/*
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2003-2004 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>_
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/delay.h>
#include <linux/ktime.h>
#include <linux/uaccess.h>
#include <asm/io.h>
#include "prismcompat.h"
#include "isl_38xx.h"
#include "islpci_dev.h"
#include "islpci_mgt.h"
/******************************************************************************
Device Interface & Control functions
******************************************************************************/
/**
* isl38xx_disable_interrupts - disable all interrupts
* @device: pci memory base address
*
* Instructs the device to disable all interrupt reporting by asserting
* the IRQ line. New events may still show up in the interrupt identification
* register located at offset %ISL38XX_INT_IDENT_REG.
*/
void
isl38xx_disable_interrupts(void __iomem *device)
{
isl38xx_w32_flush(device, 0x00000000, ISL38XX_INT_EN_REG);
udelay(ISL38XX_WRITEIO_DELAY);
}
void
isl38xx_handle_sleep_request(isl38xx_control_block *control_block,
int *powerstate, void __iomem *device_base)
{
/* device requests to go into sleep mode
* check whether the transmit queues for data and management are empty */
if (isl38xx_in_queue(control_block, ISL38XX_CB_TX_DATA_LQ))
/* data tx queue not empty */
return;
if (isl38xx_in_queue(control_block, ISL38XX_CB_TX_MGMTQ))
/* management tx queue not empty */
return;
/* check also whether received frames are pending */
if (isl38xx_in_queue(control_block, ISL38XX_CB_RX_DATA_LQ))
/* data rx queue not empty */
return;
if (isl38xx_in_queue(control_block, ISL38XX_CB_RX_MGMTQ))
/* management rx queue not empty */
return;
#if VERBOSE > SHOW_ERROR_MESSAGES
DEBUG(SHOW_TRACING, "Device going to sleep mode\n");
#endif
/* all queues are empty, allow the device to go into sleep mode */
*powerstate = ISL38XX_PSM_POWERSAVE_STATE;
/* assert the Sleep interrupt in the Device Interrupt Register */
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_SLEEP,
ISL38XX_DEV_INT_REG);
udelay(ISL38XX_WRITEIO_DELAY);
}
void
isl38xx_handle_wakeup(isl38xx_control_block *control_block,
int *powerstate, void __iomem *device_base)
{
/* device is in active state, update the powerstate flag */
*powerstate = ISL38XX_PSM_ACTIVE_STATE;
/* now check whether there are frames pending for the card */
if (!isl38xx_in_queue(control_block, ISL38XX_CB_TX_DATA_LQ)
&& !isl38xx_in_queue(control_block, ISL38XX_CB_TX_MGMTQ))
return;
#if VERBOSE > SHOW_ERROR_MESSAGES
DEBUG(SHOW_ANYTHING, "Wake up handler trigger the device\n");
#endif
/* either data or management transmit queue has a frame pending
* trigger the device by setting the Update bit in the Device Int reg */
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_UPDATE,
ISL38XX_DEV_INT_REG);
udelay(ISL38XX_WRITEIO_DELAY);
}
void
isl38xx_trigger_device(int asleep, void __iomem *device_base)
{
u32 reg;
#if VERBOSE > SHOW_ERROR_MESSAGES
u32 counter = 0;
struct timespec64 current_ts64;
DEBUG(SHOW_FUNCTION_CALLS, "isl38xx trigger device\n");
#endif
/* check whether the device is in power save mode */
if (asleep) {
/* device is in powersave, trigger the device for wakeup */
#if VERBOSE > SHOW_ERROR_MESSAGES
ktime_get_real_ts64(¤t_ts64);
DEBUG(SHOW_TRACING, "%lld.%09ld Device wakeup triggered\n",
(s64)current_ts64.tv_sec, current_ts64.tv_nsec);
DEBUG(SHOW_TRACING, "%lld.%09ld Device register read %08x\n",
(s64)current_ts64.tv_sec, current_ts64.tv_nsec,
readl(device_base + ISL38XX_CTRL_STAT_REG));
#endif
