/*
* Copyright (C) 2004 Red Hat
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
*
* May be copied or modified under the terms of the GNU General Public License
* Based in part on the ITE vendor provided SCSI driver.
*
* Documentation:
* Datasheet is freely available, some other documents under NDA.
*
* The ITE8212 isn't exactly a standard IDE controller. It has two
* modes. In pass through mode then it is an IDE controller. In its smart
* mode its actually quite a capable hardware raid controller disguised
* as an IDE controller. Smart mode only understands DMA read/write and
* identify, none of the fancier commands apply. The IT8211 is identical
* in other respects but lacks the raid mode.
*
* Errata:
* o Rev 0x10 also requires master/slave hold the same DMA timings and
* cannot do ATAPI MWDMA.
* o The identify data for raid volumes lacks CHS info (technically ok)
* but also fails to set the LBA28 and other bits. We fix these in
* the IDE probe quirk code.
* o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
* raid then the controller firmware dies
* o Smart mode without RAID doesn't clear all the necessary identify
* bits to reduce the command set to the one used
*
* This has a few impacts on the driver
* - In pass through mode we do all the work you would expect
* - In smart mode the clocking set up is done by the controller generally
* but we must watch the other limits and filter.
* - There are a few extra vendor commands that actually talk to the
* controller but only work PIO with no IRQ.
*
* Vendor areas of the identify block in smart mode are used for the
* timing and policy set up. Each HDD in raid mode also has a serial
* block on the disk. The hardware extra commands are get/set chip status,
* rebuild, get rebuild status.
*
* In Linux the driver supports pass through mode as if the device was
* just another IDE controller. If the smart mode is running then
* volumes are managed by the controller firmware and each IDE "disk"
* is a raid volume. Even more cute - the controller can do automated
* hotplug and rebuild.
*
* The pass through controller itself is a little demented. It has a
* flaw that it has a single set of PIO/MWDMA timings per channel so
* non UDMA devices restrict each others performance. It also has a
* single clock source per channel so mixed UDMA100/133 performance
* isn't perfect and we have to pick a clock. Thankfully none of this
* matters in smart mode. ATAPI DMA is not currently supported.
*
* It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
*
* TODO
* - ATAPI UDMA is ok but not MWDMA it seems
* - RAID configuration ioctls
* - Move to libata once it grows up
*/
#include <linux/types.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/ide.h>
#include <linux/init.h>
#define DRV_NAME "it821x"
#define QUIRK_VORTEX86 1
struct it821x_dev
{
unsigned int smart:1, /* Are we in smart raid mode */
timing10:1; /* Rev 0x10 */
u8 clock_mode; /* 0, ATA_50 or ATA_66 */
u8 want[2][2]; /* Mode/Pri log for master slave */
/* We need these for switching the clock when DMA goes on/off
The high byte is the 66Mhz timing */
u16 pio[2]; /* Cached PIO values */
u16 mwdma[2]; /* Cached MWDMA values */
u16 udma[2]; /* Cached UDMA values (per drive) */
u16 quirks;
};
#define ATA_66 0
#define ATA_50 1
#define ATA_ANY 2
#define UDMA_OFF 0
#define MWDMA_OFF 0
/*
* We allow users to force the card into non raid mode without
* flashing the alternative BIOS. This is also necessary right now
* for embedded platforms that cannot run a PC BIOS but are using this
* device.
*/
static int it8212_noraid;
/**
* it821x_program - program the PIO/MWDMA registers
* @drive: drive to tune
* @timing: timing info
*
* Program the PIO/MWDMA timing for this channel according to the
* current clock.
*/
static void it821x_program(ide_drive_t *drive, u16 timing)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
int channel = hwif->channel;
u8 conf;
/* Program PIO/MWDMA timing bits */
if(itdev->clock_mode == ATA_66)
conf = timing >> 8;
else
conf = timing & 0xFF;
pci_write_config_byte(dev, 0x54 + 4 * channel, conf);
}
/**
* it821x_program_udma - program the UDMA registers
* @drive: drive to tune
* @timing: timing info
*
* Program the UDMA timing for this drive according to the
* current clock.
