// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2019, Linaro Ltd.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sdm845.dtsi"
#include "pm8998.dtsi"
#include "pmi8998.dtsi"
/ {
model = "Thundercomm Dragonboard 845c";
compatible = "thundercomm,db845c", "qcom,sdm845";
aliases {
serial0 = &uart9;
hsuart0 = &uart6;
};
chosen {
stdout-path = "serial0:115200n8";
};
dc12v: dc12v-regulator {
compatible = "regulator-fixed";
regulator-name = "DC12V";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
regulator-always-on;
};
gpio_keys {
compatible = "gpio-keys";
autorepeat;
pinctrl-names = "default";
pinctrl-0 = <&vol_up_pin_a>;
vol-up {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
user4 {
label = "green:user4";
gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "panic-indicator";
default-state = "off";
};
wlan {
label = "yellow:wlan";
gpios = <&pm8998_gpio 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tx";
default-state = "off";
};
bt {
label = "blue:bt";
gpios = <&pm8998_gpio 5 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bluetooth-power";
default-state = "off";
};
};
lt9611_1v8: lt9611-vdd18-regulator {
compatible = "regulator-fixed";
regulator-name = "LT9611_1V8";
vin-supply = <&vdc_5v>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
lt9611_3v3: lt9611-3v3 {
compatible = "regulator-fixed";
regulator-name = "LT9611_3V3";
vin-supply = <&vdc_3v3>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
// TODO: make it possible to drive same GPIO from two clients
// gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
// enable-active-high;
};
pcie0_1p05v: pcie-0-1p05v-regulator {
compatible = "regulator-fixed";
regulator-name = "PCIE0_1.05V";
vin-supply = <&vbat>;
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
// TODO: make it possible to drive same GPIO from two clients
// gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
// enable-active-high;
};
pcie0_3p3v_dual: vldo-3v3-regulator {
compatible = "regulator-fixed";
regulator-name = "VLDO_3V3";
vin-supply = <&vbat>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&pcie0_pwren_state>;
};
v5p0_hdmiout: v5p0-hdmiout-regulator {
compatible = "regulator-fixed";
regulator-name = "V5P0_HDMIOUT";
vin-supply = <&vdc_5v>;
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <500000>;
// TODO: make it possible to drive same GPIO from two clients
// gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
// enable-active-high;
};
vbat: vbat-regulator {
compatible = "regulator-fixed";
regulator-name = "VBAT";
vin-supply = <&dc12v>;
regulator-min-microvolt = <4200000>;
regulator-max-microvolt = <4200000>;
regulator-always-on;
};
vbat_som: vbat-som-regulator {
compatible = "regulator-fixed";
regulator-name = "VBAT_SOM";
vin-supply = <&dc12v>;
regulator-min-microvolt = <4200000>;
regulator-max-microvolt = <4200000>;
regulator-always-on;
};
vdc_3v3: vdc-3v3-regulator {
compatible = "regulator-fixed";
regulator-name = "VDC_3V3";
vin-supply = <&dc12v>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdc_5v: vdc-5v-regulator {
compatible = "regulator-fixed";
regulator-name = "VDC_5V";
vin-supply = <&dc12v>;
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <500000>;
regulator-always-on;
};
vreg_s4a_1p8: vreg-s4a-1p8 {
compatible = "regulator-fixed";
regulator-name = "vreg_s4a_1p8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
vin-supply = <&vbat_som>;
};
};
&adsp_pas {
status = "okay";
firmware-name = "qcom/db845c/adsp.mdt";
};
&apps_rsc {
pm8998-rpmh-regulators {
compatible = "qcom,pm8998-rpmh-regulators";
qcom,pmic-id = "a";
vdd-s1-supply = <&vph_pwr>;
vdd-s2-supply = <&vph_pwr>;
vdd-s3-supply = <&vph_pwr>;
vdd-s4-supply = <&vph_pwr>;
vdd-s5-supply = <&vph_pwr>;
vdd-s6-supply = <&vph_pwr>;
vdd-s7-supply = <&vph_pwr>;
vdd-s8-supply = <&vph_pwr>;
vdd-s9-supply = <&vph_pwr>;
vdd-s10-supply = <&vph_pwr>;
vdd-s11-supply = <&vph_pwr>;
vdd-s12-supply = <&vph_pwr>;
vdd-s13-supply = <&vph_pwr>;
vdd-l1-l27-supply = <&vreg_s7a_1p025>;
vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
vdd-l3-l11-supply = <&vreg_s7a_1p025>;
vdd-l4-l5-supply = <&vreg_s7a_1p025>;
vdd-l6-supply = <&vph_pwr>;
vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
vdd-l9-supply = <&vreg_bob>;
vdd-l10-l23-l25-supply = <&vreg_bob>;
vdd-l13-l19-l21-supply = <&vreg_bob>;
vdd-l16-l28-supply = <&vreg_bob>;
vdd-l18-l22-supply = <&vreg_bob>;
vdd-l20-l24-supply = <&vreg_bob>;
vdd-l26-supply = <&vreg_s3a_1p35>;
vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
vreg_s3a_1p35: smps3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
