/* SPDX-License-Identifier: GPL-2.0+ */
/*
* pin-controller/pin-mux/pin-config/gpio-driver for Samsung's SoC's.
*
* Copyright (c) 2012 Samsung Electronics Co., Ltd.
* http://www.samsung.com
* Copyright (c) 2012 Linaro Ltd
* http://www.linaro.org
*
* Author: Thomas Abraham <thomas.ab@samsung.com>
*/
#ifndef __PINCTRL_SAMSUNG_H
#define __PINCTRL_SAMSUNG_H
#include <linux/pinctrl/pinctrl.h>
#include <linux/pinctrl/pinmux.h>
#include <linux/pinctrl/pinconf.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pinctrl/machine.h>
#include <linux/gpio/driver.h>
/**
* enum pincfg_type - possible pin configuration types supported.
* @PINCFG_TYPE_FUNC: Function configuration.
* @PINCFG_TYPE_DAT: Pin value configuration.
* @PINCFG_TYPE_PUD: Pull up/down configuration.
* @PINCFG_TYPE_DRV: Drive strength configuration.
* @PINCFG_TYPE_CON_PDN: Pin function in power down mode.
* @PINCFG_TYPE_PUD_PDN: Pull up/down configuration in power down mode.
*/
enum pincfg_type {
PINCFG_TYPE_FUNC,
PINCFG_TYPE_DAT,
PINCFG_TYPE_PUD,
PINCFG_TYPE_DRV,
PINCFG_TYPE_CON_PDN,
PINCFG_TYPE_PUD_PDN,
PINCFG_TYPE_NUM
};
/*
* pin configuration (pull up/down and drive strength) type and its value are
* packed together into a 16-bits. The upper 8-bits represent the configuration
* type and the lower 8-bits hold the value of the configuration type.
*/
#define PINCFG_TYPE_MASK 0xFF
#define PINCFG_VALUE_SHIFT 8
#define PINCFG_VALUE_MASK (0xFF << PINCFG_VALUE_SHIFT)
#define PINCFG_PACK(type, value) (((value) << PINCFG_VALUE_SHIFT) | type)
#define PINCFG_UNPACK_TYPE(cfg) ((cfg) & PINCFG_TYPE_MASK)
#define PINCFG_UNPACK_VALUE(cfg) (((cfg) & PINCFG_VALUE_MASK) >> \
PINCFG_VALUE_SHIFT)
/**
* enum eint_type - possible external interrupt types.
* @EINT_TYPE_NONE: bank does not support external interrupts
* @EINT_TYPE_GPIO: bank supportes external gpio interrupts
* @EINT_TYPE_WKUP: bank supportes external wakeup interrupts
* @EINT_TYPE_WKUP_MUX: bank supports multiplexed external wakeup interrupts
*
* Samsung GPIO controller groups all the available pins into banks. The pins
* in a pin bank can support external gpio interrupts or external wakeup
* interrupts or no interrupts at all. From a software perspective, the only
* difference between external gpio and external wakeup interrupts is that
* the wakeup interrupts can additionally wakeup the system if it is in
* suspended state.
*/
enum eint_type {
EINT_TYPE_NONE,
EINT_TYPE_GPIO,
EINT_TYPE_WKUP,
EINT_TYPE_WKUP_MUX,
};
/* maximum length of a pin in pin descriptor (example: "gpa0-0") */
#define PIN_NAME_LENGTH 10
#define PIN_GROUP(n, p, f) \
{ \
.name = n, \
.pins = p, \
.num_pins = ARRAY_SIZE(p), \
.func = f \
}
#define PMX_FUNC(n, g) \
{ \
.name = n, \
.groups = g, \
.num_groups = ARRAY_SIZE(g), \
}
struct samsung_pinctrl_drv_data;
/**
* struct samsung_pin_bank_type: pin bank type description
* @fld_width: widths of configuration bitfields (0 if unavailable)
* @reg_offset: offsets of configuration registers (don't care of width is 0)
*/
struct samsung_pin_bank_type {
u8 fld_width[PINCFG_TYPE_NUM];
u8 reg_offset[PINCFG_TYPE_NUM];
};
/**
* struct samsung_pin_bank_data: represent a controller pin-bank (init data).
* @type: type of the bank (register offsets and bitfield widths)
* @pctl_offset: starting offset of the pin-bank registers.
* @pctl_res_idx: index of base address for pin-bank registers.
* @nr_pins: number of pins included in this bank.
* @eint_func: function to set in CON register to configure pin as EINT.
* @eint_type: type of the external interrupt supported by the bank.
