/* SPDX-License-Identifier: GPL-2.0-only */ /* * arch/arm/mach-pxa/include/mach/viper.h * * Author: Ian Campbell * Created: Feb 03, 2003 * Copyright: Arcom Control Systems. * * Maintained by Marc Zyngier <maz@misterjones.org> * <marc.zyngier@altran.com> * * Created based on lubbock.h: * Author: Nicolas Pitre * Created: Jun 15, 2001 * Copyright: MontaVista Software Inc. */ #ifndef ARCH_VIPER_H #define ARCH_VIPER_H #define VIPER_BOOT_PHYS PXA_CS0_PHYS #define VIPER_FLASH_PHYS PXA_CS1_PHYS #define VIPER_ETH_PHYS PXA_CS2_PHYS #define VIPER_USB_PHYS PXA_CS3_PHYS #define VIPER_ETH_DATA_PHYS PXA_CS4_PHYS #define VIPER_CPLD_PHYS PXA_CS5_PHYS #define VIPER_CPLD_BASE (0xf0000000) #define VIPER_PC104IO_BASE (0xf1000000) #define VIPER_USB_BASE (0xf1800000) #define VIPER_ETH_GPIO (0) #define VIPER_CPLD_GPIO (1) #define VIPER_USB_GPIO (2) #define VIPER_UARTA_GPIO (4) #define VIPER_UARTB_GPIO (3) #define VIPER_CF_CD_GPIO (32) #define VIPER_CF_RDY_GPIO (8) #define VIPER_BCKLIGHT_EN_GPIO (9) #define VIPER_LCD_EN_GPIO (10) #define VIPER_PSU_DATA_GPIO (6) #define VIPER_PSU_CLK_GPIO (11) #define VIPER_UART_SHDN_GPIO (12) #define VIPER_BRIGHTNESS_GPIO (16) #define VIPER_PSU_nCS_LD_GPIO (19) #define VIPER_UPS_GPIO (20) #define VIPER_CF_POWER_GPIO (82) #define VIPER_TPM_I2C_SDA_GPIO (26) #define VIPER_TPM_I2C_SCL_GPIO (27) #define VIPER_RTC_I2C_SDA_GPIO (83) #define VIPER_RTC_I2C_SCL_GPIO (84) #define VIPER_CPLD_P2V(x) ((x) - VIPER_CPLD_PHYS + VIPER_CPLD_BASE) #define VIPER_CPLD_V2P(x) ((x) - VIPER_CPLD_BASE + VIPER_CPLD_PHYS) #ifndef __ASSEMBLY__ # define __VIPER_CPLD_REG(x) (*((volatile u16 *)VIPER_CPLD_P2V(x))) #endif /* board level registers in the CPLD: (offsets from CPLD_BASE) ... */ /* ... Physical addresses */ #define _VIPER_LO_IRQ_STATUS (VIPER_CPLD_PHYS + 0x100000) #define _VIPER_ICR_PHYS (VIPER_CPLD_PHYS + 0x100002) #define _VIPER_HI_IRQ_STATUS (VIPER_CPLD_PHYS + 0x100004) #define _VIPER_VERSION_PHYS (VIPER_CPLD_PHYS + 0x100006) #define VIPER_UARTA_PHYS (VIPER_CPLD_PHYS + 0x300010) #define VIPER_UARTB_PHYS (VIPER_CPLD_PHYS + 0x300000) #define _VIPER_SRAM_BASE (VIPER_CPLD_PHYS + 0x800000) /* ... Virtual addresses */ #define VIPER_LO_IRQ_STATUS __VIPER_CPLD_REG(_VIPER_LO_IRQ_STATUS) #define VIPER_HI_IRQ_STATUS __VIPER_CPLD_REG(_VIPER_HI_IRQ_STATUS) #define VIPER_VERSION __VIPER_CPLD_REG(_VIPER_VERSION_PHYS) #define VIPER_ICR __VIPER_CPLD_REG(_VIPER_ICR_PHYS) /* Decode VIPER_VERSION register */ #define VIPER_CPLD_REVISION(x) (((x) >> 5) & 0x7) #define VIPER_BOARD_VERSION(x) (((x) >> 3) & 0x3) #define VIPER_BOARD_ISSUE(x) (((x) >> 0) & 0x7) /* Interrupt and Configuration Register (VIPER_ICR) */ /* This is a write only register. Only CF_RST is used under Linux */ #define VIPER_ICR_RETRIG (1 << 0) #define VIPER_ICR_AUTO_CLR (1 << 1) #define VIPER_ICR_R_DIS (1 << 2) #define VIPER_ICR_CF_RST (1 << 3) #endif |