Training courses

Kernel and Embedded Linux

Bootlin training courses

Embedded Linux, kernel,
Yocto Project, Buildroot, real-time,
graphics, boot time, debugging...

Bootlin logo

Elixir Cross Referencer

   1
   2
   3
   4
   5
   6
   7
   8
   9
  10
  11
  12
  13
  14
  15
  16
  17
  18
  19
  20
  21
  22
  23
  24
  25
  26
  27
  28
  29
  30
  31
  32
  33
  34
  35
  36
  37
  38
  39
  40
  41
  42
  43
  44
  45
  46
  47
  48
  49
  50
  51
  52
  53
  54
  55
  56
  57
  58
  59
  60
  61
  62
  63
  64
  65
  66
  67
  68
  69
  70
  71
  72
  73
  74
  75
  76
  77
  78
  79
  80
  81
  82
  83
  84
  85
  86
  87
  88
  89
  90
  91
  92
  93
  94
  95
  96
  97
  98
  99
 100
 101
 102
 103
 104
 105
 106
 107
 108
 109
 110
 111
 112
 113
 114
 115
 116
 117
 118
 119
 120
 121
 122
 123
 124
 125
 126
 127
 128
 129
 130
 131
 132
 133
 134
 135
 136
 137
 138
 139
 140
 141
 142
 143
 144
 145
 146
 147
 148
 149
 150
 151
 152
 153
 154
 155
 156
 157
 158
 159
 160
 161
 162
 163
 164
 165
 166
 167
 168
 169
 170
 171
 172
 173
 174
 175
 176
 177
 178
 179
 180
 181
 182
 183
 184
 185
 186
 187
 188
 189
 190
 191
 192
 193
 194
 195
 196
 197
 198
 199
 200
 201
 202
 203
 204
 205
 206
 207
 208
 209
 210
 211
 212
 213
 214
 215
 216
 217
 218
 219
 220
 221
 222
 223
 224
 225
 226
 227
 228
 229
 230
 231
 232
 233
 234
 235
 236
 237
 238
 239
 240
 241
 242
 243
 244
 245
 246
 247
 248
 249
 250
 251
 252
 253
 254
 255
 256
 257
 258
 259
 260
 261
 262
 263
 264
 265
 266
 267
 268
 269
 270
 271
 272
 273
 274
 275
 276
 277
 278
 279
 280
 281
 282
 283
 284
 285
 286
 287
 288
 289
 290
 291
 292
 293
 294
 295
 296
 297
 298
 299
 300
 301
 302
 303
 304
 305
 306
 307
 308
 309
 310
 311
 312
 313
 314
 315
 316
 317
 318
 319
 320
 321
 322
 323
 324
 325
 326
 327
 328
 329
 330
 331
 332
 333
 334
 335
 336
 337
 338
 339
 340
 341
 342
 343
 344
 345
 346
 347
 348
 349
 350
 351
 352
 353
 354
 355
 356
 357
 358
 359
 360
 361
 362
 363
 364
 365
 366
 367
 368
 369
 370
 371
 372
 373
 374
 375
 376
 377
 378
 379
 380
 381
 382
 383
 384
 385
 386
 387
 388
 389
 390
 391
 392
 393
 394
 395
 396
 397
 398
 399
 400
 401
 402
 403
 404
 405
 406
 407
 408
 409
 410
 411
 412
 413
 414
 415
 416
 417
 418
 419
 420
 421
 422
 423
 424
 425
 426
 427
 428
 429
 430
 431
 432
 433
 434
 435
 436
 437
 438
 439
 440
 441
 442
 443
 444
 445
 446
 447
 448
 449
 450
 451
 452
 453
 454
 455
 456
 457
 458
 459
 460
 461
 462
 463
 464
 465
 466
 467
 468
 469
 470
 471
 472
 473
 474
 475
 476
 477
 478
 479
 480
 481
 482
 483
 484
 485
 486
 487
 488
 489
 490
 491
 492
 493
 494
 495
 496
 497
 498
 499
 500
 501
 502
 503
 504
 505
 506
 507
 508
 509
 510
 511
 512
 513
 514
 515
 516
 517
 518
 519
 520
 521
 522
 523
 524
 525
 526
 527
 528
 529
 530
 531
 532
 533
 534
 535
 536
 537
 538
 539
 540
 541
 542
 543
 544
 545
 546
 547
 548
 549
 550
 551
 552
 553
 554
 555
 556
 557
 558
 559
 560
 561
 562
 563
 564
 565
 566
 567
 568
 569
 570
 571
 572
 573
 574
 575
 576
 577
 578
 579
 580
 581
 582
 583
 584
 585
 586
 587
 588
 589
 590
 591
 592
 593
 594
 595
 596
 597
 598
 599
 600
 601
 602
 603
 604
 605
 606
 607
 608
 609
 610
 611
 612
 613
 614
 615
 616
 617
 618
 619
 620
 621
 622
 623
 624
 625
 626
 627
 628
 629
 630
 631
 632
 633
 634
 635
 636
 637
 638
 639
 640
 641
 642
 643
 644
 645
 646
 647
 648
 649
 650
 651
 652
 653
 654
 655
 656
 657
 658
 659
 660
 661
 662
 663
 664
 665
 666
 667
 668
 669
 670
 671
 672
 673
 674
 675
 676
 677
 678
 679
 680
 681
 682
 683
 684
 685
 686
 687
 688
 689
 690
 691
 692
 693
 694
 695
 696
 697
 698
 699
 700
 701
 702
 703
 704
 705
 706
 707
 708
 709
 710
 711
 712
 713
 714
 715
 716
 717
 718
 719
 720
 721
 722
 723
 724
 725
 726
 727
 728
 729
 730
 731
 732
 733
 734
 735
 736
 737
 738
 739
 740
 741
 742
 743
 744
 745
 746
 747
 748
 749
 750
 751
 752
 753
 754
 755
 756
 757
 758
 759
 760
 761
 762
 763
 764
 765
 766
 767
 768
 769
 770
 771
 772
 773
 774
 775
 776
 777
 778
 779
 780
 781
 782
 783
 784
 785
 786
 787
 788
 789
 790
 791
 792
 793
 794
 795
 796
 797
 798
 799
 800
 801
 802
 803
 804
 805
 806
 807
 808
 809
 810
 811
 812
 813
 814
 815
 816
 817
 818
 819
 820
 821
 822
 823
 824
 825
 826
 827
 828
 829
 830
 831
 832
 833
 834
 835
 836
 837
 838
 839
 840
 841
 842
 843
 844
 845
 846
 847
 848
 849
 850
 851
 852
 853
 854
 855
 856
 857
 858
 859
 860
 861
 862
 863
 864
 865
 866
 867
 868
 869
 870
 871
 872
 873
 874
 875
 876
 877
 878
 879
 880
 881
 882
 883
 884
 885
 886
 887
 888
 889
 890
 891
 892
 893
 894
 895
 896
 897
 898
 899
 900
 901
 902
 903
 904
 905
 906
 907
 908
 909
 910
 911
 912
 913
 914
 915
 916
 917
 918
 919
 920
 921
 922
 923
 924
 925
 926
 927
 928
 929
 930
 931
 932
 933
 934
 935
 936
 937
 938
 939
 940
 941
 942
 943
 944
 945
 946
 947
 948
 949
 950
 951
 952
 953
 954
 955
 956
 957
 958
 959
 960
 961
 962
 963
 964
 965
 966
 967
 968
 969
 970
 971
 972
 973
 974
 975
 976
 977
 978
 979
 980
 981
 982
 983
 984
 985
 986
 987
 988
 989
 990
 991
 992
 993
 994
 995
 996
 997
 998
 999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
/*
 * Driver for the Cirrus Logic EP93xx DMA Controller
 *
 * Copyright (C) 2011 Mika Westerberg
 *
 * DMA M2P implementation is based on the original
 * arch/arm/mach-ep93xx/dma-m2p.c which has following copyrights:
 *
 *   Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
 *   Copyright (C) 2006 Applied Data Systems
 *   Copyright (C) 2009 Ryan Mallon <rmallon@gmail.com>
 *
 * This driver is based on dw_dmac and amba-pl08x drivers.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 */