* @eint_mask: bit mask of pins which support EINT function.
* @eint_offset: SoC-specific EINT register or interrupt offset of bank.
* @name: name to be prefixed for each pin in this pin bank.
*/
struct samsung_pin_bank_data {
const struct samsung_pin_bank_type *type;
u32 pctl_offset;
u8 pctl_res_idx;
u8 nr_pins;
u8 eint_func;
enum eint_type eint_type;
u32 eint_mask;
u32 eint_offset;
const char *name;
};
/**
* struct samsung_pin_bank: represent a controller pin-bank.
* @type: type of the bank (register offsets and bitfield widths)
* @pctl_base: base address of the pin-bank registers
* @pctl_offset: starting offset of the pin-bank registers.
* @nr_pins: number of pins included in this bank.
* @eint_base: base address of the pin-bank EINT registers.
* @eint_func: function to set in CON register to configure pin as EINT.
* @eint_type: type of the external interrupt supported by the bank.
* @eint_mask: bit mask of pins which support EINT function.
* @eint_offset: SoC-specific EINT register or interrupt offset of bank.
* @name: name to be prefixed for each pin in this pin bank.
* @pin_base: starting pin number of the bank.
* @soc_priv: per-bank private data for SoC-specific code.
* @of_node: OF node of the bank.
* @drvdata: link to controller driver data
* @irq_domain: IRQ domain of the bank.
* @gpio_chip: GPIO chip of the bank.
* @grange: linux gpio pin range supported by this bank.
* @irq_chip: link to irq chip for external gpio and wakeup interrupts.
* @slock: spinlock protecting bank registers
* @pm_save: saved register values during suspend
*/
struct samsung_pin_bank {
const struct samsung_pin_bank_type *type;
void __iomem *pctl_base;
u32 pctl_offset;
u8 nr_pins;
void __iomem *eint_base;
u8 eint_func;
enum eint_type eint_type;
u32 eint_mask;
u32 eint_offset;
const char *name;
u32 pin_base;
void *soc_priv;
struct device_node *of_node;
struct samsung_pinctrl_drv_data *drvdata;
struct irq_domain *irq_domain;
struct gpio_chip gpio_chip;
struct pinctrl_gpio_range grange;
struct exynos_irq_chip *irq_chip;
spinlock_t slock;
u32 pm_save[PINCFG_TYPE_NUM + 1]; /* +1 to handle double CON registers*/
};
/**
* struct samsung_retention_data: runtime pin-bank retention control data.
* @regs: array of PMU registers to control pad retention.
* @nr_regs: number of registers in @regs array.
* @value: value to store to registers to turn off retention.
* @refcnt: atomic counter if retention control affects more than one bank.
* @priv: retention control code private data
* @enable: platform specific callback to enter retention mode.
* @disable: platform specific callback to exit retention mode.
**/
struct samsung_retention_ctrl {
const u32 *regs;
int nr_regs;
u32 value;
atomic_t *refcnt;
void *priv;
void (*enable)(struct samsung_pinctrl_drv_data *);
void (*disable)(struct samsung_pinctrl_drv_data *);
};
/**
* struct samsung_retention_data: represent a pin-bank retention control data.
* @regs: array of PMU registers to control pad retention.
* @nr_regs: number of registers in @regs array.
* @value: value to store to registers to turn off retention.
* @refcnt: atomic counter if retention control affects more than one bank.
* @init: platform specific callback to initialize retention control.
**/
struct samsung_retention_data {
const u32 *regs;
int nr_regs;
u32 value;
atomic_t *refcnt;
struct samsung_retention_ctrl *(*init)(struct samsung_pinctrl_drv_data *,
const struct samsung_retention_data *);
};
/**
* struct samsung_pin_ctrl: represent a pin controller.
* @pin_banks: list of pin banks included in this controller.
* @nr_banks: number of pin banks.
* @nr_ext_resources: number of the extra base address for pin banks.
* @retention_data: configuration data for retention control.
* @eint_gpio_init: platform specific callback to setup the external gpio
* interrupts for the controller.
* @eint_wkup_init: platform specific callback to setup the external wakeup
* interrupts for the controller.
* @suspend: platform specific suspend callback, executed during pin controller
* device suspend, see samsung_pinctrl_suspend()
* @resume: platform specific resume callback, executed during pin controller
* device suspend, see samsung_pinctrl_resume()
*
* External wakeup interrupts must define at least eint_wkup_init,
* retention_data and suspend in order for proper suspend/resume to work.