*/
static void it821x_program_udma(ide_drive_t *drive, u16 timing)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
int channel = hwif->channel;
u8 unit = drive->dn & 1, conf;
/* Program UDMA timing bits */
if(itdev->clock_mode == ATA_66)
conf = timing >> 8;
else
conf = timing & 0xFF;
if (itdev->timing10 == 0)
pci_write_config_byte(dev, 0x56 + 4 * channel + unit, conf);
else {
pci_write_config_byte(dev, 0x56 + 4 * channel, conf);
pci_write_config_byte(dev, 0x56 + 4 * channel + 1, conf);
}
}
/**
* it821x_clock_strategy
* @drive: drive to set up
*
* Select between the 50 and 66Mhz base clocks to get the best
* results for this interface.
*/
static void it821x_clock_strategy(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
ide_drive_t *pair = ide_get_pair_dev(drive);
int clock, altclock, sel = 0;
u8 unit = drive->dn & 1, v;
if(itdev->want[0][0] > itdev->want[1][0]) {
clock = itdev->want[0][1];
altclock = itdev->want[1][1];
} else {
clock = itdev->want[1][1];
altclock = itdev->want[0][1];
}
/*
* if both clocks can be used for the mode with the higher priority
* use the clock needed by the mode with the lower priority
*/
if (clock == ATA_ANY)
clock = altclock;
/* Nobody cares - keep the same clock */
if(clock == ATA_ANY)
return;
/* No change */
if(clock == itdev->clock_mode)
return;
/* Load this into the controller ? */
if(clock == ATA_66)
itdev->clock_mode = ATA_66;
else {
itdev->clock_mode = ATA_50;
sel = 1;
}
pci_read_config_byte(dev, 0x50, &v);
v &= ~(1 << (1 + hwif->channel));
v |= sel << (1 + hwif->channel);
pci_write_config_byte(dev, 0x50, v);
/*
* Reprogram the UDMA/PIO of the pair drive for the switch
* MWDMA will be dealt with by the dma switcher
*/
if(pair && itdev->udma[1-unit] != UDMA_OFF) {
it821x_program_udma(pair, itdev->udma[1-unit]);
it821x_program(pair, itdev->pio[1-unit]);
}
/*
* Reprogram the UDMA/PIO of our drive for the switch.
* MWDMA will be dealt with by the dma switcher
*/
if(itdev->udma[unit] != UDMA_OFF) {
it821x_program_udma(drive, itdev->udma[unit]);
it821x_program(drive, itdev->pio[unit]);
}
}
/**
* it821x_set_pio_mode - set host controller for PIO mode
* @hwif: port
* @drive: drive
*
* Tune the host to the desired PIO mode taking into the consideration
* the maximum PIO mode supported by the other device on the cable.
*/
static void it821x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
ide_drive_t *pair = ide_get_pair_dev(drive);
const u8 pio = drive->pio_mode - XFER_PIO_0;
u8 unit = drive->dn & 1, set_pio = pio;
/* Spec says 89 ref driver uses 88 */
static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
/*
* Compute the best PIO mode we can for a given device. We must
* pick a speed that does not cause problems with the other device
* on the cable.
*/
if (pair) {
u8 pair_pio = pair->pio_mode - XFER_PIO_0;
/* trim PIO to the slowest of the master/slave */
if (pair_pio < set_pio)
set_pio = pair_pio;
}
/* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
itdev->want[unit][1] = pio_want[set_pio];
itdev->want[unit][0] = 1; /* PIO is lowest priority */
itdev->pio[unit] = pio_timings[set_pio];
it821x_clock_strategy(drive);
it821x_program(drive, itdev->pio[unit]);
}
/**
* it821x_tune_mwdma - tune a channel for MWDMA
* @drive: drive to set up
* @mode_wanted: the target operating mode
*
* Load the timing settings for this device mode into the
* controller when doing MWDMA in pass through mode. The caller
* must manage the whole lack of per device MWDMA/PIO timings and
* the shared MWDMA/PIO timing register.
