/*
* MPC85xx setup and early boot code plus other random bits.
*
* Maintained by Kumar Gala (see MAINTAINERS for contact information)
*
* Copyright 2005, 2011-2012 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/stddef.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/reboot.h>
#include <linux/pci.h>
#include <linux/kdev_t.h>
#include <linux/major.h>
#include <linux/console.h>
#include <linux/delay.h>
#include <linux/seq_file.h>
#include <linux/initrd.h>
#include <linux/interrupt.h>
#include <linux/fsl_devices.h>
#include <linux/of_platform.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <linux/atomic.h>
#include <asm/time.h>
#include <asm/io.h>
#include <asm/machdep.h>
#include <asm/ipic.h>
#include <asm/pci-bridge.h>
#include <asm/irq.h>
#include <mm/mmu_decl.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/mpic.h>
#include <asm/i8259.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
#include "mpc85xx.h"
/*
* The CDS board contains an FPGA/CPLD called "Cadmus", which collects
* various logic and performs system control functions.
* Here is the FPGA/CPLD register map.
*/
struct cadmus_reg {
u8 cm_ver; /* Board version */
u8 cm_csr; /* General control/status */
u8 cm_rst; /* Reset control */
u8 cm_hsclk; /* High speed clock */
u8 cm_hsxclk; /* High speed clock extended */
u8 cm_led; /* LED data */
u8 cm_pci; /* PCI control/status */
u8 cm_dma; /* DMA control */
u8 res[248]; /* Total 256 bytes */
};
static struct cadmus_reg *cadmus;
#ifdef [31mCONFIG_PCI[0m
#define ARCADIA_HOST_BRIDGE_IDSEL 17
#define ARCADIA_2ND_BRIDGE_IDSEL 3
static int mpc85xx_exclude_device(struct pci_controller *hose,
u_char bus, u_char devfn)
{
/* We explicitly do not go past the Tundra 320 Bridge */
if ((bus == 1) && (PCI_SLOT(devfn) == ARCADIA_2ND_BRIDGE_IDSEL))
return PCIBIOS_DEVICE_NOT_FOUND;
if ((bus == 0) && (PCI_SLOT(devfn) == ARCADIA_2ND_BRIDGE_IDSEL))
return PCIBIOS_DEVICE_NOT_FOUND;
else
return PCIBIOS_SUCCESSFUL;
}
static int mpc85xx_cds_restart(struct notifier_block *this,
unsigned long mode, void *cmd)
{
struct pci_dev *dev;
u_char tmp;
if ((dev = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686,
NULL))) {
/* Use the VIA Super Southbridge to force a PCI reset */
pci_read_config_byte(dev, 0x47, &tmp);
pci_write_config_byte(dev, 0x47, tmp | 1);
/* Flush the outbound PCI write queues */
pci_read_config_byte(dev, 0x47, &tmp);
/*
* At this point, the hardware reset should have triggered.
* However, if it doesn't work for some mysterious reason,
* just fall through to the default reset below.
*/
pci_dev_put(dev);
}
/*
* If we can't find the VIA chip (maybe the P2P bridge is
* disabled) or the VIA chip reset didn't work, just return
* and let default reset sequence happen.
*/
return NOTIFY_DONE;
}
static int mpc85xx_cds_restart_register(void)
{
static struct notifier_block restart_handler;
restart_handler.notifier_call = mpc85xx_cds_restart;
restart_handler.priority = 192;
return register_restart_handler(&restart_handler);
}
machine_arch_initcall(mpc85xx_cds, mpc85xx_cds_restart_register);
static void __init mpc85xx_cds_pci_irq_fixup(struct pci_dev *dev)
{
u_char c;
if (dev->vendor == PCI_VENDOR_ID_VIA) {
switch (dev->device) {
case PCI_DEVICE_ID_VIA_82C586_1:
/*
* U-Boot does not set the enable bits
* for the IDE device. Force them on here.
