Training courses

Kernel and Embedded Linux

Bootlin training courses

Embedded Linux, kernel,
Yocto Project, Buildroot, real-time,
graphics, boot time, debugging...

Bootlin logo

Elixir Cross Referencer

Open Menu /Documentation/leds/leds-class-flash.txt 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73

Flash LED handling under Linux
==============================

Some LED devices provide two modes - torch and flash. In the LED subsystem
those modes are supported by LED class (see Documentation/leds/leds-class.txt)
and LED Flash class respectively. The torch mode related features are enabled
by default and the flash ones only if a driver declares it by setting
LED_DEV_CAP_FLASH flag.

In order to enable the support for flash LEDs CONFIG_LEDS_CLASS_FLASH symbol
must be defined in the kernel config. A LED Flash class driver must be
registered in the LED subsystem with led_classdev_flash_register function.

Following sysfs attributes are exposed for controlling flash LED devices:
(see Documentation/ABI/testing/sysfs-class-led-flash)
	- flash_brightness
	- max_flash_brightness
	- flash_timeout
	- max_flash_timeout
	- flash_strobe
	- flash_fault


V4L2 flash wrapper for flash LEDs
=================================

A LED subsystem driver can be controlled also from the level of VideoForLinux2
subsystem. In order to enable this CONFIG_V4L2_FLASH_LED_CLASS symbol has to
be defined in the kernel config.

The driver must call the v4l2_flash_init function to get registered in the
V4L2 subsystem. The function takes six arguments:
- dev       : flash device, e.g. an I2C device
- of_node   : of_node of the LED, may be NULL if the same as device's
- fled_cdev : LED flash class device to wrap
- iled_cdev : LED flash class device representing indicator LED associated with
	      fled_cdev, may be NULL
- ops : V4L2 specific ops
	* external_strobe_set - defines the source of the flash LED strobe -
		V4L2_CID_FLASH_STROBE control or external source, typically
		a sensor, which makes it possible to synchronise the flash
		strobe start with exposure start,
	* intensity_to_led_brightness and led_brightness_to_intensity - perform
		enum led_brightness <-> V4L2 intensity conversion in a device
		specific manner - they can be used for devices with non-linear
		LED current scale.
- config : configuration for V4L2 Flash sub-device
	* dev_name - the name of the media entity, unique in the system,
	* flash_faults - bitmask of flash faults that the LED flash class
		device can report; corresponding LED_FAULT* bit definitions are
		available in <linux/led-class-flash.h>,
	* torch_intensity - constraints for the LED in TORCH mode
		in microamperes,
	* indicator_intensity - constraints for the indicator LED
		in microamperes,
	* has_external_strobe - determines whether the flash strobe source
		can be switched to external,

On remove the v4l2_flash_release function has to be called, which takes one
argument - struct v4l2_flash pointer returned previously by v4l2_flash_init.
This function can be safely called with NULL or error pointer argument.

Please refer to drivers/leds/leds-max77693.c for an exemplary usage of the
v4l2 flash wrapper.

Once the V4L2 sub-device is registered by the driver which created the Media
controller device, the sub-device node acts just as a node of a native V4L2
flash API device would. The calls are simply routed to the LED flash API.

Opening the V4L2 flash sub-device makes the LED subsystem sysfs interface
unavailable. The interface is re-enabled after the V4L2 flash sub-device
is closed.