vreg_s5a_2p04: smps5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
vreg_s7a_1p025: smps7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
vreg_l1a_0p875: ldo1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l5a_0p8: ldo5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l12a_1p8: ldo12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l7a_1p8: ldo7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l13a_2p95: ldo13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l17a_1p3: ldo17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l20a_2p95: ldo20 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2968000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l21a_2p95: ldo21 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2968000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l24a_3p075: ldo24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l25a_3p3: ldo25 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3312000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l26a_1p2: ldo26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
};
pmi8998-rpmh-regulators {
compatible = "qcom,pmi8998-rpmh-regulators";
qcom,pmic-id = "b";
vdd-bob-supply = <&vph_pwr>;
vreg_bob: bob {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3600000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
regulator-allow-bypass;
};
};
};
&cdsp_pas {
status = "okay";
firmware-name = "qcom/db845c/cdsp.mdt";
};
&gcc {
protected-clocks = <GCC_QSPI_CORE_CLK>,
<GCC_QSPI_CORE_CLK_SRC>,
<GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
};
&pm8998_gpio {
vol_up_pin_a: vol-up-active {
pins = "gpio6";
function = "normal";
input-enable;
bias-pull-up;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
};
&pm8998_pon {
resin {
compatible = "qcom,pm8941-resin";
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
linux,code = <KEY_VOLUMEDOWN>;
};
};
&qupv3_id_0 {
status = "okay";
};
&qupv3_id_1 {
status = "okay";
};
&sdhc_2 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
vmmc-supply = <&vreg_l21a_2p95>;
vqmmc-supply = <&vreg_l13a_2p95>;
bus-width = <4>;
cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
};
&tlmm {
pcie0_pwren_state: pcie0-pwren {
pins = "gpio90";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
sdc2_default_state: sdc2-default {
clk {
pins = "sdc2_clk";
bias-disable;
/*
* It seems that mmc_test reports errors if drive
* strength is not 16 on clk, cmd, and data pins.
*/
drive-strength = <16>;
};
cmd {
pins = "sdc2_cmd";
bias-pull-up;
drive-strength = <10>;
};
data {
pins = "sdc2_data";
bias-pull-up;
drive-strength = <10>;
};
};
sdc2_card_det_n: sd-card-det-n {
pins = "gpio126";
function = "gpio";
bias-pull-up;
};
};
&uart6 {
status = "okay";
bluetooth {
compatible = "qcom,wcn3990-bt";
vddio-supply = <&vreg_s4a_1p8>;
vddxo-supply = <&vreg_l7a_1p8>;
vddrf-supply = <&vreg_l17a_1p3>;
vddch0-supply = <&vreg_l25a_3p3>;
max-speed = <3200000>;
};
};
&uart9 {
status = "okay";
};
&usb_1 {
status = "okay";
};
&usb_1_dwc3 {
dr_mode = "peripheral";
};
&usb_1_hsphy {
status = "okay";
vdd-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l12a_1p8>;
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
qcom,imp-res-offset-value = <8>;
qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
};
&usb_1_qmpphy {
status = "okay";
vdda-phy-supply = <&vreg_l26a_1p2>;
vdda-pll-supply = <&vreg_l1a_0p875>;
};
&usb_2 {
status = "okay";
};
&usb_2_dwc3 {
dr_mode = "host";
};
&usb_2_hsphy {
status = "okay";
vdd-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l12a_1p8>;
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
qcom,imp-res-offset-value = <8>;
qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
};
&usb_2_qmpphy {
status = "okay";
vdda-phy-supply = <&vreg_l26a_1p2>;
vdda-pll-supply = <&vreg_l1a_0p875>;
};
&ufs_mem_hc {
status = "okay";
reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
vcc-supply = <&vreg_l20a_2p95>;
vcc-max-microamp = <800000>;
};
&ufs_mem_phy {
status = "okay";
vdda-phy-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l26a_1p2>;
};
&wifi {
status = "okay";
vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
};
/* PINCTRL - additions to nodes defined in sdm845.dtsi */
&qup_uart6_default {
pinmux {
pins = "gpio45", "gpio46", "gpio47", "gpio48";
function = "qup6";
};
cts {
pins = "gpio45";
bias-disable;
};
rts-tx {
pins = "gpio46", "gpio47";
drive-strength = <2>;
bias-disable;
};
rx {
pins = "gpio48";
bias-pull-up;
};
};
&qup_uart9_default {
pinconf-tx {
pins = "gpio4";
drive-strength = <2>;
bias-disable;
};
pinconf-rx {
pins = "gpio5";
drive-strength = <2>;
bias-pull-up;
};
};