config [31mCONFIG_SND_BF5XX_I2S[0m
tristate "SoC I2S Audio for the ADI Blackfin chip"
depends on [31mCONFIG_BLACKFIN[0m
select [31mCONFIG_SND_BF5XX_SOC_SPORT[0m if ![31mCONFIG_BF60x[0m
select [31mCONFIG_SND_BF6XX_SOC_SPORT[0m if [31mCONFIG_BF60x[0m
help
Say Y or [31mCONFIG_M[0m if you want to add support for codecs attached to
the Blackfin SPORT (synchronous serial ports) interface in I2S
mode (supports single stereo In/Out).
You will also need to select the audio interfaces to support below.
config [31mCONFIG_SND_BF5XX_SOC_SSM2602[0m
tristate "SoC SSM2602 Audio Codec Add-On Card support"
depends on [31mCONFIG_SND_BF5XX_I2S[0m && [31mCONFIG_SND_SOC_I2C_AND_SPI[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m if ![31mCONFIG_BF60x[0m
select [31mCONFIG_SND_BF6XX_SOC_I2S[0m if [31mCONFIG_BF60x[0m
select [31mCONFIG_SND_SOC_SSM2602_SPI[0m if [31mCONFIG_SPI_MASTER[0m
select [31mCONFIG_SND_SOC_SSM2602_I2C[0m if [31mCONFIG_I2C[0m
help
Say Y if you want to add support for the Analog Devices
SSM2602 Audio Codec Add-On Card.
config [31mCONFIG_SND_SOC_BFIN_EVAL_ADAU1701[0m
tristate "Support for the EVAL-ADAU1701MINIZ board on Blackfin eval boards"
depends on [31mCONFIG_SND_BF5XX_I2S[0m && [31mCONFIG_I2C[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m
select [31mCONFIG_SND_SOC_ADAU1701[0m
help
Say Y if you want to add support for the Analog Devices EVAL-ADAU1701MINIZ
board connected to one of the Blackfin evaluation boards like the
BF5XX-STAMP or BF5XX-EZKIT.
config [31mCONFIG_SND_SOC_BFIN_EVAL_ADAU1373[0m
tristate "Support for the EVAL-ADAU1373 board on Blackfin eval boards"
depends on [31mCONFIG_SND_BF5XX_I2S[0m && [31mCONFIG_I2C[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m
select [31mCONFIG_SND_SOC_ADAU1373[0m
help
Say Y if you want to add support for the Analog Devices EVAL-ADAU1373
board connected to one of the Blackfin evaluation boards like the
BF5XX-STAMP or BF5XX-EZKIT.
Note: This driver assumes that first ADAU1373 DAI is connected to the
first SPORT port on the BF5XX board.
config [31mCONFIG_SND_SOC_BFIN_EVAL_ADAU1X61[0m
tristate "Support for the EVAL-ADAU1X61 board on Blackfin eval boards"
depends on [31mCONFIG_SND_BF5XX_I2S[0m && [31mCONFIG_I2C[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m
select [31mCONFIG_SND_SOC_ADAU1761_I2C[0m
help
Say Y if you want to add support for the Analog Devices EVAL-ADAU1X61
board connected to one of the Blackfin evaluation boards like the
BF5XX-STAMP or BF5XX-EZKIT.
Note: This driver assumes that the ADAU1X61 is connected to the
first SPORT port on the BF5XX board.
config [31mCONFIG_SND_SOC_BFIN_EVAL_ADAU1X81[0m
tristate "Support for the EVAL-ADAU1X81 boards on Blackfin eval boards"
depends on [31mCONFIG_SND_BF5XX_I2S[0m && [31mCONFIG_I2C[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m
select [31mCONFIG_SND_SOC_ADAU1781_I2C[0m
help
Say Y if you want to add support for the Analog Devices EVAL-ADAU1X81
board connected to one of the Blackfin evaluation boards like the
BF5XX-STAMP or BF5XX-EZKIT.
Note: This driver assumes that the ADAU1X81 is connected to the
first SPORT port on the BF5XX board.
config [31mCONFIG_SND_SOC_BFIN_EVAL_ADAV80X[0m
tristate "Support for the EVAL-ADAV80X boards on Blackfin eval boards"
depends on [31mCONFIG_SND_BF5XX_I2S[0m && [31mCONFIG_SND_SOC_I2C_AND_SPI[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m
select [31mCONFIG_SND_SOC_ADAV801[0m if [31mCONFIG_SPI_MASTER[0m
select [31mCONFIG_SND_SOC_ADAV803[0m if [31mCONFIG_I2C[0m
help
Say Y if you want to add support for the Analog Devices EVAL-ADAV801 or
EVAL-ADAV803 board connected to one of the Blackfin evaluation boards
like the BF5XX-STAMP or BF5XX-EZKIT.