#include <linux/clk.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/dmaengine.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>

#include <linux/platform_data/dma-ep93xx.h>

#include "dmaengine.h"

/* M2P registers */
#define M2P_CONTROL			0x0000
#define M2P_CONTROL_STALLINT		BIT(0)
#define M2P_CONTROL_NFBINT		BIT(1)
#define M2P_CONTROL_CH_ERROR_INT	BIT(3)
#define M2P_CONTROL_ENABLE		BIT(4)
#define M2P_CONTROL_ICE			BIT(6)

#define M2P_INTERRUPT			0x0004
#define M2P_INTERRUPT_STALL		BIT(0)
#define M2P_INTERRUPT_NFB		BIT(1)
#define M2P_INTERRUPT_ERROR		BIT(3)

#define M2P_PPALLOC			0x0008
#define M2P_STATUS			0x000c

#define M2P_MAXCNT0			0x0020
#define M2P_BASE0			0x0024
#define M2P_MAXCNT1			0x0030
#define M2P_BASE1			0x0034

#define M2P_STATE_IDLE			0
#define M2P_STATE_STALL			1
#define M2P_STATE_ON			2
#define M2P_STATE_NEXT			3

/* M2M registers */
#define M2M_CONTROL			0x0000
#define M2M_CONTROL_DONEINT		BIT(2)
#define M2M_CONTROL_ENABLE		BIT(3)
#define M2M_CONTROL_START		BIT(4)
#define M2M_CONTROL_DAH			BIT(11)
#define M2M_CONTROL_SAH			BIT(12)
#define M2M_CONTROL_PW_SHIFT		9
#define M2M_CONTROL_PW_8		(0 << M2M_CONTROL_PW_SHIFT)
#define M2M_CONTROL_PW_16		(1 << M2M_CONTROL_PW_SHIFT)
#define M2M_CONTROL_PW_32		(2 << M2M_CONTROL_PW_SHIFT)
#define M2M_CONTROL_PW_MASK		(3 << M2M_CONTROL_PW_SHIFT)
#define M2M_CONTROL_TM_SHIFT		13
#define M2M_CONTROL_TM_TX		(1 << M2M_CONTROL_TM_SHIFT)
#define M2M_CONTROL_TM_RX		(2 << M2M_CONTROL_TM_SHIFT)
#define M2M_CONTROL_NFBINT		BIT(21)
#define M2M_CONTROL_RSS_SHIFT		22
#define M2M_CONTROL_RSS_SSPRX		(1 << M2M_CONTROL_RSS_SHIFT)
#define M2M_CONTROL_RSS_SSPTX		(2 << M2M_CONTROL_RSS_SHIFT)
#define M2M_CONTROL_RSS_IDE		(3 << M2M_CONTROL_RSS_SHIFT)
#define M2M_CONTROL_NO_HDSK		BIT(24)
#define M2M_CONTROL_PWSC_SHIFT		25

#define M2M_INTERRUPT			0x0004
#define M2M_INTERRUPT_MASK		6

#define M2M_STATUS			0x000c
#define M2M_STATUS_CTL_SHIFT		1
#define M2M_STATUS_CTL_IDLE		(0 << M2M_STATUS_CTL_SHIFT)
#define M2M_STATUS_CTL_STALL		(1 << M2M_STATUS_CTL_SHIFT)
#define M2M_STATUS_CTL_MEMRD		(2 << M2M_STATUS_CTL_SHIFT)
#define M2M_STATUS_CTL_MEMWR		(3 << M2M_STATUS_CTL_SHIFT)
#define M2M_STATUS_CTL_BWCWAIT		(4 << M2M_STATUS_CTL_SHIFT)
#define M2M_STATUS_CTL_MASK		(7 << M2M_STATUS_CTL_SHIFT)
#define M2M_STATUS_BUF_SHIFT		4
#define M2M_STATUS_BUF_NO		(0 << M2M_STATUS_BUF_SHIFT)
#define M2M_STATUS_BUF_ON		(1 << M2M_STATUS_BUF_SHIFT)
#define M2M_STATUS_BUF_NEXT		(2 << M2M_STATUS_BUF_SHIFT)
#define M2M_STATUS_BUF_MASK		(3 << M2M_STATUS_BUF_SHIFT)
#define M2M_STATUS_DONE			BIT(6)

#define M2M_BCR0			0x0010
#define M2M_BCR1			0x0014
#define M2M_SAR_BASE0			0x0018
#define M2M_SAR_BASE1			0x001c
#define M2M_DAR_BASE0			0x002c
#define M2M_DAR_BASE1			0x0030

#define DMA_MAX_CHAN_BYTES		0xffff
#define DMA_MAX_CHAN_DESCRIPTORS	32

struct ep93xx_dma_engine;

/**
 * struct ep93xx_dma_desc - EP93xx specific transaction descriptor
 * @src_addr: source address of the transaction
 * @dst_addr: destination address of the transaction
 * @size: size of the transaction (in bytes)
 * @complete: this descriptor is completed
 * @txd: dmaengine API descriptor
 * @tx_list: list of linked descriptors
 * @node: link used for putting this into a channel queue
 */
struct ep93xx_dma_desc {
	u32				src_addr;
	u32				dst_addr;
	size_t				size;
	bool				complete;
	struct dma_async_tx_descriptor	txd;
	struct list_head		tx_list;
	struct list_head		node;
};