reg = readl(device_base + ISL38XX_INT_IDENT_REG);
if (reg == 0xabadface) {
#if VERBOSE > SHOW_ERROR_MESSAGES
ktime_get_real_ts64(¤t_ts64);
DEBUG(SHOW_TRACING,
"%lld.%09ld Device register abadface\n",
(s64)current_ts64.tv_sec, current_ts64.tv_nsec);
#endif
/* read the Device Status Register until Sleepmode bit is set */
while (reg = readl(device_base + ISL38XX_CTRL_STAT_REG),
(reg & ISL38XX_CTRL_STAT_SLEEPMODE) == 0) {
udelay(ISL38XX_WRITEIO_DELAY);
#if VERBOSE > SHOW_ERROR_MESSAGES
counter++;
#endif
}
#if VERBOSE > SHOW_ERROR_MESSAGES
DEBUG(SHOW_TRACING,
"%lld.%09ld Device register read %08x\n",
(s64)current_ts64.tv_sec, current_ts64.tv_nsec,
readl(device_base + ISL38XX_CTRL_STAT_REG));
ktime_get_real_ts64(¤t_ts64);
DEBUG(SHOW_TRACING,
"%lld.%09ld Device asleep counter %i\n",
(s64)current_ts64.tv_sec, current_ts64.tv_nsec,
counter);
#endif
}
/* assert the Wakeup interrupt in the Device Interrupt Register */
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_WAKEUP,
ISL38XX_DEV_INT_REG);
#if VERBOSE > SHOW_ERROR_MESSAGES
udelay(ISL38XX_WRITEIO_DELAY);
/* perform another read on the Device Status Register */
reg = readl(device_base + ISL38XX_CTRL_STAT_REG);
ktime_get_real_ts64(¤t_ts64);
DEBUG(SHOW_TRACING, "%lld.%00ld Device register read %08x\n",
(s64)current_ts64.tv_sec, current_ts64.tv_nsec, reg);
#endif
} else {
/* device is (still) awake */
#if VERBOSE > SHOW_ERROR_MESSAGES
DEBUG(SHOW_TRACING, "Device is in active state\n");
#endif
/* trigger the device by setting the Update bit in the Device Int reg */
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_UPDATE,
ISL38XX_DEV_INT_REG);
}
}
void
isl38xx_interface_reset(void __iomem *device_base, dma_addr_t host_address)
{
#if VERBOSE > SHOW_ERROR_MESSAGES
DEBUG(SHOW_FUNCTION_CALLS, "isl38xx_interface_reset\n");
#endif
/* load the address of the control block in the device */
isl38xx_w32_flush(device_base, host_address, ISL38XX_CTRL_BLK_BASE_REG);
udelay(ISL38XX_WRITEIO_DELAY);
/* set the reset bit in the Device Interrupt Register */
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_RESET, ISL38XX_DEV_INT_REG);
udelay(ISL38XX_WRITEIO_DELAY);
/* enable the interrupt for detecting initialization */
/* Note: Do not enable other interrupts here. We want the
* device to have come up first 100% before allowing any other
* interrupts. */
isl38xx_w32_flush(device_base, ISL38XX_INT_IDENT_INIT, ISL38XX_INT_EN_REG);
udelay(ISL38XX_WRITEIO_DELAY); /* allow complete full reset */
}
void
isl38xx_enable_common_interrupts(void __iomem *device_base)
{
u32 reg;
reg = ISL38XX_INT_IDENT_UPDATE | ISL38XX_INT_IDENT_SLEEP |
ISL38XX_INT_IDENT_WAKEUP;
isl38xx_w32_flush(device_base, reg, ISL38XX_INT_EN_REG);
udelay(ISL38XX_WRITEIO_DELAY);
}
int
isl38xx_in_queue(isl38xx_control_block *cb, int queue)
{
const s32 delta = (le32_to_cpu(cb->driver_curr_frag[queue]) -
le32_to_cpu(cb->device_curr_frag[queue]));
/* determine the amount of fragments in the queue depending on the type
* of the queue, either transmit or receive */
BUG_ON(delta < 0); /* driver ptr must be ahead of device ptr */
switch (queue) {
/* send queues */
case ISL38XX_CB_TX_MGMTQ:
BUG_ON(delta > ISL38XX_CB_MGMT_QSIZE);
case ISL38XX_CB_TX_DATA_LQ:
case ISL38XX_CB_TX_DATA_HQ:
BUG_ON(delta > ISL38XX_CB_TX_QSIZE);
return delta;
/* receive queues */
case ISL38XX_CB_RX_MGMTQ:
BUG_ON(delta > ISL38XX_CB_MGMT_QSIZE);
return ISL38XX_CB_MGMT_QSIZE - delta;
case ISL38XX_CB_RX_DATA_LQ:
case ISL38XX_CB_RX_DATA_HQ:
BUG_ON(delta > ISL38XX_CB_RX_QSIZE);
return ISL38XX_CB_RX_QSIZE - delta;
}
BUG();
return 0;
}