/******************************************************************************
*
* Copyright(c) 2009-2014 Realtek Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* The full GNU General Public License is included in this distribution in the
* file called LICENSE.
*
* Contact Information:
* wlanfae <wlanfae@realtek.com>
* Realtek Corporation, No. 2, Innovation Road II, Hsinchu Science Park,
* Hsinchu 300, Taiwan.
*
* Larry Finger <Larry.Finger@lwfinger.net>
*
*****************************************************************************/
#ifndef __RTL8723BE_PWRSEQ_H__
#define __RTL8723BE_PWRSEQ_H__
#include "../pwrseqcmd.h"
/**
* Check document WM-20130425-JackieLau-RTL8723B_Power_Architecture v05.vsd
* There are 6 HW Power States:
* 0: POFF--Power Off
* 1: PDN--Power Down
* 2: CARDEMU--Card Emulation
* 3: ACT--Active Mode
* 4: LPS--Low Power State
* 5: SUS--Suspend
*
* The transision from different states are defined below
* TRANS_CARDEMU_TO_ACT
* TRANS_ACT_TO_CARDEMU
* TRANS_CARDEMU_TO_SUS
* TRANS_SUS_TO_CARDEMU
* TRANS_CARDEMU_TO_PDN
* TRANS_ACT_TO_LPS
* TRANS_LPS_TO_ACT
*
* TRANS_END
*/
#define RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS 23
#define RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS 15
#define RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS 15
#define RTL8723B_TRANS_SUS_TO_CARDEMU_STEPS 15
#define RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS 15
#define RTL8723B_TRANS_PDN_TO_CARDEMU_STEPS 15
#define RTL8723B_TRANS_ACT_TO_LPS_STEPS 15
#define RTL8723B_TRANS_LPS_TO_ACT_STEPS 15
#define RTL8723B_TRANS_END_STEPS 1
#define RTL8723B_TRANS_CARDEMU_TO_ACT \
/* format */ \
/* comments here */ \
/* {offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value}, */\
/*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \
{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, \
/*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \
{0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, \
/*Delay 1ms*/ \
{0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS}, \
/*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/ \
{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), 0}, \
/* disable SW LPS 0x04[10]=0 and WLSUS_EN 0x04[11]=0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)|BIT(2)), 0}, \
/* Disable USB suspend */ \
{0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0) , BIT(0)}, \
/* wait till 0x04[17] = 1 power ready*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)}, \
/* Enable USB suspend */ \
{0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0) , 0}, \
/* release WLON reset 0x04[16]=1*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, \
/* disable HWPDN 0x04[15]=0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0}, \
/* disable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0}, \
/* polling until return 0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0}, \
/* Enable WL control XTAL setting*/ \
{0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), BIT(6)}, \
/*Enable falling edge triggering interrupt*/ \
{0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
/*Enable GPIO9 interrupt mode*/ \
{0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
/*Enable GPIO9 input mode*/ \
{0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0}, \
/*Enable HSISR GPIO[C:0] interrupt*/ \
{0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, \
/*Enable HSISR GPIO9 interrupt*/ \
{0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
/*For GPIO9 internal pull high setting by test chip*/ \
{0x0068, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3), BIT(3)}, \
/*For GPIO9 internal pull high setting*/ \
{0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), BIT(6)},
#define RTL8723B_TRANS_ACT_TO_CARDEMU \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
/*0x1F[7:0] = 0 turn off RF*/ \
{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, \
/*0x4C[24] = 0x4F[0] = 0, */ \
/*switch DPDT_SEL_P output from register 0x65[2] */ \
{0x004F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, \
/*Enable rising edge triggering interrupt*/ \
{0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0}, \
/*0x04[9] = 1 turn off MAC by HW state machine*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
/*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, \
/* Enable BT control XTAL setting*/ \
{0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), 0}, \
/*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/ \
{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, \
PWR_CMD_WRITE, BIT(5), BIT(5)}, \
/*0x20[0] = 1b'0 disable LDOA12 MACRO block*/ \
{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, \
PWR_CMD_WRITE, BIT(0), 0},
#define RTL8723B_TRANS_CARDEMU_TO_SUS \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
/*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4) | BIT(3), (BIT(4) | BIT(3))}, \
/*0x04[12:11] = 2b'01 enable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, \
PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3)}, \
/*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
/*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, \
/*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3) | BIT(4)},\
/*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, \
/*wait power state to suspend*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0},
#define RTL8723B_TRANS_SUS_TO_CARDEMU \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
/*clear suspend enable and power down enable*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, \
/*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, \
/*wait power state to suspend*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, \
/*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, \
/*0x04[12:11] = 2b'01enable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0},
#define RTL8723B_TRANS_CARDEMU_TO_CARDDIS \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
/*0x07=0x20 , SOP option to disable BG/MB*/ \
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, \
/*0x04[12:11] = 2b'01 enable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, \