Note: This driver assumes that the ADAV80X digital record and playback
interfaces are connected to the first SPORT port on the BF5XX board.
config [31mCONFIG_SND_BF5XX_SOC_AD1836[0m
tristate "SoC AD1836 Audio support for BF5xx"
depends on [31mCONFIG_SND_BF5XX_I2S[0m && [31mCONFIG_SPI_MASTER[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m
select [31mCONFIG_SND_SOC_AD1836[0m
help
Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.
config [31mCONFIG_SND_BF5XX_SOC_AD193X[0m
tristate "SoC AD193X Audio support for Blackfin"
depends on [31mCONFIG_SND_BF5XX_I2S[0m && [31mCONFIG_SND_SOC_I2C_AND_SPI[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m
select [31mCONFIG_SND_SOC_AD193X_I2C[0m if [31mCONFIG_I2C[0m
select [31mCONFIG_SND_SOC_AD193X_SPI[0m if [31mCONFIG_SPI_MASTER[0m
help
Say Y if you want to add support for AD193X codec on Blackfin.
This driver supports AD1936, AD1937, AD1938 and AD1939.
config [31mCONFIG_SND_BF5XX_SOC_AD73311[0m
tristate "SoC AD73311 Audio support for Blackfin"
depends on [31mCONFIG_SND_BF5XX_I2S[0m
select [31mCONFIG_SND_BF5XX_SOC_I2S[0m
select [31mCONFIG_SND_SOC_AD73311[0m
help
Say Y if you want to add support for AD73311 codec on Blackfin.
config [31mCONFIG_SND_BFIN_AD73311_SE[0m
int "PF pin for AD73311L Chip Select"
depends on [31mCONFIG_SND_BF5XX_SOC_AD73311[0m
default 4
help
Enter the GPIO used to control AD73311's SE pin. Acceptable
values are 0 to 7
config [31mCONFIG_SND_BF5XX_AC97[0m
tristate "SoC AC97 Audio for the ADI BF5xx chip"
depends on [31mCONFIG_BLACKFIN[0m
select [31mCONFIG_AC97_BUS[0m
select [31mCONFIG_SND_SOC_AC97_BUS[0m
select [31mCONFIG_SND_BF5XX_SOC_SPORT[0m
select [31mCONFIG_SND_BF5XX_SOC_AC97[0m
help
Say Y or [31mCONFIG_M[0m if you want to add support for codecs attached to
the Blackfin SPORT (synchronous serial ports) interface in slot 16
mode (pseudo AC97 interface).
You will also need to select the audio interfaces to support below.
Note:
AC97 codecs which do not implement the slot-16 mode will not function
properly with this driver. This driver is known to work with the
Analog Devices line of AC97 codecs.
config [31mCONFIG_SND_BF5XX_MMAP_SUPPORT[0m
bool "Enable MMAP Support"
depends on [31mCONFIG_SND_BF5XX_AC97[0m
default y
help
Say y if you want AC97 driver to support mmap mode.
We introduce an intermediate buffer to simulate mmap.
config [31mCONFIG_SND_BF5XX_MULTICHAN_SUPPORT[0m
bool "Enable Multichannel Support"
depends on [31mCONFIG_SND_BF5XX_AC97[0m
default n
help
Say y if you want AC97 driver to support up to 5.1 channel audio.
this mode will consume much more memory for DMA.
config [31mCONFIG_SND_BF5XX_HAVE_COLD_RESET[0m
bool "BOARD has COLD Reset GPIO"
depends on [31mCONFIG_SND_BF5XX_AC97[0m
default y if [31mCONFIG_BFIN548_EZKIT[0m
default n if ![31mCONFIG_BFIN548_EZKIT[0m
config [31mCONFIG_SND_BF5XX_RESET_GPIO_NUM[0m
int "Set a GPIO for cold reset"
depends on [31mCONFIG_SND_BF5XX_HAVE_COLD_RESET[0m
range 0 159
default 19 if [31mCONFIG_BFIN548_EZKIT[0m
default 5 if [31mCONFIG_BFIN537_STAMP[0m
default 0
help
Set the correct GPIO for RESET the sound chip.
config [31mCONFIG_SND_BF5XX_SOC_AD1980[0m
tristate "SoC AD1980/1 Audio support for BF5xx (Obsolete)"
depends on [31mCONFIG_SND_BF5XX_AC97[0m
select [31mCONFIG_SND_BF5XX_SOC_AC97[0m
select [31mCONFIG_SND_SOC_AD1980[0m
help
Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.
Warning:
Because Analog Devices Inc. discontinued the ad1980 sound chip since
Sep. 2009, this ad1980 driver is not maintained, tested and supported
by [31mCONFIG_ADI[0m now.
config [31mCONFIG_SND_BF5XX_SOC_SPORT[0m
tristate
config [31mCONFIG_SND_BF6XX_SOC_SPORT[0m
tristate
config [31mCONFIG_SND_BF5XX_SOC_I2S[0m
tristate
config [31mCONFIG_SND_BF6XX_SOC_I2S[0m
tristate
config [31mCONFIG_SND_BF5XX_SOC_AC97[0m
tristate
config [31mCONFIG_SND_BF5XX_SPORT_NUM[0m
int "Set a SPORT for Sound chip"
depends on ([31mCONFIG_SND_BF5XX_SOC_SPORT[0m || [31mCONFIG_SND_BF6XX_SOC_SPORT[0m)
range 0 3 if [31mCONFIG_BF54x[0m
range 0 1 if ![31mCONFIG_BF54x[0m
default 0
help
Set the correct SPORT for sound chip.