// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
*
* Based on "omap4.dtsi"
*/
#include <dt-bindings/bus/ti-sysc.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/omap.h>
#include <dt-bindings/clock/omap5.h>
/ {
#address-cells = <2>;
#size-cells = <2>;
compatible = "ti,omap5";
interrupt-parent = <&wakeupgen>;
chosen { };
aliases {
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
i2c3 = &i2c4;
i2c4 = &i2c5;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
serial3 = &uart4;
serial4 = &uart5;
serial5 = &uart6;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x0>;
operating-points = <
/* kHz uV */
1000000 1060000
1500000 1250000
>;
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
clock-latency = <300000>; /* From omap-cpufreq driver */
/* cooling options */
#cooling-cells = <2>; /* min followed by max */
};
cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x1>;
operating-points = <
/* kHz uV */
1000000 1060000
1500000 1250000
>;
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
clock-latency = <300000>; /* From omap-cpufreq driver */
/* cooling options */
#cooling-cells = <2>; /* min followed by max */
};
};
thermal-zones {
#include "omap4-cpu-thermal.dtsi"
#include "omap5-gpu-thermal.dtsi"
#include "omap5-core-thermal.dtsi"
};
timer {
compatible = "arm,armv7-timer";
/* PPI secure/nonsecure IRQ */
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
interrupt-parent = <&gic>;
};
pmu {
compatible = "arm,cortex-a15-pmu";
interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
};
gic: interrupt-controller@48211000 {
compatible = "arm,cortex-a15-gic";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0 0x48211000 0 0x1000>,
<0 0x48212000 0 0x2000>,
<0 0x48214000 0 0x2000>,
<0 0x48216000 0 0x2000>;
interrupt-parent = <&gic>;
};
wakeupgen: interrupt-controller@48281000 {
compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0 0x48281000 0 0x1000>;
interrupt-parent = <&gic>;
};
/*
* The soc node represents the soc top level view. It is used for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
*/
soc {
compatible = "ti,omap-infra";
mpu {
compatible = "ti,omap4-mpu";
ti,hwmods = "mpu";
sram = <&ocmcram>;
};
};
/*
* XXX: Use a flat representation of the OMAP3 interconnect.
* The real OMAP interconnect network is quite complex.
* Since it will not bring real advantage to represent that in DT for
* the moment, just use a fake OCP bus entry to represent the whole bus
* hierarchy.
*/
ocp {
compatible = "ti,omap5-l3-noc", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0 0xc0000000>;
ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
reg = <0 0x44000000 0 0x2000>,
<0 0x44800000 0 0x3000>,
<0 0x45000000 0 0x4000>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
l4_wkup: interconnect@4ae00000 {
};
l4_cfg: interconnect@4a000000 {
};
l4_per: interconnect@48000000 {
};
l4_abe: interconnect@40100000 {
};
ocmcram: ocmcram@40300000 {
compatible = "mmio-sram";
reg = <0x40300000 0x20000>; /* 128k */
};
gpmc: gpmc@50000000 {
compatible = "ti,omap4430-gpmc";
reg = <0x50000000 0x1000>;
#address-cells = <2>;
#size-cells = <1>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&sdma 4>;
dma-names = "rxtx";
gpmc,num-cs = <8>;
gpmc,num-waitpins = <4>;
ti,hwmods = "gpmc";
clocks = <&l3_iclk_div>;
clock-names = "fck";
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
};
mmu_dsp: mmu@4a066000 {
compatible = "ti,omap4-iommu";
reg = <0x4a066000 0x100>;
interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmu_dsp";
#iommu-cells = <0>;
};
mmu_ipu: mmu@55082000 {
compatible = "ti,omap4-iommu";
reg = <0x55082000 0x100>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmu_ipu";
#iommu-cells = <0>;
ti,iommu-bus-err-back;
};
dmm@4e000000 {
compatible = "ti,omap5-dmm";
reg = <0x4e000000 0x800>;
interrupts = <0 113 0x4>;
ti,hwmods = "dmm";
};
emif1: emif@4c000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif1";
ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4c000000 0x400>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
hw-caps-temp-alert;
};
emif2: emif@4d000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif2";
ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4d000000 0x400>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
hw-caps-temp-alert;
};
bandgap: bandgap@4a0021e0 {
reg = <0x4a0021e0 0xc
0x4a00232c 0xc
0x4a002380 0x2c
0x4a0023C0 0x3c>;
interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
compatible = "ti,omap5430-bandgap";
#thermal-sensor-cells = <1>;
};
/* OCP2SCP3 */
sata: sata@4a141100 {
compatible = "snps,dwc-ahci";
reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
phys = <&sata_phy>;
phy-names = "sata-phy";
clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 8>;
ti,hwmods = "sata";
ports-implemented = <0x1>;
};
target-module@56000000 {
compatible = "ti,sysc-omap4", "ti,sysc";
reg = <0x5600fe00 0x4>,
<0x5600fe10 0x4>;
reg-names = "rev", "sysc";
ti,sysc-midle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
ti,sysc-sidle = <SYSC_IDLE_FORCE>,
<SYSC_IDLE_NO>,
<SYSC_IDLE_SMART>;
clocks = <&gpu_clkctrl OMAP5_GPU_CLKCTRL 0>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x56000000 0x2000000>;
/*
* Closed source PowerVR driver, no child device
* binding or driver in mainline
*/
};
dss: dss@58000000 {
compatible = "ti,omap5-dss";
reg = <0x58000000 0x80>;
status = "disabled";
ti,hwmods = "dss_core";
clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges;
dispc@58001000 {
compatible = "ti,omap5-dispc";
reg = <0x58001000 0x1000>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "dss_dispc";
clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>;
clock-names = "fck";
};
rfbi: encoder@58002000 {
compatible = "ti,omap5-rfbi";
reg = <0x58002000 0x100>;
status = "disabled";
ti,hwmods = "dss_rfbi";
clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>, <&l3_iclk_div>;
clock-names = "fck", "ick";
};
dsi1: encoder@58004000 {
compatible = "ti,omap5-dsi";
reg = <0x58004000 0x200>,
<0x58004200 0x40>,
<0x58004300 0x40>;
reg-names = "proto", "phy", "pll";
interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_dsi1";
clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>,
<&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
clock-names = "fck", "sys_clk";
};
dsi2: encoder@58005000 {
compatible = "ti,omap5-dsi";
reg = <0x58009000 0x200>,
<0x58009200 0x40>,
<0x58009300 0x40>;
reg-names = "proto", "phy", "pll";
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_dsi2";
clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 8>,
<&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
clock-names = "fck", "sys_clk";
};
hdmi: encoder@58060000 {
compatible = "ti,omap5-hdmi";
reg = <0x58040000 0x200>,
<0x58040200 0x80>,
<0x58040300 0x80>,
<0x58060000 0x19000>;
reg-names = "wp", "pll", "phy", "core";
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_hdmi";
clocks = <&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 9>,
<&dss_clkctrl OMAP5_DSS_CORE_CLKCTRL 10>;
clock-names = "fck", "sys_clk";
dmas = <&sdma 76>;
dma-names = "audio_tx";
};
};
abb_mpu: regulator-abb-mpu {
compatible = "ti,abb-v2";
regulator-name = "abb_mpu";
#address-cells = <0>;
#size-cells = <0>;
clocks = <&sys_clkin>;
ti,settling-time = <50>;
ti,clock-cycles = <16>;
reg = <0x4ae07cdc 0x8>, <0x4ae06014 0x4>,
<0x4a0021c4 0x8>, <0x4ae0c318 0x4>;
reg-names = "base-address", "int-address",
"efuse-address", "ldo-address";
ti,tranxdone-status-mask = <0x80>;
/* LDOVBBMPU_MUX_CTRL */
ti,ldovbb-override-mask = <0x400>;
/* LDOVBBMPU_VSET_OUT */
ti,ldovbb-vset-mask = <0x1F>;
/*
* NOTE: only FBB mode used but actual vset will
* determine final biasing
*/
ti,abb_info = <
/*uV ABB efuse rbb_m fbb_m vset_m*/
1060000 0 0x0 0 0x02000000 0x01F00000
1250000 0 0x4 0 0x02000000 0x01F00000
>;
};
abb_mm: regulator-abb-mm {
compatible = "ti,abb-v2";
regulator-name = "abb_mm";
#address-cells = <0>;
#size-cells = <0>;
clocks = <&sys_clkin>;
ti,settling-time = <50>;
ti,clock-cycles = <16>;
reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>,
<0x4a0021a4 0x8>, <0x4ae0c314 0x4>;
reg-names = "base-address", "int-address",
"efuse-address", "ldo-address";
ti,tranxdone-status-mask = <0x80000000>;
/* LDOVBBMM_MUX_CTRL */
ti,ldovbb-override-mask = <0x400>;
/* LDOVBBMM_VSET_OUT */
ti,ldovbb-vset-mask = <0x1F>;
/*
* NOTE: only FBB mode used but actual vset will
* determine final biasing
*/
ti,abb_info = <
/*uV ABB efuse rbb_m fbb_m vset_m*/
1025000 0 0x0 0 0x02000000 0x01F00000
1120000 0 0x4 0 0x02000000 0x01F00000
>;
};
};
};
&cpu_thermal {
polling-delay = <500>; /* milliseconds */
coefficients = <65 (-1791)>;
};
#include "omap5-l4.dtsi"
#include "omap54xx-clocks.dtsi"
&gpu_thermal {
coefficients = <117 (-2992)>;
};
&core_thermal {
coefficients = <0 2000>;
};
#include "omap5-l4-abe.dtsi"
#include "omap54xx-clocks.dtsi"