/* SPDX-License-Identifier: GPL-2.0 */
/* Copyright(c) 2009-2013 Realtek Corporation.*/
#ifndef __RTL8723E_PWRSEQ_H__
#define __RTL8723E_PWRSEQ_H__
#include "../pwrseqcmd.h"
/* Check document WM-20110607-Paul-RTL8188EE_Power_Architecture-R02.vsd
* There are 6 HW Power States:
* 0: POFF--Power Off
* 1: PDN--Power Down
* 2: CARDEMU--Card Emulation
* 3: ACT--Active Mode
* 4: LPS--Low Power State
* 5: SUS--Suspend
*
* The transision from different states are defined below
* TRANS_CARDEMU_TO_ACT
* TRANS_ACT_TO_CARDEMU
* TRANS_CARDEMU_TO_SUS
* TRANS_SUS_TO_CARDEMU
* TRANS_CARDEMU_TO_PDN
* TRANS_ACT_TO_LPS
* TRANS_LPS_TO_ACT
*
* TRANS_END
* PWR SEQ Version: rtl8188ee_PwrSeq_V09.h
*/
#define RTL8188EE_TRANS_CARDEMU_TO_ACT_STEPS 10
#define RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS 10
#define RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS 10
#define RTL8188EE_TRANS_SUS_TO_CARDEMU_STEPS 10
#define RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS 10
#define RTL8188EE_TRANS_PDN_TO_CARDEMU_STEPS 10
#define RTL8188EE_TRANS_ACT_TO_LPS_STEPS 15
#define RTL8188EE_TRANS_LPS_TO_ACT_STEPS 15
#define RTL8188EE_TRANS_END_STEPS 1
/* The following macros have the following format:
* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value
* comments },
*/
#define RTL8188EE_TRANS_CARDEMU_TO_ACT \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1) \
/* wait till 0x04[17] = 1 power ready*/}, \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0)|BIT(1), 0 \
/* 0x02[1:0] = 0 reset BB*/}, \
{0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \
/*0x24[23] = 2b'01 schmit trigger */}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0 \
/* 0x04[15] = 0 disable HWPDN (control by DRV)*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4)|BIT(3), 0 \
/*0x04[12:11] = 2b'00 disable WL suspend*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0) \
/*0x04[8] = 1 polling until return 0*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0 \
/*wait till 0x04[8] = 0*/}, \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \
/*LDO normal mode*/}, \
{0x0074, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \
/*SDIO Driving*/},
#define RTL8188EE_TRANS_ACT_TO_CARDEMU \
{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \
/*0x1F[7:0] = 0 turn off RF*/}, \
{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \
/*LDO Sleep mode*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1) \
/*0x04[9] = 1 turn off MAC by HW state machine*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0 \
/*wait till 0x04[9] = 0 polling until return 0 to disable*/},
#define RTL8188EE_TRANS_CARDEMU_TO_SUS \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3) \
/*0x04[12:11] = 2b'01enable WL suspend*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)|BIT(4) \
/*0x04[12:11] = 2b'11enable WL suspend for PCIe*/}, \
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, BIT(7) \
/* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */},\
{0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \
/*Clear SIC_EN register 0x40[12] = 1'b0 */}, \
{0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \
/*Set USB suspend enable local register 0xfe10[4]=1 */}, \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0) \
/*Set SDIO suspend local register*/}, \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0 \
/*wait power state to suspend*/},
#define RTL8188EE_TRANS_SUS_TO_CARDEMU \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0 \
/*Set SDIO suspend local register*/}, \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1) \
/*wait power state to suspend*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), 0 \
/*0x04[12:11] = 2b'00 disable WL suspend*/},
#define RTL8188EE_TRANS_CARDEMU_TO_CARDDIS \
{0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \
/*0x24[23] = 2b'01 schmit trigger */}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3) \
/*0x04[12:11] = 2b'01 enable WL suspend*/}, \
{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \
/* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */},\
{0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \
/*Clear SIC_EN register 0x40[12] = 1'b0 */}, \
{0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \
/*Set USB suspend enable local register 0xfe10[4]=1 */}, \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0) \
/*Set SDIO suspend local register*/}, \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0 \
/*wait power state to suspend*/},
