// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
/*
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
*/
/dts-v1/;
#include "stm32mp157c.dtsi"
#include "stm32mp157xac-pinctrl.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/mfd/st,stpmic1.h>
/ {
model = "Arrow Electronics STM32MP157A Avenger96 board";
compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
aliases {
ethernet0 = ðernet0;
mmc0 = &sdmmc1;
serial0 = &uart4;
serial1 = &uart7;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@c0000000 {
device_type = "memory";
reg = <0xc0000000 0x40000000>;
};
led {
compatible = "gpio-leds";
led1 {
label = "green:user1";
gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
led2 {
label = "green:user2";
gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
default-state = "off";
};
led3 {
label = "green:user3";
gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc1";
default-state = "off";
};
led4 {
label = "green:user3";
gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "none";
default-state = "off";
panic-indicator;
};
led5 {
label = "yellow:wifi";
gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tx";
default-state = "off";
};
led6 {
label = "blue:bt";
gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bluetooth-power";
default-state = "off";
};
};
};
ðernet0 {
status = "okay";
pinctrl-0 = <ðernet0_rgmii_pins_a>;
pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
pinctrl-names = "default", "sleep";
phy-mode = "rgmii";
max-speed = <1000>;
phy-handle = <&phy0>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy0: ethernet-phy@7 {
reg = <7>;
};
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_b>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/delete-property/dmas;
/delete-property/dma-names;
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/delete-property/dmas;
/delete-property/dma-names;
};
&i2c4 {
pinctrl-names = "default";
pinctrl-0 = <&i2c4_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/delete-property/dmas;
/delete-property/dma-names;
pmic: stpmic@33 {
compatible = "st,stpmic1";
reg = <0x33>;
interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
status = "okay";
st,main-control-register = <0x04>;
st,vin-control-register = <0xc0>;
st,usb-control-register = <0x30>;
regulators {
compatible = "st,stpmic1-regulators";
ldo1-supply = <&v3v3>;
ldo2-supply = <&v3v3>;
ldo3-supply = <&vdd_ddr>;
ldo5-supply = <&v3v3>;
ldo6-supply = <&v3v3>;
pwr_sw1-supply = <&bst_out>;
pwr_sw2-supply = <&bst_out>;
vddcore: buck1 {
regulator-name = "vddcore";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
vdd_ddr: buck2 {
regulator-name = "vdd_ddr";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
vdd: buck3 {
regulator-name = "vdd";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
st,mask_reset;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
v3v3: buck4 {
regulator-name = "v3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-over-current-protection;
regulator-initial-mode = <0>;
};
vdda: ldo1 {
regulator-name = "vdda";
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>;
interrupts = <IT_CURLIM_LDO1 0>;
interrupt-parent = <&pmic>;
};
v2v8: ldo2 {
regulator-name = "v2v8";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
interrupts = <IT_CURLIM_LDO2 0>;
interrupt-parent = <&pmic>;
};
vtt_ddr: ldo3 {
regulator-name = "vtt_ddr";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <750000>;
regulator-always-on;
regulator-over-current-protection;
};
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
interrupt-parent = <&pmic>;
};
vdd_sd: ldo5 {
regulator-name = "vdd_sd";
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>;
interrupts = <IT_CURLIM_LDO5 0>;
interrupt-parent = <&pmic>;
regulator-boot-on;
};
v1v8: ldo6 {
regulator-name = "v1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
interrupts = <IT_CURLIM_LDO6 0>;
interrupt-parent = <&pmic>;
regulator-enable-ramp-delay = <300000>;
};
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
regulator-over-current-protection;
};
bst_out: boost {
regulator-name = "bst_out";
interrupts = <IT_OCP_BOOST 0>;
interrupt-parent = <&pmic>;
};
vbus_otg: pwr_sw1 {
regulator-name = "vbus_otg";
interrupts = <IT_OCP_OTG 0>;
interrupt-parent = <&pmic>;
regulator-active-discharge;
};
vbus_sw: pwr_sw2 {
regulator-name = "vbus_sw";
interrupts = <IT_OCP_SWOUT 0>;
interrupt-parent = <&pmic>;
regulator-active-discharge;
};
};
onkey {
compatible = "st,stpmic1-onkey";
interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
interrupt-names = "onkey-falling", "onkey-rising";
status = "okay";
};
watchdog {
compatible = "st,stpmic1-wdt";
status = "disabled";
};
};
};
&iwdg2 {
timeout-sec = <32>;
status = "okay";
};
&rng1 {
status = "okay";
};
&rtc {
status = "okay";
};
&sdmmc1 {
pinctrl-names = "default", "opendrain", "sleep";
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
broken-cd;
st,sig-dir;
st,neg-edge;
st,use-ckin;
bus-width = <4>;
vmmc-supply = <&vdd_sd>;
status = "okay";
};
&uart4 {
/* On Low speed expansion header */
label = "LS-UART1";
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_b>;
status = "okay";
};
&uart7 {
/* On Low speed expansion header */
label = "LS-UART0";
pinctrl-names = "default";
pinctrl-0 = <&uart7_pins_a>;
status = "okay";
};