/**
 * struct ep93xx_dma_chan - an EP93xx DMA M2P/M2M channel
 * @chan: dmaengine API channel
 * @edma: pointer to to the engine device
 * @regs: memory mapped registers
 * @irq: interrupt number of the channel
 * @clk: clock used by this channel
 * @tasklet: channel specific tasklet used for callbacks
 * @lock: lock protecting the fields following
 * @flags: flags for the channel
 * @buffer: which buffer to use next (0/1)
 * @active: flattened chain of descriptors currently being processed
 * @queue: pending descriptors which are handled next
 * @free_list: list of free descriptors which can be used
 * @runtime_addr: physical address currently used as dest/src (M2M only). This
 *                is set via .device_config before slave operation is
 *                prepared
 * @runtime_ctrl: M2M runtime values for the control register.
 *
 * As EP93xx DMA controller doesn't support real chained DMA descriptors we
 * will have slightly different scheme here: @active points to a head of
 * flattened DMA descriptor chain.
 *
 * @queue holds pending transactions. These are linked through the first
 * descriptor in the chain. When a descriptor is moved to the @active queue,
 * the first and chained descriptors are flattened into a single list.
 *
 * @chan.private holds pointer to &struct ep93xx_dma_data which contains
 * necessary channel configuration information. For memcpy channels this must
 * be %NULL.
 */
struct ep93xx_dma_chan {
	struct dma_chan			chan;
	const struct ep93xx_dma_engine	*edma;
	void __iomem			*regs;
	int				irq;
	struct clk			*clk;
	struct tasklet_struct		tasklet;
	/* protects the fields following */
	spinlock_t			lock;
	unsigned long			flags;
/* Channel is configured for cyclic transfers */
#define EP93XX_DMA_IS_CYCLIC		0

	int				buffer;
	struct list_head		active;
	struct list_head		queue;
	struct list_head		free_list;
	u32				runtime_addr;
	u32				runtime_ctrl;
};

/**
 * struct ep93xx_dma_engine - the EP93xx DMA engine instance
 * @dma_dev: holds the dmaengine device
 * @m2m: is this an M2M or M2P device
 * @hw_setup: method which sets the channel up for operation
 * @hw_shutdown: shuts the channel down and flushes whatever is left
 * @hw_submit: pushes active descriptor(s) to the hardware
 * @hw_interrupt: handle the interrupt
 * @num_channels: number of channels for this instance
 * @channels: array of channels
 *
 * There is one instance of this struct for the M2P channels and one for the
 * M2M channels. hw_xxx() methods are used to perform operations which are
 * different on M2M and M2P channels. These methods are called with channel
 * lock held and interrupts disabled so they cannot sleep.
 */
struct ep93xx_dma_engine {
	struct dma_device	dma_dev;
	bool			m2m;
	int			(*hw_setup)(struct ep93xx_dma_chan *);
	void			(*hw_shutdown)(struct ep93xx_dma_chan *);
	void			(*hw_submit)(struct ep93xx_dma_chan *);
	int			(*hw_interrupt)(struct ep93xx_dma_chan *);
#define INTERRUPT_UNKNOWN	0
#define INTERRUPT_DONE		1
#define INTERRUPT_NEXT_BUFFER	2

	size_t			num_channels;
	struct ep93xx_dma_chan	channels[];
};

static inline struct device *chan2dev(struct ep93xx_dma_chan *edmac)
{
	return &edmac->chan.dev->device;
}

static struct ep93xx_dma_chan *to_ep93xx_dma_chan(struct dma_chan *chan)
{
	return container_of(chan, struct ep93xx_dma_chan, chan);
}

/**
 * ep93xx_dma_set_active - set new active descriptor chain
 * @edmac: channel
 * @desc: head of the new active descriptor chain
 *
 * Sets @desc to be the head of the new active descriptor chain. This is the
 * chain which is processed next. The active list must be empty before calling
 * this function.
 *
 * Called with @edmac->lock held and interrupts disabled.
 */
static void ep93xx_dma_set_active(struct ep93xx_dma_chan *edmac,
				  struct ep93xx_dma_desc *desc)
{
	BUG_ON(!list_empty(&edmac->active));

	list_add_tail(&desc->node, &edmac->active);

	/* Flatten the @desc->tx_list chain into @edmac->active list */
	while (!list_empty(&desc->tx_list)) {
		struct ep93xx_dma_desc *d = list_first_entry(&desc->tx_list,
			struct ep93xx_dma_desc, node);

		/*
		 * We copy the callback parameters from the first descriptor
		 * to all the chained descriptors. This way we can call the
		 * callback without having to find out the first descriptor in
		 * the chain. Useful for cyclic transfers.
		 */
		d->txd.callback = desc->txd.callback;
		d->txd.callback_param = desc->txd.callback_param;

		list_move_tail(&d->node, &edmac->active);
	}
}

/* Called with @edmac->lock held and interrupts disabled */
static struct ep93xx_dma_desc *
ep93xx_dma_get_active(struct ep93xx_dma_chan *edmac)
{
	return list_first_entry_or_null(&edmac->active,
					struct ep93xx_dma_desc, node);
}

/**
 * ep93xx_dma_advance_active - advances to the next active descriptor
 * @edmac: channel
 *
 * Function advances active descriptor to the next in the @edmac->active and
 * returns %true if we still have descriptors in the chain to process.
 * Otherwise returns %false.
 *
 * When the channel is in cyclic mode always returns %true.
 *
 * Called with @edmac->lock held and interrupts disabled.
 */
static bool ep93xx_dma_advance_active(struct ep93xx_dma_chan *edmac)
{
	struct ep93xx_dma_desc *desc;

	list_rotate_left(&edmac->active);

	if (test_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags))
		return true;

	desc = ep93xx_dma_get_active(edmac);
	if (!desc)
		return false;

	/*
	 * If txd.cookie is set it means that we are back in the first
	 * descriptor in the chain and hence done with it.
	 */
	return !desc->txd.cookie;
}

/*
 * M2P DMA implementation
 */

static void m2p_set_control(struct ep93xx_dma_chan *edmac, u32 control)
{
	writel(control, edmac->regs + M2P_CONTROL);
	/*
	 * EP93xx User's Guide states that we must perform a dummy read after
	 * write to the control register.
	 */
	readl(edmac->regs + M2P_CONTROL);
}

static int m2p_hw_setup(struct ep93xx_dma_chan *edmac)
{
	struct ep93xx_dma_data *data = edmac->chan.private;
	u32 control;

	writel(data->port & 0xf, edmac->regs + M2P_PPALLOC);

	control = M2P_CONTROL_CH_ERROR_INT | M2P_CONTROL_ICE
		| M2P_CONTROL_ENABLE;
	m2p_set_control(edmac, control);

	return 0;
}

static inline u32 m2p_channel_state(struct ep93xx_dma_chan *edmac)
{
	return (readl(edmac->regs + M2P_STATUS) >> 4) & 0x3;
}

static void m2p_hw_shutdown(struct ep93xx_dma_chan *edmac)
{
	u32 control;

	control = readl(edmac->regs + M2P_CONTROL);
	control &= ~(M2P_CONTROL_STALLINT | M2P_CONTROL_NFBINT);
	m2p_set_control(edmac, control);