*/
pci_read_config_byte(dev, 0x40, &c);
c |= 0x03; /* IDE: Chip Enable Bits */
pci_write_config_byte(dev, 0x40, c);
/*
* Since only primary interface works, force the
* IDE function to standard primary IDE interrupt
* w/ 8259 offset
*/
dev->irq = 14;
pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq);
break;
/*
* Force legacy USB interrupt routing
*/
case PCI_DEVICE_ID_VIA_82C586_2:
/* There are two USB controllers.
* Identify them by functon number
*/
if (PCI_FUNC(dev->devfn) == 3)
dev->irq = 11;
else
dev->irq = 10;
pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq);
default:
break;
}
}
}
static void skip_fake_bridge(struct pci_dev *dev)
{
/* Make it an error to skip the fake bridge
* in pci_setup_device() in probe.c */
dev->hdr_type = 0x7f;
}
DECLARE_PCI_FIXUP_EARLY(0x1957, 0x3fff, skip_fake_bridge);
DECLARE_PCI_FIXUP_EARLY(0x3fff, 0x1957, skip_fake_bridge);
DECLARE_PCI_FIXUP_EARLY(0xff3f, 0x5719, skip_fake_bridge);
#define PCI_DEVICE_ID_IDT_TSI310 0x01a7
/*
* Fix Tsi310 PCI-X bridge resource.
* Force the bridge to open a window from 0x0000-0x1fff in PCI I/O space.
* This allows legacy I/O(i8259, etc) on the VIA southbridge to be accessed.
*/
void mpc85xx_cds_fixup_bus(struct pci_bus *bus)
{
struct pci_dev *dev = bus->self;
struct resource *res = bus->resource[0];
if (dev != NULL &&
dev->vendor == PCI_VENDOR_ID_IBM &&
dev->device == PCI_DEVICE_ID_IDT_TSI310) {
if (res) {
res->start = 0;
res->end = 0x1fff;
res->flags = IORESOURCE_IO;
pr_info("mpc85xx_cds: PCI bridge resource fixup applied\n");
pr_info("mpc85xx_cds: %pR\n", res);
}
}
fsl_pcibios_fixup_bus(bus);
}
#ifdef [31mCONFIG_PPC_I8259[0m
static void mpc85xx_8259_cascade_handler(struct irq_desc *desc)
{
unsigned int cascade_irq = i8259_irq();
if (cascade_irq)
/* handle an interrupt from the 8259 */
generic_handle_irq(cascade_irq);
/* check for any interrupts from the shared IRQ line */
handle_fasteoi_irq(desc);
}
static irqreturn_t mpc85xx_8259_cascade_action(int irq, void *dev_id)
{
return IRQ_HANDLED;
}
static struct irqaction mpc85xxcds_8259_irqaction = {
.handler = mpc85xx_8259_cascade_action,
.flags = IRQF_SHARED | IRQF_NO_THREAD,
.name = "8259 cascade",
};
#endif /* PPC_I8259 */
#endif /* CONFIG_PCI */
static void __init mpc85xx_cds_pic_init(void)
{
struct mpic *mpic;
mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN,
0, 256, " OpenPIC ");
BUG_ON(mpic == NULL);
mpic_init(mpic);
}
#if defined([31mCONFIG_PPC_I8259[0m) && defined([31mCONFIG_PCI[0m)
static int mpc85xx_cds_8259_attach(void)
{
int ret;
struct device_node *np = NULL;
struct device_node *cascade_node = NULL;
int cascade_irq;
/* Initialize the i8259 controller */
for_each_node_by_type(np, "interrupt-controller")
if (of_device_is_compatible(np, "chrp,iic")) {
cascade_node = np;
break;
}
if (cascade_node == NULL) {
printk(KERN_DEBUG "Could not find i8259 PIC\n");
return -ENODEV;
}
cascade_irq = irq_of_parse_and_map(cascade_node, 0);
if (!cascade_irq) {
printk(KERN_ERR "Failed to map cascade interrupt\n");
return -ENXIO;
}
i8259_init(cascade_node, 0);
of_node_put(cascade_node);
/*
* Hook the interrupt to make sure desc->action is never NULL.
* This is required to ensure that the interrupt does not get
* disabled when the last user of the shared IRQ line frees their
* interrupt.