#define RTL8188EE_TRANS_CARDDIS_TO_CARDEMU \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0 \
/*Set SDIO suspend local register*/}, \
{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1) \
/*wait power state to suspend*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0 \
/*0x04[12:11] = 2b'00 disable WL suspend*/},
#define RTL8188EE_TRANS_CARDEMU_TO_PDN \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0/* 0x04[16] = 0*/}, \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \
/* 0x04[15] = 1*/},
#define RTL8188EE_TRANS_PDN_TO_CARDEMU \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0/* 0x04[15] = 0*/},
#define RTL8188EE_TRANS_ACT_TO_LPS \
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F \
/*Tx Pause*/}, \
{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \
/*Should be zero if no packet is transmitting*/}, \
{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \
/*Should be zero if no packet is transmitting*/}, \
{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \
/*Should be zero if no packet is transmitting*/}, \
{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \
/*Should be zero if no packet is transmitting*/}, \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0 \
/*CCK and OFDM are disabled,and clock are gated*/}, \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US \
/*Delay 1us*/}, \
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F \
/*Reset MAC TRX*/}, \
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0 \
/*check if removed later*/}, \
{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5) \
/*Respond TxOK to scheduler*/},
#define RTL8188EE_TRANS_LPS_TO_ACT \
{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84 \
/*SDIO RPWM*/}, \
{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \
/*USB RPWM*/}, \
{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \
/*PCIe RPWM*/}, \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS \
/*Delay*/}, \
{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \
/*. 0x08[4] = 0 switch TSF to 40M*/}, \
{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(7), 0 \
/*Polling 0x109[7]=0 TSF in 40M*/}, \
{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6)|BIT(7), 0 \
/*. 0x29[7:6] = 2b'00 enable BB clock*/}, \
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1) \
/*. 0x101[1] = 1*/}, \
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF \
/*. 0x100[7:0] = 0xFF enable WMAC TRX*/}, \
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0) \
/*. 0x02[1:0] = 2b'11 enable BB macro*/}, \
{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \
/*. 0x522 = 0*/},
#define RTL8188EE_TRANS_END \
{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
0, PWR_CMD_END, 0, 0}
extern struct wlan_pwr_cfg rtl8188ee_power_on_flow
[RTL8188EE_TRANS_CARDEMU_TO_ACT_STEPS +
RTL8188EE_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8188ee_radio_off_flow
[RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8188EE_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8188ee_card_disable_flow
[RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8188EE_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8188ee_card_enable_flow
[RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8188EE_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8188ee_suspend_flow
[RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS +
RTL8188EE_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8188ee_resume_flow
[RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS +
RTL8188EE_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8188ee_hwpdn_flow
[RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS +
RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS +
RTL8188EE_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8188ee_enter_lps_flow
[RTL8188EE_TRANS_ACT_TO_LPS_STEPS +
RTL8188EE_TRANS_END_STEPS];
extern struct wlan_pwr_cfg rtl8188ee_leave_lps_flow
[RTL8188EE_TRANS_LPS_TO_ACT_STEPS +
RTL8188EE_TRANS_END_STEPS];
/* RTL8723 Power Configuration CMDs for PCIe interface */
#define RTL8188EE_NIC_PWR_ON_FLOW rtl8188ee_power_on_flow
#define RTL8188EE_NIC_RF_OFF_FLOW rtl8188ee_radio_off_flow
#define RTL8188EE_NIC_DISABLE_FLOW rtl8188ee_card_disable_flow
#define RTL8188EE_NIC_ENABLE_FLOW rtl8188ee_card_enable_flow
#define RTL8188EE_NIC_SUSPEND_FLOW rtl8188ee_suspend_flow
#define RTL8188EE_NIC_RESUME_FLOW rtl8188ee_resume_flow
#define RTL8188EE_NIC_PDN_FLOW rtl8188ee_hwpdn_flow
#define RTL8188EE_NIC_LPS_ENTER_FLOW rtl8188ee_enter_lps_flow
#define RTL8188EE_NIC_LPS_LEAVE_FLOW rtl8188ee_leave_lps_flow
#endif