [31mCONFIG_GPIO_WM8350[0m
tristate "WM8350 GPIOs"
depends on [31mCONFIG_MFD_WM8350[0m
help
Say yes here to access the GPIO signals of WM8350 power management
chips from Wolfson Microelectronics.
config [31mCONFIG_GPIO_WM8994[0m
tristate "WM8994 GPIOs"
depends on [31mCONFIG_MFD_WM8994[0m
help
Say yes here to access the GPIO signals of WM8994 audio hub
CODECs from Wolfson Microelectronics.
endmenu
menu "PCI GPIO expanders"
depends on [31mCONFIG_PCI[0m
config [31mCONFIG_GPIO_AMD8111[0m
tristate "AMD 8111 GPIO driver"
depends on [31mCONFIG_X86[0m || [31mCONFIG_COMPILE_TEST[0m
help
The AMD 8111 south bridge contains 32 GPIO pins which can be used.
Note, that usually system firmware/[31mCONFIG_ACPI[0m handles GPIO pins on their
own and users might easily break their systems with uncarefull usage
of this driver!
If unsure, say N
config [31mCONFIG_GPIO_BT8XX[0m
tristate "BT8XX GPIO abuser"
depends on [31mCONFIG_VIDEO_BT848[0m=n
help
The BT8xx frame grabber chip has 24 GPIO pins that can be abused
as a cheap [31mCONFIG_PCI[0m GPIO card.
This chip can be found on Miro, Hauppauge and STB TV-cards.
The card needs to be physically altered for using it as a
GPIO card. For more information on how to build a GPIO card
from a BT8xx TV card, see the documentation file at
Documentation/bt8xxgpio.txt
If unsure, say N.
config [31mCONFIG_GPIO_INTEL_MID[0m
bool "Intel MID GPIO support"
depends on [31mCONFIG_X86_INTEL_MID[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say Y here to support Intel MID GPIO.
config [31mCONFIG_GPIO_MERRIFIELD[0m
tristate "Intel Merrifield GPIO support"
depends on [31mCONFIG_X86_INTEL_MID[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
Say Y here to support Intel Merrifield GPIO.
config [31mCONFIG_GPIO_ML_IOH[0m
tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
depends on [31mCONFIG_X86[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
help
ML7213 is companion chip for Intel Atom E6xx series.
This driver can be used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output
Hub) which is for IVI(In-Vehicle Infotainment) use.
This driver can access the IOH's GPIO device.
config [31mCONFIG_GPIO_PCH[0m
tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7223/ML7831) GPIO"
depends on [31mCONFIG_X86_32[0m || [31mCONFIG_MIPS[0m || [31mCONFIG_COMPILE_TEST[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
help
This driver is for PCH(Platform controller Hub) GPIO of Intel Topcliff
which is an IOH(Input/Output Hub) for x86 embedded processor.
This driver can access PCH GPIO device.
This driver also can be used for LAPIS Semiconductor IOH(Input/
Output Hub), ML7223 and ML7831.
ML7223 IOH is for MP(Media Phone) use.
ML7831 IOH is for general purpose use.
ML7223/ML7831 is companion chip for Intel Atom E6xx series.
ML7223/ML7831 is completely compatible for Intel EG20T PCH.
config [31mCONFIG_GPIO_RDC321X[0m
tristate "RDC R-321x GPIO support"
select [31mCONFIG_MFD_CORE[0m
select [31mCONFIG_MFD_RDC321X[0m
help
Support for the RDC R321x SoC GPIOs over southbridge
[31mCONFIG_PCI[0m configuration space.
config [31mCONFIG_GPIO_SODAVILLE[0m
bool "Intel Sodaville GPIO support"
depends on [31mCONFIG_X86[0m && [31mCONFIG_OF[0m
select [31mCONFIG_GPIO_GENERIC[0m
select [31mCONFIG_GENERIC_IRQ_CHIP[0m
help
Say Y here to support Intel Sodaville GPIO.
endmenu
menu "SPI GPIO expanders"
depends on [31mCONFIG_SPI_MASTER[0m
config [31mCONFIG_GPIO_74X164[0m
tristate "74x164 serial-in/parallel-out 8-bits shift register"
depends on [31mCONFIG_OF_GPIO[0m
help
Driver for 74x164 compatible serial-in/parallel-out 8-outputs
shift registers. This driver can be used to provide access
to more gpio outputs.
config [31mCONFIG_GPIO_MAX7301[0m
tristate "Maxim MAX7301 GPIO expander"
select [31mCONFIG_GPIO_MAX730X[0m
help
GPIO driver for Maxim MAX7301 [31mCONFIG_SPI[0m-based GPIO expander.
config [31mCONFIG_GPIO_MC33880[0m
tristate "Freescale MC33880 high-side/low-side switch"
help
[31mCONFIG_SPI[0m driver for Freescale MC33880 high-side/low-side switch.
This provides GPIO interface supporting inputs and outputs.
config [31mCONFIG_GPIO_PISOSR[0m
tristate "Generic parallel-in/serial-out shift register"
help
GPIO driver for [31mCONFIG_SPI[0m compatible parallel-in/serial-out shift
registers. These are input only devices.
endmenu
menu "SPI or I2C GPIO expanders"
depends on ([31mCONFIG_SPI_MASTER[0m && ![31mCONFIG_I2C[0m) || [31mCONFIG_I2C[0m
config [31mCONFIG_GPIO_MCP23S08[0m
tristate "Microchip MCP23xxx I/O expander"
depends on [31mCONFIG_OF_GPIO[0m
select [31mCONFIG_GPIOLIB_IRQCHIP[0m
help
[31mCONFIG_SPI[0m/[31mCONFIG_I2C[0m driver for Microchip MCP23S08/MCP23S17/MCP23008/MCP23017
I/O expanders.
This provides a GPIO interface supporting inputs and outputs.
The [31mCONFIG_I2C[0m versions of the chips can be used as interrupt-controller.
endmenu
menu "USB GPIO expanders"
depends on [31mCONFIG_USB[0m
config [31mCONFIG_GPIO_VIPERBOARD[0m
tristate "Viperboard GPIO a & b support"
depends on [31mCONFIG_MFD_VIPERBOARD[0m
help
Say yes here to access the GPIO signals of Nano River
Technologies Viperboard. There are two GPIO chips on the
board: gpioa and gpiob.
See viperboard API specification and Nano
River Tech's viperboard.h for detailed meaning
of the module parameters.
endmenu
endif