# SPDX-License-Identifier: GPL-2.0-only # 64-bit [31mCONFIG_ARM[0m SoCs from TI if [31mCONFIG_ARM64[0m if [31mCONFIG_ARCH_K3[0m config [31mCONFIG_ARCH_K3_AM6_SOC[0m bool "K3 AM6 SoC" help Enable support for TI's AM6 SoC Family support config [31mCONFIG_ARCH_K3_J721E_SOC[0m bool "K3 J721E SoC" help Enable support for TI's J721E SoC Family support endif endif # # TI SOC drivers # menuconfig [31mCONFIG_SOC_TI[0m bool "TI SOC drivers support" if [31mCONFIG_SOC_TI[0m config [31mCONFIG_KEYSTONE_NAVIGATOR_QMSS[0m tristate "Keystone Queue Manager Sub System" depends on [31mCONFIG_ARCH_KEYSTONE[0m help Say y here to support the Keystone multicore Navigator Queue Manager support. The Queue Manager is a hardware module that is responsible for accelerating management of the packet queues. Packets are queued/de-queued by writing/reading descriptor address to a particular memory mapped location in the Queue Manager module. If unsure, say N. config [31mCONFIG_KEYSTONE_NAVIGATOR_DMA[0m tristate "TI Keystone Navigator Packet DMA support" depends on [31mCONFIG_ARCH_KEYSTONE[0m help Say y tp enable support for the Keystone Navigator Packet DMA on on Keystone family of devices. It sets up the dma channels for the Queue Manager Sub System. If unsure, say N. config [31mCONFIG_AMX3_PM[0m tristate "AMx3 Power Management" depends on [31mCONFIG_SOC_AM33XX[0m || [31mCONFIG_SOC_AM43XX[0m depends on [31mCONFIG_WKUP_M3_IPC[0m && [31mCONFIG_TI_EMIF_SRAM[0m && [31mCONFIG_SRAM[0m && [31mCONFIG_RTC_DRV_OMAP[0m help Enable power management on AM335x and AM437x. Required for suspend to mem and standby states on both AM335x and AM437x platforms and for deeper cpuidle c-states on AM335x. Also required for rtc and ddr in self-refresh low power mode on AM437x platforms. config [31mCONFIG_WKUP_M3_IPC[0m tristate "TI AMx3 Wkup-M3 IPC Driver" depends on [31mCONFIG_WKUP_M3_RPROC[0m depends on [31mCONFIG_OMAP2PLUS_MBOX[0m help TI AM33XX and AM43XX have a Cortex M3, the Wakeup M3, to handle low power transitions. This IPC driver provides the necessary API to communicate and use the Wakeup M3 for [31mCONFIG_PM[0m features like suspend resume and boots it using wkup_m3_rproc driver. config [31mCONFIG_TI_SCI_PM_DOMAINS[0m tristate "TI SCI PM Domains Driver" depends on [31mCONFIG_TI_SCI_PROTOCOL[0m depends on [31mCONFIG_PM_GENERIC_DOMAINS[0m help Generic power domain implementation for TI device implementing the TI SCI protocol. To compile this as a module, choose [31mCONFIG_M[0m here. The module will be called ti_sci_pm_domains. Note this is needed early in boot before rootfs may be available. endif # [31mCONFIG_SOC_TI[0m config [31mCONFIG_TI_SCI_INTA_MSI_DOMAIN[0m bool select [31mCONFIG_GENERIC_MSI_IRQ_DOMAIN[0m help Driver to enable Interrupt Aggregator specific MSI Domain. |