*/
static void it821x_tune_mwdma(ide_drive_t *drive, u8 mode_wanted)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif);
u8 unit = drive->dn & 1, channel = hwif->channel, conf;
static u16 dma[] = { 0x8866, 0x3222, 0x3121 };
static u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY };
itdev->want[unit][1] = mwdma_want[mode_wanted];
itdev->want[unit][0] = 2; /* MWDMA is low priority */
itdev->mwdma[unit] = dma[mode_wanted];
itdev->udma[unit] = UDMA_OFF;
/* UDMA bits off - Revision 0x10 do them in pairs */
pci_read_config_byte(dev, 0x50, &conf);
if (itdev->timing10)
conf |= channel ? 0x60: 0x18;
else
conf |= 1 << (3 + 2 * channel + unit);
pci_write_config_byte(dev, 0x50, conf);
it821x_clock_strategy(drive);
/* FIXME: do we need to program this ? */
/* it821x_program(drive, itdev->mwdma[unit]); */
}
/**
* it821x_tune_udma - tune a channel for UDMA
* @drive: drive to set up
* @mode_wanted: the target operating mode
*
* Load the timing settings for this device mode into the
* controller when doing UDMA modes in pass through.
*/
static void it821x_tune_udma(ide_drive_t *drive, u8 mode_wanted)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
u8 unit = drive->dn & 1, channel = hwif->channel, conf;
static u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
static u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
itdev->want[unit][1] = udma_want[mode_wanted];
itdev->want[unit][0] = 3; /* UDMA is high priority */
itdev->mwdma[unit] = MWDMA_OFF;
itdev->udma[unit] = udma[mode_wanted];
if(mode_wanted >= 5)
itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */
/* UDMA on. Again revision 0x10 must do the pair */
pci_read_config_byte(dev, 0x50, &conf);
if (itdev->timing10)
conf &= channel ? 0x9F: 0xE7;
else
conf &= ~ (1 << (3 + 2 * channel + unit));
pci_write_config_byte(dev, 0x50, conf);
it821x_clock_strategy(drive);
it821x_program_udma(drive, itdev->udma[unit]);
}
/**
* it821x_dma_read - DMA hook
* @drive: drive for DMA
*
* The IT821x has a single timing register for MWDMA and for PIO
* operations. As we flip back and forth we have to reload the
* clock. In addition the rev 0x10 device only works if the same
* timing value is loaded into the master and slave UDMA clock
* so we must also reload that.
*
* FIXME: we could figure out in advance if we need to do reloads
*/
static void it821x_dma_start(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
u8 unit = drive->dn & 1;
if(itdev->mwdma[unit] != MWDMA_OFF)
it821x_program(drive, itdev->mwdma[unit]);
else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10)
it821x_program_udma(drive, itdev->udma[unit]);
ide_dma_start(drive);
}
/**
* it821x_dma_write - DMA hook
* @drive: drive for DMA stop
*
* The IT821x has a single timing register for MWDMA and for PIO
* operations. As we flip back and forth we have to reload the
* clock.
*/
static int it821x_dma_end(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
int ret = ide_dma_end(drive);
u8 unit = drive->dn & 1;
if(itdev->mwdma[unit] != MWDMA_OFF)
it821x_program(drive, itdev->pio[unit]);
return ret;
}
/**
* it821x_set_dma_mode - set host controller for DMA mode
* @hwif: port
* @drive: drive
*
* Tune the ITE chipset for the desired DMA mode.
*/
static void it821x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
const u8 speed = drive->dma_mode;
/*
* MWDMA tuning is really hard because our MWDMA and PIO
* timings are kept in the same place. We can switch in the
* host dma on/off callbacks.
*/
if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6)
it821x_tune_udma(drive, speed - XFER_UDMA_0);
else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0);
}
/**
* it821x_cable_detect - cable detection
* @hwif: interface to check
*
* Check for the presence of an ATA66 capable cable on the
* interface. Problematic as it seems some cards don't have
* the needed logic onboard.
*/
static u8 it821x_cable_detect(ide_hwif_t *hwif)
{
/* The reference driver also only does disk side */
return ATA_CBL_PATA80;
}
/**
* it821x_quirkproc - post init callback
* @drive: drive
*
* This callback is run after the drive has been probed but
* before anything gets attached. It allows drivers to do any
* final tuning that is needed, or fixups to work around bugs.
*/
static void it821x_quirkproc(ide_drive_t *drive)
{
struct it821x_dev *itdev = ide_get_hwifdata(drive->hwif);
u16 *id = drive->id;
if (!itdev->smart) {
/*
* If we are in pass through mode then not much
* needs to be done, but we do bother to clear the
* IRQ mask as we may well be in PIO (eg rev 0x10)
* for now and we know unmasking is safe on this chipset.