/*0x04[10] = 1, enable SW LPS*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), BIT(2)}, \
/*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \
{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 1}, \
/*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
/*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, \
/*wait power state to suspend*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0},
#define RTL8723B_TRANS_CARDDIS_TO_CARDEMU \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
/*clear suspend enable and power down enable*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, \
/*Set SDIO suspend local register*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, \
/*wait power state to suspend*/ \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, \
/*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \
{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, \
/*0x04[12:11] = 2b'01enable WL suspend*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, \
/*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, \
/*PCIe DMA start*/ \
{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},
#define RTL8723B_TRANS_CARDEMU_TO_PDN \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
/*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
/*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_SDIO_MSK | PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, \
PWR_CMD_WRITE, 0xFF, 0x20}, \
/* 0x04[16] = 0*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, \
/* 0x04[15] = 1*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)},
#define RTL8723B_TRANS_PDN_TO_CARDEMU \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
/* 0x04[15] = 0*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},
#define RTL8723B_TRANS_ACT_TO_LPS \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
/*PCIe DMA stop*/ \
{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, \
/*Tx Pause*/ \
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, \
/*Should be zero if no packet is transmitting*/ \
{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0}, \
/*Should be zero if no packet is transmitting*/ \
{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0}, \
/*Should be zero if no packet is transmitting*/ \
{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0}, \
/*Should be zero if no packet is transmitting*/ \
{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0}, \
/*CCK and OFDM are disabled,and clock are gated*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, \
/*Delay 1us*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US}, \
/*Whole BB is reset*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0}, \
/*Reset MAC TRX*/ \
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03}, \
/*check if removed later*/ \
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0}, \
/*When driver enter Sus/ Disable, enable LOP for BT*/ \
{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00}, \
/*Respond TxOK to scheduler*/ \
{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)},
#define RTL8723B_TRANS_LPS_TO_ACT \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
/*SDIO RPWM*/ \
{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, \
/*USB RPWM*/ \
{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, \
/*PCIe RPWM*/ \
{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, \
/*Delay*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, \
/*. 0x08[4] = 0 switch TSF to 40M*/ \
{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, \
/*Polling 0x109[7]=0 TSF in 40M*/ \
{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(7), 0}, \
/*. 0x29[7:6] = 2b'00 enable BB clock*/ \
{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6)|BIT(7), 0}, \
/*. 0x101[1] = 1*/ \
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
/*. 0x100[7:0] = 0xFF enable WMAC TRX*/ \
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, \
/*. 0x02[1:0] = 2b'11 enable BB macro*/ \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1) | BIT(0), BIT(1) | BIT(0)}, \
/*. 0x522 = 0*/ \
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},
#define RTL8723B_TRANS_END \
/* format */ \
/* comments here */ \
/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\
{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, \
PWR_CMD_END, 0, 0},
extern struct wlan_pwr_cfg rtl8723B_power_on_flow
[RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS +
RTL8723B_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723B_radio_off_flow
[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723B_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723B_card_disable_flow
[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8723B_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723B_card_enable_flow
[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8723B_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723B_suspend_flow
[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS +
RTL8723B_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723B_resume_flow
[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS +
RTL8723B_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723B_hwpdn_flow
[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8723B_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723B_enter_lps_flow
[RTL8723B_TRANS_ACT_TO_LPS_STEPS +
RTL8723B_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8723B_leave_lps_flow
[RTL8723B_TRANS_LPS_TO_ACT_STEPS +
RTL8723B_TRANS_END_STEPS];
/* RTL8723 Power Configuration CMDs for PCIe interface */
#define RTL8723_NIC_PWR_ON_FLOW rtl8723B_power_on_flow
#define RTL8723_NIC_RF_OFF_FLOW rtl8723B_radio_off_flow
#define RTL8723_NIC_DISABLE_FLOW rtl8723B_card_disable_flow
#define RTL8723_NIC_ENABLE_FLOW rtl8723B_card_enable_flow
#define RTL8723_NIC_SUSPEND_FLOW rtl8723B_suspend_flow
#define RTL8723_NIC_RESUME_FLOW rtl8723B_resume_flow
#define RTL8723_NIC_PDN_FLOW rtl8723B_hwpdn_flow
#define RTL8723_NIC_LPS_ENTER_FLOW rtl8723B_enter_lps_flow
#define RTL8723_NIC_LPS_LEAVE_FLOW rtl8723B_leave_lps_flow
#endif