	while (m2p_channel_state(edmac) >= M2P_STATE_ON)
		cpu_relax();

	m2p_set_control(edmac, 0);

	while (m2p_channel_state(edmac) == M2P_STATE_STALL)
		cpu_relax();
}

static void m2p_fill_desc(struct ep93xx_dma_chan *edmac)
{
	struct ep93xx_dma_desc *desc;
	u32 bus_addr;

	desc = ep93xx_dma_get_active(edmac);
	if (!desc) {
		dev_warn(chan2dev(edmac), "M2P: empty descriptor list\n");
		return;
	}

	if (ep93xx_dma_chan_direction(&edmac->chan) == DMA_MEM_TO_DEV)
		bus_addr = desc->src_addr;
	else
		bus_addr = desc->dst_addr;

	if (edmac->buffer == 0) {
		writel(desc->size, edmac->regs + M2P_MAXCNT0);
		writel(bus_addr, edmac->regs + M2P_BASE0);
	} else {
		writel(desc->size, edmac->regs + M2P_MAXCNT1);
		writel(bus_addr, edmac->regs + M2P_BASE1);
	}

	edmac->buffer ^= 1;
}

static void m2p_hw_submit(struct ep93xx_dma_chan *edmac)
{
	u32 control = readl(edmac->regs + M2P_CONTROL);

	m2p_fill_desc(edmac);
	control |= M2P_CONTROL_STALLINT;

	if (ep93xx_dma_advance_active(edmac)) {
		m2p_fill_desc(edmac);
		control |= M2P_CONTROL_NFBINT;
	}

	m2p_set_control(edmac, control);
}

static int m2p_hw_interrupt(struct ep93xx_dma_chan *edmac)
{
	u32 irq_status = readl(edmac->regs + M2P_INTERRUPT);
	u32 control;

	if (irq_status & M2P_INTERRUPT_ERROR) {
		struct ep93xx_dma_desc *desc = ep93xx_dma_get_active(edmac);

		/* Clear the error interrupt */
		writel(1, edmac->regs + M2P_INTERRUPT);

		/*
		 * It seems that there is no easy way of reporting errors back
		 * to client so we just report the error here and continue as
		 * usual.
		 *
		 * Revisit this when there is a mechanism to report back the
		 * errors.
		 */
		dev_err(chan2dev(edmac),
			"DMA transfer failed! Details:\n"
			"\tcookie	: %d\n"
			"\tsrc_addr	: 0x%08x\n"
			"\tdst_addr	: 0x%08x\n"
			"\tsize		: %zu\n",
			desc->txd.cookie, desc->src_addr, desc->dst_addr,
			desc->size);
	}

	/*
	 * Even latest E2 silicon revision sometimes assert STALL interrupt
	 * instead of NFB. Therefore we treat them equally, basing on the
	 * amount of data we still have to transfer.
	 */
	if (!(irq_status & (M2P_INTERRUPT_STALL | M2P_INTERRUPT_NFB)))
		return INTERRUPT_UNKNOWN;

	if (ep93xx_dma_advance_active(edmac)) {
		m2p_fill_desc(edmac);
		return INTERRUPT_NEXT_BUFFER;
	}

	/* Disable interrupts */
	control = readl(edmac->regs + M2P_CONTROL);
	control &= ~(M2P_CONTROL_STALLINT | M2P_CONTROL_NFBINT);
	m2p_set_control(edmac, control);

	return INTERRUPT_DONE;
}

/*
 * M2M DMA implementation
 */

static int m2m_hw_setup(struct ep93xx_dma_chan *edmac)
{
	const struct ep93xx_dma_data *data = edmac->chan.private;
	u32 control = 0;

	if (!data) {
		/* This is memcpy channel, nothing to configure */
		writel(control, edmac->regs + M2M_CONTROL);
		return 0;
	}

	switch (data->port) {
	case EP93XX_DMA_SSP:
		/*
		 * This was found via experimenting - anything less than 5
		 * causes the channel to perform only a partial transfer which
		 * leads to problems since we don't get DONE interrupt then.
		 */
		control = (5 << M2M_CONTROL_PWSC_SHIFT);
		control |= M2M_CONTROL_NO_HDSK;

		if (data->direction == DMA_MEM_TO_DEV) {
			control |= M2M_CONTROL_DAH;
			control |= M2M_CONTROL_TM_TX;
			control |= M2M_CONTROL_RSS_SSPTX;
		} else {
			control |= M2M_CONTROL_SAH;
			control |= M2M_CONTROL_TM_RX;
			control |= M2M_CONTROL_RSS_SSPRX;
		}
		break;

	case EP93XX_DMA_IDE:
		/*
		 * This IDE part is totally untested. Values below are taken
		 * from the EP93xx Users's Guide and might not be correct.
		 */
		if (data->direction == DMA_MEM_TO_DEV) {
			/* Worst case from the UG */
			control = (3 << M2M_CONTROL_PWSC_SHIFT);
			control |= M2M_CONTROL_DAH;
			control |= M2M_CONTROL_TM_TX;
		} else {
			control = (2 << M2M_CONTROL_PWSC_SHIFT);
			control |= M2M_CONTROL_SAH;
			control |= M2M_CONTROL_TM_RX;
		}

		control |= M2M_CONTROL_NO_HDSK;
		control |= M2M_CONTROL_RSS_IDE;
		control |= M2M_CONTROL_PW_16;
		break;

	default:
		return -EINVAL;
	}

	writel(control, edmac->regs + M2M_CONTROL);
	return 0;
}

static void m2m_hw_shutdown(struct ep93xx_dma_chan *edmac)
{
	/* Just disable the channel */
	writel(0, edmac->regs + M2M_CONTROL);
}

static void m2m_fill_desc(struct ep93xx_dma_chan *edmac)
{
	struct ep93xx_dma_desc *desc;

	desc = ep93xx_dma_get_active(edmac);
	if (!desc) {
		dev_warn(chan2dev(edmac), "M2M: empty descriptor list\n");
		return;
	}

	if (edmac->buffer == 0) {
		writel(desc->src_addr, edmac->regs + M2M_SAR_BASE0);
		writel(desc->dst_addr, edmac->regs + M2M_DAR_BASE0);
		writel(desc->size, edmac->regs + M2M_BCR0);
	} else {
		writel(desc->src_addr, edmac->regs + M2M_SAR_BASE1);
		writel(desc->dst_addr, edmac->regs + M2M_DAR_BASE1);
		writel(desc->size, edmac->regs + M2M_BCR1);
	}

	edmac->buffer ^= 1;
}

static void m2m_hw_submit(struct ep93xx_dma_chan *edmac)
{
	struct ep93xx_dma_data *data = edmac->chan.private;
	u32 control = readl(edmac->regs + M2M_CONTROL);

