/* SPDX-License-Identifier: GPL-2.0-only */
/*
 * Hypervisor stub
 *
 * Copyright (C) 2012 ARM Ltd.
 * Author:	Marc Zyngier <marc.zyngier@arm.com>
 */

#include <linux/init.h>
#include <linux/linkage.h>
#include <linux/irqchip/arm-gic-v3.h>

#include <asm/assembler.h>
#include <asm/kvm_arm.h>
#include <asm/kvm_asm.h>
#include <asm/ptrace.h>
#include <asm/virt.h>

	.text
	.pushsection	.hyp.text, "ax"

	.align 11

ENTRY(__hyp_stub_vectors)
	ventry	el2_sync_invalid		// Synchronous EL2t
	ventry	el2_irq_invalid			// IRQ EL2t
	ventry	el2_fiq_invalid			// FIQ EL2t
	ventry	el2_error_invalid		// Error EL2t

	ventry	el2_sync_invalid		// Synchronous EL2h
	ventry	el2_irq_invalid			// IRQ EL2h
	ventry	el2_fiq_invalid			// FIQ EL2h
	ventry	el2_error_invalid		// Error EL2h

	ventry	el1_sync			// Synchronous 64-bit EL1
	ventry	el1_irq_invalid			// IRQ 64-bit EL1
	ventry	el1_fiq_invalid			// FIQ 64-bit EL1
	ventry	el1_error_invalid		// Error 64-bit EL1

	ventry	el1_sync_invalid		// Synchronous 32-bit EL1
	ventry	el1_irq_invalid			// IRQ 32-bit EL1
	ventry	el1_fiq_invalid			// FIQ 32-bit EL1
	ventry	el1_error_invalid		// Error 32-bit EL1
ENDPROC(__hyp_stub_vectors)

	.align 11

el1_sync:
	cmp	x0, #HVC_SET_VECTORS
	b.ne	2f
	msr	vbar_el2, x1
	b	9f

2:	cmp	x0, #HVC_SOFT_RESTART
	b.ne	3f
	mov	x0, x2
	mov	x2, x4
	mov	x4, x1
	mov	x1, x3
	br	x4				// no return

3:	cmp	x0, #HVC_RESET_VECTORS
	beq	9f				// Nothing to reset!

	/* Someone called kvm_call_hyp() against the hyp-stub... */
	ldr	x0, =HVC_STUB_ERR
	eret

9:	mov	x0, xzr
	eret
ENDPROC(el1_sync)

.macro invalid_vector	label
\label:
	b \label
ENDPROC(\label)
.endm

	invalid_vector	el2_sync_invalid
	invalid_vector	el2_irq_invalid
	invalid_vector	el2_fiq_invalid
	invalid_vector	el2_error_invalid
	invalid_vector	el1_sync_invalid
	invalid_vector	el1_irq_invalid
	invalid_vector	el1_fiq_invalid
	invalid_vector	el1_error_invalid

/*
 * __hyp_set_vectors: Call this after boot to set the initial hypervisor
 * vectors as part of hypervisor installation.  On an SMP system, this should
 * be called on each CPU.
 *
 * x0 must be the physical address of the new vector table, and must be
 * 2KB aligned.
 *
 * Before calling this, you must check that the stub hypervisor is installed
 * everywhere, by waiting for any secondary CPUs to be brought up and then
 * checking that is_hyp_mode_available() is true.
 *
 * If not, there is a pre-existing hypervisor, some CPUs failed to boot, or
 * something else went wrong... in such cases, trying to install a new
 * hypervisor is unlikely to work as desired.
 *
 * When you call into your shiny new hypervisor, sp_el2 will contain junk,
 * so you will need to set that to something sensible at the new hypervisor's
 * initialisation entry point.
 */

ENTRY(__hyp_set_vectors)
	mov	x1, x0
	mov	x0, #HVC_SET_VECTORS
	hvc	#0
	ret
ENDPROC(__hyp_set_vectors)

ENTRY(__hyp_reset_vectors)
	mov	x0, #HVC_RESET_VECTORS
	hvc	#0
	ret
ENDPROC(__hyp_reset_vectors)