*/
drive->dev_flags |= IDE_DFLAG_UNMASK;
} else {
/*
* Perform fixups on smart mode. We need to "lose" some
* capabilities the firmware lacks but does not filter, and
* also patch up some capability bits that it forgets to set
* in RAID mode.
*/
/* Check for RAID v native */
if (strstr((char *)&id[ATA_ID_PROD],
"Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id[ATA_ID_CAPABILITY] |= (3 << 8); /* LBA28, DMA */
id[ATA_ID_COMMAND_SET_2] |= 0x0400; /* LBA48 valid */
id[ATA_ID_CFS_ENABLE_2] |= 0x0400; /* LBA48 on */
/* Reporting logic */
printk(KERN_INFO "%s: IT8212 %sRAID %d volume",
drive->name, id[147] ? "Bootable " : "",
id[ATA_ID_CSFO]);
if (id[ATA_ID_CSFO] != 1)
printk(KERN_CONT "(%dK stripe)", id[146]);
printk(KERN_CONT ".\n");
} else {
/* Non RAID volume. Fixups to stop the core code
doing unsupported things */
id[ATA_ID_FIELD_VALID] &= 3;
id[ATA_ID_QUEUE_DEPTH] = 0;
id[ATA_ID_COMMAND_SET_1] = 0;
id[ATA_ID_COMMAND_SET_2] &= 0xC400;
id[ATA_ID_CFSSE] &= 0xC000;
id[ATA_ID_CFS_ENABLE_1] = 0;
id[ATA_ID_CFS_ENABLE_2] &= 0xC400;
id[ATA_ID_CSF_DEFAULT] &= 0xC000;
id[127] = 0;
id[ATA_ID_DLF] = 0;
id[ATA_ID_CSFO] = 0;
id[ATA_ID_CFA_POWER] = 0;
printk(KERN_INFO "%s: Performing identify fixups.\n",
drive->name);
}
/*
* Set MWDMA0 mode as enabled/support - just to tell
* IDE core that DMA is supported (it821x hardware
* takes care of DMA mode programming).
*/
if (ata_id_has_dma(id)) {
id[ATA_ID_MWDMA_MODES] |= 0x0101;
drive->current_speed = XFER_MW_DMA_0;
}
}
}
static const struct ide_dma_ops it821x_pass_through_dma_ops = {
.dma_host_set = ide_dma_host_set,
.dma_setup = ide_dma_setup,
.dma_start = it821x_dma_start,
.dma_end = it821x_dma_end,
.dma_test_irq = ide_dma_test_irq,
.dma_lost_irq = ide_dma_lost_irq,
.dma_timer_expiry = ide_dma_sff_timer_expiry,
.dma_sff_read_status = ide_dma_sff_read_status,
};
/**
* init_hwif_it821x - set up hwif structs
* @hwif: interface to set up
*
* We do the basic set up of the interface structure. The IT8212
* requires several custom handlers so we override the default
* ide DMA handlers appropriately
*/
static void init_hwif_it821x(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct ide_host *host = pci_get_drvdata(dev);
struct it821x_dev *itdevs = host->host_priv;
struct it821x_dev *idev = itdevs + hwif->channel;
u8 conf;
ide_set_hwifdata(hwif, idev);
pci_read_config_byte(dev, 0x50, &conf);
if (conf & 1) {
idev->smart = 1;
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
/* Long I/O's although allowed in LBA48 space cause the
onboard firmware to enter the twighlight zone */
hwif->rqsize = 256;
}
/* Pull the current clocks from 0x50 also */
if (conf & (1 << (1 + hwif->channel)))
idev->clock_mode = ATA_50;
else
idev->clock_mode = ATA_66;
idev->want[0][1] = ATA_ANY;
idev->want[1][1] = ATA_ANY;
/*
* Not in the docs but according to the reference driver
* this is necessary.