	/*
	 * Since we allow clients to configure PW (peripheral width) we always
	 * clear PW bits here and then set them according what is given in
	 * the runtime configuration.
	 */
	control &= ~M2M_CONTROL_PW_MASK;
	control |= edmac->runtime_ctrl;

	m2m_fill_desc(edmac);
	control |= M2M_CONTROL_DONEINT;

	if (ep93xx_dma_advance_active(edmac)) {
		m2m_fill_desc(edmac);
		control |= M2M_CONTROL_NFBINT;
	}

	/*
	 * Now we can finally enable the channel. For M2M channel this must be
	 * done _after_ the BCRx registers are programmed.
	 */
	control |= M2M_CONTROL_ENABLE;
	writel(control, edmac->regs + M2M_CONTROL);

	if (!data) {
		/*
		 * For memcpy channels the software trigger must be asserted
		 * in order to start the memcpy operation.
		 */
		control |= M2M_CONTROL_START;
		writel(control, edmac->regs + M2M_CONTROL);
	}
}

/*
 * According to EP93xx User's Guide, we should receive DONE interrupt when all
 * M2M DMA controller transactions complete normally. This is not always the
 * case - sometimes EP93xx M2M DMA asserts DONE interrupt when the DMA channel
 * is still running (channel Buffer FSM in DMA_BUF_ON state, and channel
 * Control FSM in DMA_MEM_RD state, observed at least in IDE-DMA operation).
 * In effect, disabling the channel when only DONE bit is set could stop
 * currently running DMA transfer. To avoid this, we use Buffer FSM and
 * Control FSM to check current state of DMA channel.
 */
static int m2m_hw_interrupt(struct ep93xx_dma_chan *edmac)
{
	u32 status = readl(edmac->regs + M2M_STATUS);
	u32 ctl_fsm = status & M2M_STATUS_CTL_MASK;
	u32 buf_fsm = status & M2M_STATUS_BUF_MASK;
	bool done = status & M2M_STATUS_DONE;
	bool last_done;
	u32 control;
	struct ep93xx_dma_desc *desc;

	/* Accept only DONE and NFB interrupts */
	if (!(readl(edmac->regs + M2M_INTERRUPT) & M2M_INTERRUPT_MASK))
		return INTERRUPT_UNKNOWN;

	if (done) {
		/* Clear the DONE bit */
		writel(0, edmac->regs + M2M_INTERRUPT);
	}

	/*
	 * Check whether we are done with descriptors or not. This, together
	 * with DMA channel state, determines action to take in interrupt.
	 */
	desc = ep93xx_dma_get_active(edmac);
	last_done = !desc || desc->txd.cookie;

	/*
	 * Use M2M DMA Buffer FSM and Control FSM to check current state of
	 * DMA channel. Using DONE and NFB bits from channel status register
	 * or bits from channel interrupt register is not reliable.
	 */
	if (!last_done &&
	    (buf_fsm == M2M_STATUS_BUF_NO ||
	     buf_fsm == M2M_STATUS_BUF_ON)) {
		/*
		 * Two buffers are ready for update when Buffer FSM is in
		 * DMA_NO_BUF state. Only one buffer can be prepared without
		 * disabling the channel or polling the DONE bit.
		 * To simplify things, always prepare only one buffer.
		 */
		if (ep93xx_dma_advance_active(edmac)) {
			m2m_fill_desc(edmac);
			if (done && !edmac->chan.private) {
				/* Software trigger for memcpy channel */
				control = readl(edmac->regs + M2M_CONTROL);
				control |= M2M_CONTROL_START;
				writel(control, edmac->regs + M2M_CONTROL);
			}
			return INTERRUPT_NEXT_BUFFER;
		} else {
			last_done = true;
		}
	}

	/*
	 * Disable the channel only when Buffer FSM is in DMA_NO_BUF state
	 * and Control FSM is in DMA_STALL state.
	 */
	if (last_done &&
	    buf_fsm == M2M_STATUS_BUF_NO &&
	    ctl_fsm == M2M_STATUS_CTL_STALL) {
		/* Disable interrupts and the channel */
		control = readl(edmac->regs + M2M_CONTROL);
		control &= ~(M2M_CONTROL_DONEINT | M2M_CONTROL_NFBINT
			    | M2M_CONTROL_ENABLE);
		writel(control, edmac->regs + M2M_CONTROL);
		return INTERRUPT_DONE;
	}

	/*
	 * Nothing to do this time.
	 */
	return INTERRUPT_NEXT_BUFFER;
}

/*
 * DMA engine API implementation
 */

static struct ep93xx_dma_desc *
ep93xx_dma_desc_get(struct ep93xx_dma_chan *edmac)
{
	struct ep93xx_dma_desc *desc, *_desc;
	struct ep93xx_dma_desc *ret = NULL;
	unsigned long flags;

	spin_lock_irqsave(&edmac->lock, flags);
	list_for_each_entry_safe(desc, _desc, &edmac->free_list, node) {
		if (async_tx_test_ack(&desc->txd)) {
			list_del_init(&desc->node);

			/* Re-initialize the descriptor */
			desc->src_addr = 0;
			desc->dst_addr = 0;
			desc->size = 0;
			desc->complete = false;
			desc->txd.cookie = 0;
			desc->txd.callback = NULL;
			desc->txd.callback_param = NULL;

			ret = desc;
			break;
		}
	}
	spin_unlock_irqrestore(&edmac->lock, flags);
	return ret;
}

static void ep93xx_dma_desc_put(struct ep93xx_dma_chan *edmac,
				struct ep93xx_dma_desc *desc)
{
	if (desc) {
		unsigned long flags;

		spin_lock_irqsave(&edmac->lock, flags);
		list_splice_init(&desc->tx_list, &edmac->free_list);
		list_add(&desc->node, &edmac->free_list);
		spin_unlock_irqrestore(&edmac->lock, flags);
	}
}

/**
 * ep93xx_dma_advance_work - start processing the next pending transaction
 * @edmac: channel
 *
 * If we have pending transactions queued and we are currently idling, this
 * function takes the next queued transaction from the @edmac->queue and
 * pushes it to the hardware for execution.
 */
static void ep93xx_dma_advance_work(struct ep93xx_dma_chan *edmac)
{
	struct ep93xx_dma_desc *new;
	unsigned long flags;

	spin_lock_irqsave(&edmac->lock, flags);
	if (!list_empty(&edmac->active) || list_empty(&edmac->queue)) {
		spin_unlock_irqrestore(&edmac->lock, flags);
		return;
	}

	/* Take the next descriptor from the pending queue */
	new = list_first_entry(&edmac->queue, struct ep93xx_dma_desc, node);
	list_del_init(&new->node);

	ep93xx_dma_set_active(edmac, new);

