/*
* Copyright (c) 2003-2014 Broadcom Corporation
* All Rights Reserved
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
* General Public License (GPL) Version 2, available from the file
* COPYING in the main directory of this source tree, or the Broadcom
* license below:
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
*
* THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
* BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
* WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
* OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
* IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <linux/dma-mapping.h>
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/irq.h>
#include <linux/bitops.h>
#include <asm/cpu.h>
#include <asm/mipsregs.h>
#include <asm/netlogic/haldefs.h>
#include <asm/netlogic/xlp-hal/xlp.h>
#include <asm/netlogic/common.h>
#include <asm/netlogic/xlp-hal/iomap.h>
#include <asm/netlogic/mips-extns.h>
#define SATA_CTL 0x0
#define SATA_STATUS 0x1 /* Status Reg */
#define SATA_INT 0x2 /* Interrupt Reg */
#define SATA_INT_MASK 0x3 /* Interrupt Mask Reg */
#define SATA_CR_REG_TIMER 0x4 /* PHY Conrol Timer Reg */
#define SATA_CORE_ID 0x5 /* Core ID Reg */
#define SATA_AXI_SLAVE_OPT1 0x6 /* AXI Slave Options Reg */
#define SATA_PHY_LOS_LEV 0x7 /* PHY LOS Level Reg */
#define SATA_PHY_MULTI 0x8 /* PHY Multiplier Reg */
#define SATA_PHY_CLK_SEL 0x9 /* Clock Select Reg */
#define SATA_PHY_AMP1_GEN1 0xa /* PHY Transmit Amplitude Reg 1 */
#define SATA_PHY_AMP1_GEN2 0xb /* PHY Transmit Amplitude Reg 2 */
#define SATA_PHY_AMP1_GEN3 0xc /* PHY Transmit Amplitude Reg 3 */
#define SATA_PHY_PRE1 0xd /* PHY Transmit Preemphasis Reg 1 */
#define SATA_PHY_PRE2 0xe /* PHY Transmit Preemphasis Reg 2 */
#define SATA_PHY_PRE3 0xf /* PHY Transmit Preemphasis Reg 3 */
#define SATA_SPDMODE 0x10 /* Speed Mode Reg */
#define SATA_REFCLK 0x11 /* Reference Clock Control Reg */
#define SATA_BYTE_SWAP_DIS 0x12 /* byte swap disable */
/*SATA_CTL Bits */
#define SATA_RST_N BIT(0)
#define PHY0_RESET_N BIT(16)
#define PHY1_RESET_N BIT(17)
#define PHY2_RESET_N BIT(18)
#define PHY3_RESET_N BIT(19)
#define M_CSYSREQ BIT(2)
#define S_CSYSREQ BIT(3)
/*SATA_STATUS Bits */
#define P0_PHY_READY BIT(4)
#define P1_PHY_READY BIT(5)
#define P2_PHY_READY BIT(6)
#define P3_PHY_READY BIT(7)
#define nlm_read_sata_reg(b, r) nlm_read_reg(b, r)
#define nlm_write_sata_reg(b, r, v) nlm_write_reg(b, r, v)
#define nlm_get_sata_pcibase(node) \
nlm_pcicfg_base(XLP_IO_SATA_OFFSET(node))
/* SATA device specific configuration registers are starts at 0x900 offset */
#define nlm_get_sata_regbase(node) \
(nlm_get_sata_pcibase(node) + 0x900)
static void sata_clear_glue_reg(uint64_t regbase, uint32_t off, uint32_t bit)
{
uint32_t reg_val;
reg_val = nlm_read_sata_reg(regbase, off);
nlm_write_sata_reg(regbase, off, (reg_val & ~bit));
}
static void sata_set_glue_reg(uint64_t regbase, uint32_t off, uint32_t bit)
{
uint32_t reg_val;
reg_val = nlm_read_sata_reg(regbase, off);
nlm_write_sata_reg(regbase, off, (reg_val | bit));
}
static void nlm_sata_firmware_init(int node)
{
uint32_t reg_val;
uint64_t regbase;
int i;
pr_info("XLP AHCI Initialization started.\n");
regbase = nlm_get_sata_regbase(node);
/* Reset SATA */
sata_clear_glue_reg(regbase, SATA_CTL, SATA_RST_N);
/* Reset PHY */
sata_clear_glue_reg(regbase, SATA_CTL,
(PHY3_RESET_N | PHY2_RESET_N
| PHY1_RESET_N | PHY0_RESET_N));
/* Set SATA */
sata_set_glue_reg(regbase, SATA_CTL, SATA_RST_N);
/* Set PHY */
sata_set_glue_reg(regbase, SATA_CTL,
(PHY3_RESET_N | PHY2_RESET_N
| PHY1_RESET_N | PHY0_RESET_N));
pr_debug("Waiting for PHYs to come up.\n");
i = 0;
do {
reg_val = nlm_read_sata_reg(regbase, SATA_STATUS);
i++;
} while (((reg_val & 0xF0) != 0xF0) && (i < 10000));
for (i = 0; i < 4; i++) {
if (reg_val & (P0_PHY_READY << i))
pr_info("PHY%d is up.\n", i);
else
pr_info("PHY%d is down.\n", i);
}
pr_info("XLP AHCI init done.\n");
}
static int __init nlm_ahci_init(void)
{
int node = 0;
int chip = read_c0_prid() & PRID_IMP_MASK;
if (chip == PRID_IMP_NETLOGIC_XLP3XX)
nlm_sata_firmware_init(node);
return 0;
}
static void nlm_sata_intr_ack(struct irq_data *data)
{
uint32_t val = 0;
uint64_t regbase;
regbase = nlm_get_sata_regbase(nlm_nodeid());
val = nlm_read_sata_reg(regbase, SATA_INT);
sata_set_glue_reg(regbase, SATA_INT, val);
}
static void nlm_sata_fixup_bar(struct pci_dev *dev)
{
/*
* The AHCI resource is in BAR 0, move it to
* BAR 5, where it is expected
*/
dev->resource[5] = dev->resource[0];
memset(&dev->resource[0], 0, sizeof(dev->resource[0]));
}
static void nlm_sata_fixup_final(struct pci_dev *dev)
{
uint32_t val;
uint64_t regbase;
int node = 0; /* XLP3XX does not support multi-node */
regbase = nlm_get_sata_regbase(node);
/* clear pending interrupts and then enable them */
val = nlm_read_sata_reg(regbase, SATA_INT);
sata_set_glue_reg(regbase, SATA_INT, val);
/* Mask the core interrupt. If all the interrupts
* are enabled there are spurious interrupt flow
* happening, to avoid only enable core interrupt
* mask.
*/
sata_set_glue_reg(regbase, SATA_INT_MASK, 0x1);
dev->irq = PIC_SATA_IRQ;
nlm_set_pic_extra_ack(node, PIC_SATA_IRQ, nlm_sata_intr_ack);
}
arch_initcall(nlm_ahci_init);
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_SATA,
nlm_sata_fixup_bar);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_SATA,
nlm_sata_fixup_final);