*/
if (dev->revision == 0x10) {
idev->timing10 = 1;
hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
if (idev->smart == 0)
printk(KERN_WARNING DRV_NAME " %s: revision 0x10, "
"workarounds activated\n", pci_name(dev));
}
if (idev->smart == 0) {
/* MWDMA/PIO clock switching for pass through mode */
hwif->dma_ops = &it821x_pass_through_dma_ops;
} else
hwif->host_flags |= IDE_HFLAG_NO_SET_MODE;
if (hwif->dma_base == 0)
return;
hwif->ultra_mask = ATA_UDMA6;
hwif->mwdma_mask = ATA_MWDMA2;
/* Vortex86SX quirk: prevent Ultra-DMA mode to fix BadCRC issue */
if (idev->quirks & QUIRK_VORTEX86) {
if (dev->revision == 0x11)
hwif->ultra_mask = 0;
}
}
static void it8212_disable_raid(struct pci_dev *dev)
{
/* Reset local CPU, and set BIOS not ready */
pci_write_config_byte(dev, 0x5E, 0x01);
/* Set to bypass mode, and reset PCI bus */
pci_write_config_byte(dev, 0x50, 0x00);
pci_write_config_word(dev, PCI_COMMAND,
PCI_COMMAND_PARITY | PCI_COMMAND_IO |
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
pci_write_config_word(dev, 0x40, 0xA0F3);
pci_write_config_dword(dev,0x4C, 0x02040204);
pci_write_config_byte(dev, 0x42, 0x36);
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
}
static int init_chipset_it821x(struct pci_dev *dev)
{
u8 conf;
static char *mode[2] = { "pass through", "smart" };
/* Force the card into bypass mode if so requested */
if (it8212_noraid) {
printk(KERN_INFO DRV_NAME " %s: forcing bypass mode\n",
pci_name(dev));
it8212_disable_raid(dev);
}
pci_read_config_byte(dev, 0x50, &conf);
printk(KERN_INFO DRV_NAME " %s: controller in %s mode\n",
pci_name(dev), mode[conf & 1]);
return 0;
}
static const struct ide_port_ops it821x_port_ops = {
/* it821x_set_{pio,dma}_mode() are only used in pass-through mode */
.set_pio_mode = it821x_set_pio_mode,
.set_dma_mode = it821x_set_dma_mode,
.quirkproc = it821x_quirkproc,
.cable_detect = it821x_cable_detect,
};
static const struct ide_port_info it821x_chipset = {
.name = DRV_NAME,
.init_chipset = init_chipset_it821x,
.init_hwif = init_hwif_it821x,
.port_ops = &it821x_port_ops,
.pio_mask = ATA_PIO4,
};
/**
* it821x_init_one - pci layer discovery entry
* @dev: PCI device
* @id: ident table entry
*
* Called by the PCI code when it finds an ITE821x controller.
* We then use the IDE PCI generic helper to do most of the work.
*/
static int it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct it821x_dev *itdevs;
int rc;
itdevs = kcalloc(2, sizeof(*itdevs), GFP_KERNEL);
if (itdevs == NULL) {
printk(KERN_ERR DRV_NAME " %s: out of memory\n", pci_name(dev));
return -ENOMEM;
}
itdevs->quirks = id->driver_data;
rc = ide_pci_init_one(dev, &it821x_chipset, itdevs);
if (rc)
kfree(itdevs);
return rc;
}
static void it821x_remove(struct pci_dev *dev)
{
struct ide_host *host = pci_get_drvdata(dev);
struct it821x_dev *itdevs = host->host_priv;
ide_pci_remove(dev);
kfree(itdevs);
}
static const struct pci_device_id it821x_pci_tbl[] = {
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), 0 },
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), 0 },
{ PCI_VDEVICE(RDC, PCI_DEVICE_ID_RDC_D1010), QUIRK_VORTEX86 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, it821x_pci_tbl);
static struct pci_driver it821x_pci_driver = {
.name = "ITE821x IDE",
.id_table = it821x_pci_tbl,
.probe = it821x_init_one,
.remove = it821x_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init it821x_ide_init(void)
{
return ide_pci_register_driver(&it821x_pci_driver);
}
static void __exit it821x_ide_exit(void)
{
pci_unregister_driver(&it821x_pci_driver);
}
module_init(it821x_ide_init);
module_exit(it821x_ide_exit);
module_param_named(noraid, it8212_noraid, int, S_IRUGO);
MODULE_PARM_DESC(noraid, "Force card into bypass mode");
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("PCI driver module for the ITE 821x");
MODULE_LICENSE("GPL");