	/* Push it to the hardware */
	edmac->edma->hw_submit(edmac);
	spin_unlock_irqrestore(&edmac->lock, flags);
}

static void ep93xx_dma_tasklet(unsigned long data)
{
	struct ep93xx_dma_chan *edmac = (struct ep93xx_dma_chan *)data;
	struct ep93xx_dma_desc *desc, *d;
	struct dmaengine_desc_callback cb;
	LIST_HEAD(list);

	memset(&cb, 0, sizeof(cb));
	spin_lock_irq(&edmac->lock);
	/*
	 * If dma_terminate_all() was called before we get to run, the active
	 * list has become empty. If that happens we aren't supposed to do
	 * anything more than call ep93xx_dma_advance_work().
	 */
	desc = ep93xx_dma_get_active(edmac);
	if (desc) {
		if (desc->complete) {
			/* mark descriptor complete for non cyclic case only */
			if (!test_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags))
				dma_cookie_complete(&desc->txd);
			list_splice_init(&edmac->active, &list);
		}
		dmaengine_desc_get_callback(&desc->txd, &cb);
	}
	spin_unlock_irq(&edmac->lock);

	/* Pick up the next descriptor from the queue */
	ep93xx_dma_advance_work(edmac);

	/* Now we can release all the chained descriptors */
	list_for_each_entry_safe(desc, d, &list, node) {
		dma_descriptor_unmap(&desc->txd);
		ep93xx_dma_desc_put(edmac, desc);
	}

	dmaengine_desc_callback_invoke(&cb, NULL);
}

static irqreturn_t ep93xx_dma_interrupt(int irq, void *dev_id)
{
	struct ep93xx_dma_chan *edmac = dev_id;
	struct ep93xx_dma_desc *desc;
	irqreturn_t ret = IRQ_HANDLED;

	spin_lock(&edmac->lock);

	desc = ep93xx_dma_get_active(edmac);
	if (!desc) {
		dev_warn(chan2dev(edmac),
			 "got interrupt while active list is empty\n");
		spin_unlock(&edmac->lock);
		return IRQ_NONE;
	}

	switch (edmac->edma->hw_interrupt(edmac)) {
	case INTERRUPT_DONE:
		desc->complete = true;
		tasklet_schedule(&edmac->tasklet);
		break;

	case INTERRUPT_NEXT_BUFFER:
		if (test_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags))
			tasklet_schedule(&edmac->tasklet);
		break;

	default:
		dev_warn(chan2dev(edmac), "unknown interrupt!\n");
		ret = IRQ_NONE;
		break;
	}

	spin_unlock(&edmac->lock);
	return ret;
}

/**
 * ep93xx_dma_tx_submit - set the prepared descriptor(s) to be executed
 * @tx: descriptor to be executed
 *
 * Function will execute given descriptor on the hardware or if the hardware
 * is busy, queue the descriptor to be executed later on. Returns cookie which
 * can be used to poll the status of the descriptor.
 */
static dma_cookie_t ep93xx_dma_tx_submit(struct dma_async_tx_descriptor *tx)
{
	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(tx->chan);
	struct ep93xx_dma_desc *desc;
	dma_cookie_t cookie;
	unsigned long flags;

	spin_lock_irqsave(&edmac->lock, flags);
	cookie = dma_cookie_assign(tx);

	desc = container_of(tx, struct ep93xx_dma_desc, txd);

	/*
	 * If nothing is currently prosessed, we push this descriptor
	 * directly to the hardware. Otherwise we put the descriptor
	 * to the pending queue.
	 */
	if (list_empty(&edmac->active)) {
		ep93xx_dma_set_active(edmac, desc);
		edmac->edma->hw_submit(edmac);
	} else {
		list_add_tail(&desc->node, &edmac->queue);
	}

	spin_unlock_irqrestore(&edmac->lock, flags);
	return cookie;
}

/**
 * ep93xx_dma_alloc_chan_resources - allocate resources for the channel
 * @chan: channel to allocate resources
 *
 * Function allocates necessary resources for the given DMA channel and
 * returns number of allocated descriptors for the channel. Negative errno
 * is returned in case of failure.
 */
static int ep93xx_dma_alloc_chan_resources(struct dma_chan *chan)
{
	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
	struct ep93xx_dma_data *data = chan->private;
	const char *name = dma_chan_name(chan);
	int ret, i;

	/* Sanity check the channel parameters */
	if (!edmac->edma->m2m) {
		if (!data)
			return -EINVAL;
		if (data->port < EP93XX_DMA_I2S1 ||
		    data->port > EP93XX_DMA_IRDA)
			return -EINVAL;
		if (data->direction != ep93xx_dma_chan_direction(chan))
			return -EINVAL;
	} else {
		if (data) {
			switch (data->port) {
			case EP93XX_DMA_SSP:
			case EP93XX_DMA_IDE:
				if (!is_slave_direction(data->direction))
					return -EINVAL;
				break;
			default:
				return -EINVAL;
			}
		}
	}

	if (data && data->name)
		name = data->name;

	ret = clk_enable(edmac->clk);
	if (ret)
		return ret;

	ret = request_irq(edmac->irq, ep93xx_dma_interrupt, 0, name, edmac);
	if (ret)
		goto fail_clk_disable;

	spin_lock_irq(&edmac->lock);
	dma_cookie_init(&edmac->chan);
	ret = edmac->edma->hw_setup(edmac);
	spin_unlock_irq(&edmac->lock);

	if (ret)
		goto fail_free_irq;

	for (i = 0; i < DMA_MAX_CHAN_DESCRIPTORS; i++) {
		struct ep93xx_dma_desc *desc;

		desc = kzalloc(sizeof(*desc), GFP_KERNEL);
		if (!desc) {
			dev_warn(chan2dev(edmac), "not enough descriptors\n");
			break;
		}

		INIT_LIST_HEAD(&desc->tx_list);

		dma_async_tx_descriptor_init(&desc->txd, chan);
		desc->txd.flags = DMA_CTRL_ACK;
		desc->txd.tx_submit = ep93xx_dma_tx_submit;

		ep93xx_dma_desc_put(edmac, desc);
	}

	return i;

fail_free_irq:
	free_irq(edmac->irq, edmac);
fail_clk_disable:
	clk_disable(edmac->clk);

	return ret;
}

/**
 * ep93xx_dma_free_chan_resources - release resources for the channel
 * @chan: channel
 *
 * Function releases all the resources allocated for the given channel.
 * The channel must be idle when this is called.
 */
static void ep93xx_dma_free_chan_resources(struct dma_chan *chan)
{
	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
	struct ep93xx_dma_desc *desc, *d;
	unsigned long flags;
	LIST_HEAD(list);