*/
struct samsung_pin_ctrl {
const struct samsung_pin_bank_data *pin_banks;
unsigned int nr_banks;
unsigned int nr_ext_resources;
const struct samsung_retention_data *retention_data;
int (*eint_gpio_init)(struct samsung_pinctrl_drv_data *);
int (*eint_wkup_init)(struct samsung_pinctrl_drv_data *);
void (*suspend)(struct samsung_pinctrl_drv_data *);
void (*resume)(struct samsung_pinctrl_drv_data *);
};
/**
* struct samsung_pinctrl_drv_data: wrapper for holding driver data together.
* @node: global list node
* @virt_base: register base address of the controller; this will be equal
* to each bank samsung_pin_bank->pctl_base and used on legacy
* platforms (like S3C24XX or S3C64XX) which has to access the base
* through samsung_pinctrl_drv_data, not samsung_pin_bank).
* @dev: device instance representing the controller.
* @irq: interrpt number used by the controller to notify gpio interrupts.
* @ctrl: pin controller instance managed by the driver.
* @pctl: pin controller descriptor registered with the pinctrl subsystem.
* @pctl_dev: cookie representing pinctrl device instance.
* @pin_groups: list of pin groups available to the driver.
* @nr_groups: number of such pin groups.
* @pmx_functions: list of pin functions available to the driver.
* @nr_function: number of such pin functions.
* @pin_base: starting system wide pin number.
* @nr_pins: number of pins supported by the controller.
* @retention_ctrl: retention control runtime data.
* @suspend: platform specific suspend callback, executed during pin controller
* device suspend, see samsung_pinctrl_suspend()
* @resume: platform specific resume callback, executed during pin controller
* device suspend, see samsung_pinctrl_resume()
*/
struct samsung_pinctrl_drv_data {
struct list_head node;
void __iomem *virt_base;
struct device *dev;
int irq;
struct pinctrl_desc pctl;
struct pinctrl_dev *pctl_dev;
const struct samsung_pin_group *pin_groups;
unsigned int nr_groups;
const struct samsung_pmx_func *pmx_functions;
unsigned int nr_functions;
struct samsung_pin_bank *pin_banks;
unsigned int nr_banks;
unsigned int pin_base;
unsigned int nr_pins;
struct samsung_retention_ctrl *retention_ctrl;
void (*suspend)(struct samsung_pinctrl_drv_data *);
void (*resume)(struct samsung_pinctrl_drv_data *);
};
/**
* struct samsung_pinctrl_of_match_data: OF match device specific configuration data.
* @ctrl: array of pin controller data.
* @num_ctrl: size of array @ctrl.
*/
struct samsung_pinctrl_of_match_data {
const struct samsung_pin_ctrl *ctrl;
unsigned int num_ctrl;
};
/**
* struct samsung_pin_group: represent group of pins of a pinmux function.
* @name: name of the pin group, used to lookup the group.
* @pins: the pins included in this group.
* @num_pins: number of pins included in this group.
* @func: the function number to be programmed when selected.
*/
struct samsung_pin_group {
const char *name;
const unsigned int *pins;
u8 num_pins;
u8 func;
};
/**
* struct samsung_pmx_func: represent a pin function.
* @name: name of the pin function, used to lookup the function.
* @groups: one or more names of pin groups that provide this function.
* @num_groups: number of groups included in @groups.
*/
struct samsung_pmx_func {
const char *name;
const char **groups;
u8 num_groups;
u32 val;
};
/* list of all exported SoC specific data */
extern const struct samsung_pinctrl_of_match_data exynos3250_of_data;
extern const struct samsung_pinctrl_of_match_data exynos4210_of_data;
extern const struct samsung_pinctrl_of_match_data exynos4x12_of_data;
extern const struct samsung_pinctrl_of_match_data exynos5250_of_data;
extern const struct samsung_pinctrl_of_match_data exynos5260_of_data;
extern const struct samsung_pinctrl_of_match_data exynos5410_of_data;
extern const struct samsung_pinctrl_of_match_data exynos5420_of_data;
extern const struct samsung_pinctrl_of_match_data exynos5433_of_data;
extern const struct samsung_pinctrl_of_match_data exynos7_of_data;
extern const struct samsung_pinctrl_of_match_data s3c64xx_of_data;
extern const struct samsung_pinctrl_of_match_data s3c2412_of_data;
extern const struct samsung_pinctrl_of_match_data s3c2416_of_data;
extern const struct samsung_pinctrl_of_match_data s3c2440_of_data;
extern const struct samsung_pinctrl_of_match_data s3c2450_of_data;
extern const struct samsung_pinctrl_of_match_data s5pv210_of_data;
#endif /* __PINCTRL_SAMSUNG_H */