Training courses

Kernel and Embedded Linux

Bootlin training courses

Embedded Linux, kernel,
Yocto Project, Buildroot, real-time,
graphics, boot time, debugging...

Bootlin logo

Elixir Cross Referencer

Open Menu /Documentation/devicetree/bindings/phy/ti-phy-gmii-sel.txt 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
CPSW Port's Interface Mode Selection PHY Tree Bindings
-----------------------------------------------

TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports
two 10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII interfaces.
The interface mode is selected by configuring the MII mode selection register(s)
(GMII_SEL) in the System Control Module chapter (SCM). GMII_SEL register(s) and
bit fields placement in SCM are different between SoCs while fields meaning
is the same.
                                               +--------------+
        +-------------------------------+      |SCM           |
        |                     CPSW      |      |  +---------+ |
        |        +--------------------------------+gmii_sel | |
        |        |                      |      |  +---------+ |
        |   +----v---+     +--------+   |      +--------------+
        |   |Port 1..<--+-->GMII/MII<------->
        |   |        |  |  |        |   |
        |   +--------+  |  +--------+   |
        |               |               |
        |               |  +--------+   |
        |               |  | RMII   <------->
        |               +-->        |   |
        |               |  +--------+   |
        |               |               |
        |               |  +--------+   |
        |               |  | RGMII  <------->
        |               +-->        |   |
        |                  +--------+   |
        +-------------------------------+

CPSW Port's Interface Mode Selection PHY describes MII interface mode between
CPSW Port and Ethernet PHY which depends on Eth PHY and board configuration.

CPSW Port's Interface Mode Selection PHY device should defined as child device
of SCM node (scm_conf) and can be attached to each CPSW port node using standard
PHY bindings (See phy/phy-bindings.txt).

Required properties:
- compatible		: Should be "ti,am3352-phy-gmii-sel" for am335x platform
			  "ti,dra7xx-phy-gmii-sel" for dra7xx/am57xx platform
			  "ti,am43xx-phy-gmii-sel" for am43xx platform
			  "ti,dm814-phy-gmii-sel" for dm814x platform
- reg			: Address and length of the register set for the device
- #phy-cells		: must be 2.
			  cell 1 - CPSW port number (starting from 1)
			  cell 2 - RMII refclk mode

Examples:
	phy_gmii_sel: phy-gmii-sel {
		compatible = "ti,am3352-phy-gmii-sel";
		reg = <0x650 0x4>;
		#phy-cells = <2>;
	};

	mac: ethernet@4a100000 {
		compatible = "ti,am335x-cpsw","ti,cpsw";
		...

		cpsw_emac0: slave@4a100200 {
			...
			phys = <&phy_gmii_sel 1 1>;
		};

		cpsw_emac1: slave@4a100300 {
			...
			phys = <&phy_gmii_sel 2 1>;
		};
	};