	BUG_ON(!list_empty(&edmac->active));
	BUG_ON(!list_empty(&edmac->queue));

	spin_lock_irqsave(&edmac->lock, flags);
	edmac->edma->hw_shutdown(edmac);
	edmac->runtime_addr = 0;
	edmac->runtime_ctrl = 0;
	edmac->buffer = 0;
	list_splice_init(&edmac->free_list, &list);
	spin_unlock_irqrestore(&edmac->lock, flags);

	list_for_each_entry_safe(desc, d, &list, node)
		kfree(desc);

	clk_disable(edmac->clk);
	free_irq(edmac->irq, edmac);
}

/**
 * ep93xx_dma_prep_dma_memcpy - prepare a memcpy DMA operation
 * @chan: channel
 * @dest: destination bus address
 * @src: source bus address
 * @len: size of the transaction
 * @flags: flags for the descriptor
 *
 * Returns a valid DMA descriptor or %NULL in case of failure.
 */
static struct dma_async_tx_descriptor *
ep93xx_dma_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest,
			   dma_addr_t src, size_t len, unsigned long flags)
{
	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
	struct ep93xx_dma_desc *desc, *first;
	size_t bytes, offset;

	first = NULL;
	for (offset = 0; offset < len; offset += bytes) {
		desc = ep93xx_dma_desc_get(edmac);
		if (!desc) {
			dev_warn(chan2dev(edmac), "couln't get descriptor\n");
			goto fail;
		}

		bytes = min_t(size_t, len - offset, DMA_MAX_CHAN_BYTES);

		desc->src_addr = src + offset;
		desc->dst_addr = dest + offset;
		desc->size = bytes;

		if (!first)
			first = desc;
		else
			list_add_tail(&desc->node, &first->tx_list);
	}

	first->txd.cookie = -EBUSY;
	first->txd.flags = flags;

	return &first->txd;
fail:
	ep93xx_dma_desc_put(edmac, first);
	return NULL;
}

/**
 * ep93xx_dma_prep_slave_sg - prepare a slave DMA operation
 * @chan: channel
 * @sgl: list of buffers to transfer
 * @sg_len: number of entries in @sgl
 * @dir: direction of tha DMA transfer
 * @flags: flags for the descriptor
 * @context: operation context (ignored)
 *
 * Returns a valid DMA descriptor or %NULL in case of failure.
 */
static struct dma_async_tx_descriptor *
ep93xx_dma_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl,
			 unsigned int sg_len, enum dma_transfer_direction dir,
			 unsigned long flags, void *context)
{
	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
	struct ep93xx_dma_desc *desc, *first;
	struct scatterlist *sg;
	int i;

	if (!edmac->edma->m2m && dir != ep93xx_dma_chan_direction(chan)) {
		dev_warn(chan2dev(edmac),
			 "channel was configured with different direction\n");
		return NULL;
	}

	if (test_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags)) {
		dev_warn(chan2dev(edmac),
			 "channel is already used for cyclic transfers\n");
		return NULL;
	}

	first = NULL;
	for_each_sg(sgl, sg, sg_len, i) {
		size_t len = sg_dma_len(sg);

		if (len > DMA_MAX_CHAN_BYTES) {
			dev_warn(chan2dev(edmac), "too big transfer size %zu\n",
				 len);
			goto fail;
		}

		desc = ep93xx_dma_desc_get(edmac);
		if (!desc) {
			dev_warn(chan2dev(edmac), "couln't get descriptor\n");
			goto fail;
		}

		if (dir == DMA_MEM_TO_DEV) {
			desc->src_addr = sg_dma_address(sg);
			desc->dst_addr = edmac->runtime_addr;
		} else {
			desc->src_addr = edmac->runtime_addr;
			desc->dst_addr = sg_dma_address(sg);
		}
		desc->size = len;

		if (!first)
			first = desc;
		else
			list_add_tail(&desc->node, &first->tx_list);
	}

	first->txd.cookie = -EBUSY;
	first->txd.flags = flags;

	return &first->txd;

fail:
	ep93xx_dma_desc_put(edmac, first);
	return NULL;
}

/**
 * ep93xx_dma_prep_dma_cyclic - prepare a cyclic DMA operation
 * @chan: channel
 * @dma_addr: DMA mapped address of the buffer
 * @buf_len: length of the buffer (in bytes)
 * @period_len: length of a single period
 * @dir: direction of the operation
 * @flags: tx descriptor status flags
 *
 * Prepares a descriptor for cyclic DMA operation. This means that once the
 * descriptor is submitted, we will be submitting in a @period_len sized
 * buffers and calling callback once the period has been elapsed. Transfer
 * terminates only when client calls dmaengine_terminate_all() for this
 * channel.
 *
 * Returns a valid DMA descriptor or %NULL in case of failure.
 */
static struct dma_async_tx_descriptor *
ep93xx_dma_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr,
			   size_t buf_len, size_t period_len,
			   enum dma_transfer_direction dir, unsigned long flags)
{
	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
	struct ep93xx_dma_desc *desc, *first;
	size_t offset = 0;

	if (!edmac->edma->m2m && dir != ep93xx_dma_chan_direction(chan)) {
		dev_warn(chan2dev(edmac),
			 "channel was configured with different direction\n");
		return NULL;
	}

	if (test_and_set_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags)) {
		dev_warn(chan2dev(edmac),
			 "channel is already used for cyclic transfers\n");
		return NULL;
	}

	if (period_len > DMA_MAX_CHAN_BYTES) {
		dev_warn(chan2dev(edmac), "too big period length %zu\n",
			 period_len);
		return NULL;
	}

	/* Split the buffer into period size chunks */
	first = NULL;
	for (offset = 0; offset < buf_len; offset += period_len) {
		desc = ep93xx_dma_desc_get(edmac);
		if (!desc) {
			dev_warn(chan2dev(edmac), "couln't get descriptor\n");
			goto fail;
		}

		if (dir == DMA_MEM_TO_DEV) {
			desc->src_addr = dma_addr + offset;
			desc->dst_addr = edmac->runtime_addr;
		} else {
			desc->src_addr = edmac->runtime_addr;
			desc->dst_addr = dma_addr + offset;
		}

		desc->size = period_len;

		if (!first)
			first = desc;
		else
			list_add_tail(&desc->node, &first->tx_list);
	}

	first->txd.cookie = -EBUSY;

	return &first->txd;

fail:
	ep93xx_dma_desc_put(edmac, first);
	return NULL;
}

/**
 * ep93xx_dma_terminate_all - terminate all transactions
 * @chan: channel
 *
 * Stops all DMA transactions. All descriptors are put back to the
 * @edmac->free_list and callbacks are _not_ called.
 */
static int ep93xx_dma_terminate_all(struct dma_chan *chan)
{
	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
	struct ep93xx_dma_desc *desc, *_d;
	unsigned long flags;
	LIST_HEAD(list);

	spin_lock_irqsave(&edmac->lock, flags);
	/* First we disable and flush the DMA channel */
	edmac->edma->hw_shutdown(edmac);
	clear_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags);
	list_splice_init(&edmac->active, &list);
	list_splice_init(&edmac->queue, &list);
	/*
	 * We then re-enable the channel. This way we can continue submitting
	 * the descriptors by just calling ->hw_submit() again.
	 */
	edmac->edma->hw_setup(edmac);
	spin_unlock_irqrestore(&edmac->lock, flags);

	list_for_each_entry_safe(desc, _d, &list, node)
		ep93xx_dma_desc_put(edmac, desc);