*/
if ((ret = setup_irq(cascade_irq, &mpc85xxcds_8259_irqaction))) {
printk(KERN_ERR "Failed to setup cascade interrupt\n");
return ret;
}
/* Success. Connect our low-level cascade handler. */
irq_set_handler(cascade_irq, mpc85xx_8259_cascade_handler);
return 0;
}
machine_device_initcall(mpc85xx_cds, mpc85xx_cds_8259_attach);
#endif /* CONFIG_PPC_I8259 */
static void mpc85xx_cds_pci_assign_primary(void)
{
#ifdef [31mCONFIG_PCI[0m
struct device_node *np;
if (fsl_pci_primary)
return;
/*
* MPC85xx_CDS has ISA bridge but unfortunately there is no
* isa node in device tree. We now looking for i8259 node as
* a workaround for such a broken device tree. This routine
* is for complying to all device trees.
*/
np = of_find_node_by_name(NULL, "i8259");
while ((fsl_pci_primary = of_get_parent(np))) {
of_node_put(np);
np = fsl_pci_primary;
if ((of_device_is_compatible(np, "fsl,mpc8540-pci") ||
of_device_is_compatible(np, "fsl,mpc8548-pcie")) &&
of_device_is_available(np))
return;
}
#endif
}
/*
* Setup the architecture
*/
static void __init mpc85xx_cds_setup_arch(void)
{
struct device_node *np;
int cds_pci_slot;
if (ppc_md.progress)
ppc_md.progress("mpc85xx_cds_setup_arch()", 0);
np = of_find_compatible_node(NULL, NULL, "fsl,mpc8548cds-fpga");
if (!np) {
pr_err("Could not find FPGA node.\n");
return;
}
cadmus = of_iomap(np, 0);
of_node_put(np);
if (!cadmus) {
pr_err("Fail to map FPGA area.\n");
return;
}
if (ppc_md.progress) {
char buf[40];
cds_pci_slot = ((in_8(&cadmus->cm_csr) >> 6) & 0x3) + 1;
snprintf(buf, 40, "CDS Version = 0x%x in slot %d\n",
in_8(&cadmus->cm_ver), cds_pci_slot);
ppc_md.progress(buf, 0);
}
#ifdef [31mCONFIG_PCI[0m
ppc_md.pci_irq_fixup = mpc85xx_cds_pci_irq_fixup;
ppc_md.pci_exclude_device = mpc85xx_exclude_device;
#endif
mpc85xx_cds_pci_assign_primary();
fsl_pci_assign_primary();
}
static void mpc85xx_cds_show_cpuinfo(struct seq_file *m)
{
uint pvid, svid, phid1;
pvid = mfspr(SPRN_PVR);
svid = mfspr(SPRN_SVR);
seq_printf(m, "Vendor\t\t: Freescale Semiconductor\n");
seq_printf(m, "Machine\t\t: MPC85xx CDS (0x%x)\n",
in_8(&cadmus->cm_ver));
seq_printf(m, "PVR\t\t: 0x%x\n", pvid);
seq_printf(m, "SVR\t\t: 0x%x\n", svid);
/* Display cpu Pll setting */
phid1 = mfspr(SPRN_HID1);
seq_printf(m, "PLL setting\t: 0x%x\n", ((phid1 >> 24) & 0x3f));
}
/*
* Called very early, device-tree isn't unflattened
*/
static int __init mpc85xx_cds_probe(void)
{
return of_machine_is_compatible("MPC85xxCDS");
}
machine_arch_initcall(mpc85xx_cds, mpc85xx_common_publish_devices);
define_machine(mpc85xx_cds) {
.name = "MPC85xx CDS",
.probe = mpc85xx_cds_probe,
.setup_arch = mpc85xx_cds_setup_arch,
.init_IRQ = mpc85xx_cds_pic_init,
.show_cpuinfo = mpc85xx_cds_show_cpuinfo,
.get_irq = mpic_get_irq,
#ifdef [31mCONFIG_PCI[0m
.pcibios_fixup_bus = mpc85xx_cds_fixup_bus,
.pcibios_fixup_phb = fsl_pcibios_fixup_phb,
#endif
.calibrate_decr = generic_calibrate_decr,
.progress = udbg_progress,
};