	return 0;
}

static int ep93xx_dma_slave_config(struct dma_chan *chan,
				   struct dma_slave_config *config)
{
	struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
	enum dma_slave_buswidth width;
	unsigned long flags;
	u32 addr, ctrl;

	if (!edmac->edma->m2m)
		return -EINVAL;

	switch (config->direction) {
	case DMA_DEV_TO_MEM:
		width = config->src_addr_width;
		addr = config->src_addr;
		break;

	case DMA_MEM_TO_DEV:
		width = config->dst_addr_width;
		addr = config->dst_addr;
		break;

	default:
		return -EINVAL;
	}

	switch (width) {
	case DMA_SLAVE_BUSWIDTH_1_BYTE:
		ctrl = 0;
		break;
	case DMA_SLAVE_BUSWIDTH_2_BYTES:
		ctrl = M2M_CONTROL_PW_16;
		break;
	case DMA_SLAVE_BUSWIDTH_4_BYTES:
		ctrl = M2M_CONTROL_PW_32;
		break;
	default:
		return -EINVAL;
	}

	spin_lock_irqsave(&edmac->lock, flags);
	edmac->runtime_addr = addr;
	edmac->runtime_ctrl = ctrl;
	spin_unlock_irqrestore(&edmac->lock, flags);

	return 0;
}

/**
 * ep93xx_dma_tx_status - check if a transaction is completed
 * @chan: channel
 * @cookie: transaction specific cookie
 * @state: state of the transaction is stored here if given
 *
 * This function can be used to query state of a given transaction.
 */
static enum dma_status ep93xx_dma_tx_status(struct dma_chan *chan,
					    dma_cookie_t cookie,
					    struct dma_tx_state *state)
{
	return dma_cookie_status(chan, cookie, state);
}

/**
 * ep93xx_dma_issue_pending - push pending transactions to the hardware
 * @chan: channel
 *
 * When this function is called, all pending transactions are pushed to the
 * hardware and executed.
 */
static void ep93xx_dma_issue_pending(struct dma_chan *chan)
{
	ep93xx_dma_advance_work(to_ep93xx_dma_chan(chan));
}

static int __init ep93xx_dma_probe(struct platform_device *pdev)
{
	struct ep93xx_dma_platform_data *pdata = dev_get_platdata(&pdev->dev);
	struct ep93xx_dma_engine *edma;
	struct dma_device *dma_dev;
	size_t edma_size;
	int ret, i;

	edma_size = pdata->num_channels * sizeof(struct ep93xx_dma_chan);
	edma = kzalloc(sizeof(*edma) + edma_size, GFP_KERNEL);
	if (!edma)
		return -ENOMEM;

	dma_dev = &edma->dma_dev;
	edma->m2m = platform_get_device_id(pdev)->driver_data;
	edma->num_channels = pdata->num_channels;

	INIT_LIST_HEAD(&dma_dev->channels);
	for (i = 0; i < pdata->num_channels; i++) {
		const struct ep93xx_dma_chan_data *cdata = &pdata->channels[i];
		struct ep93xx_dma_chan *edmac = &edma->channels[i];

		edmac->chan.device = dma_dev;
		edmac->regs = cdata->base;
		edmac->irq = cdata->irq;
		edmac->edma = edma;

		edmac->clk = clk_get(NULL, cdata->name);
		if (IS_ERR(edmac->clk)) {
			dev_warn(&pdev->dev, "failed to get clock for %s\n",
				 cdata->name);
			continue;
		}

		spin_lock_init(&edmac->lock);
		INIT_LIST_HEAD(&edmac->active);
		INIT_LIST_HEAD(&edmac->queue);
		INIT_LIST_HEAD(&edmac->free_list);
		tasklet_init(&edmac->tasklet, ep93xx_dma_tasklet,
			     (unsigned long)edmac);

		list_add_tail(&edmac->chan.device_node,
			      &dma_dev->channels);
	}

	dma_cap_zero(dma_dev->cap_mask);
	dma_cap_set(DMA_SLAVE, dma_dev->cap_mask);
	dma_cap_set(DMA_CYCLIC, dma_dev->cap_mask);

	dma_dev->dev = &pdev->dev;
	dma_dev->device_alloc_chan_resources = ep93xx_dma_alloc_chan_resources;
	dma_dev->device_free_chan_resources = ep93xx_dma_free_chan_resources;
	dma_dev->device_prep_slave_sg = ep93xx_dma_prep_slave_sg;
	dma_dev->device_prep_dma_cyclic = ep93xx_dma_prep_dma_cyclic;
	dma_dev->device_config = ep93xx_dma_slave_config;
	dma_dev->device_terminate_all = ep93xx_dma_terminate_all;
	dma_dev->device_issue_pending = ep93xx_dma_issue_pending;
	dma_dev->device_tx_status = ep93xx_dma_tx_status;

	dma_set_max_seg_size(dma_dev->dev, DMA_MAX_CHAN_BYTES);

	if (edma->m2m) {
		dma_cap_set(DMA_MEMCPY, dma_dev->cap_mask);
		dma_dev->device_prep_dma_memcpy = ep93xx_dma_prep_dma_memcpy;

		edma->hw_setup = m2m_hw_setup;
		edma->hw_shutdown = m2m_hw_shutdown;
		edma->hw_submit = m2m_hw_submit;
		edma->hw_interrupt = m2m_hw_interrupt;
	} else {
		dma_cap_set(DMA_PRIVATE, dma_dev->cap_mask);

		edma->hw_setup = m2p_hw_setup;
		edma->hw_shutdown = m2p_hw_shutdown;
		edma->hw_submit = m2p_hw_submit;
		edma->hw_interrupt = m2p_hw_interrupt;
	}

	ret = dma_async_device_register(dma_dev);
	if (unlikely(ret)) {
		for (i = 0; i < edma->num_channels; i++) {
			struct ep93xx_dma_chan *edmac = &edma->channels[i];
			if (!IS_ERR_OR_NULL(edmac->clk))
				clk_put(edmac->clk);
		}
		kfree(edma);
	} else {
		dev_info(dma_dev->dev, "EP93xx M2%s DMA ready\n",
			 edma->m2m ? "M" : "P");
	}

	return ret;
}

static const struct platform_device_id ep93xx_dma_driver_ids[] = {
	{ "ep93xx-dma-m2p", 0 },
	{ "ep93xx-dma-m2m", 1 },
	{ },
};

static struct platform_driver ep93xx_dma_driver = {
	.driver		= {
		.name	= "ep93xx-dma",
	},
	.id_table	= ep93xx_dma_driver_ids,
};

static int __init ep93xx_dma_module_init(void)
{
	return platform_driver_probe(&ep93xx_dma_driver, ep93xx_dma_probe);
}
subsys_initcall(ep93xx_dma_module_init);

MODULE_AUTHOR("Mika Westerberg <mika.westerberg@iki.fi>");
MODULE_DESCRIPTION("EP93xx DMA driver");
MODULE_LICENSE("GPL");