/* $NetBSD: ka43.h,v 1.8 2017/05/22 17:12:11 ragge Exp $ */
/*
* Copyright (c) 1996 Ludd, University of Lule}, Sweden.
* All rights reserved.
*
* This code is derived from software contributed to Ludd by Bertram Barth.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef _VAX_KA43_H_
#define _VAX_KA43_H_
/*
* Definitions for I/O addresses of
*
* VAXstation 3100 model 76 (RigelMAX)
*/
#define KA43_SIDEX 0x20040004 /* SID extension register */
#define KA43_CFGTST 0x20020000 /* Configuration and Test register */
#define KA43_IORESET 0x20020000 /* I/O Reset register */
#define KA43_ROMGETC 0x20040044
#define KA43_ROMPUTC 0x20040058
#define KA43_ROMPUTS 0x2004004C
#define KA43_CH2_BASE 0x10000000 /* 2nd level cache data area */
#define KA43_CH2_END 0x1FFFFFFF
#define KA43_CH2_SIZE 0x10000000
#define KA43_CT2_BASE 0x21000000 /* 2nd level cache tag area */
#define KA43_CT2_END 0x2101FFFF
#define KA43_CT2_SIZE 0x20000
#define KA43_CH2_CREG 0x21100000 /* 2nd level cache control register */
#define KA43_ROM_BASE 0x20040000 /* System module ROM */
#define KA43_ROM_END 0x2007FFFF
#define KA43_ROM_SIZE 0x40000 /* ??? */
#define KA43_IVN_BASE 0x20040020 /* Interrupt Vector Numbers */
#define KA43_IVN_END 0x2004003F
#define KA43_IVN_SIZE 0x20
#define KA43_HLTCOD 0x20080000 /* Halt Code Register */
/* #define KA43_MSER 0x20080004*/ /* Memory System Error register */
/* #define KA43_MEAR 0x20080008*/ /* Memory Error Address register */
#define KA43_INTMSK 0x2008000C /* Interrupt Mask register */
#define KA43_VDCORG 0x2008000D /* Video Controller Origin Register */
#define KA43_VDCSEL 0x2008000E /* Video Controller Select Register */
#define KA43_INTREQ 0x2008000F /* Interrupt Request register */
#define KA43_INTCLR 0x2008000F /* Interrupt Request clear register */
#define KA43_DIAGDSP 0x20080010 /* Diagnostic display register */
#define KA43_PARCTL 0x20080014 /* Parity Control Register */
#define KA43_DIAGTME 0x2008001E /* diagnostic time register */
#define KA43_PCTL_DPEN 0x00000001 /* DMA parity enable (bit 0) */
#define KA43_PCTL_CPEN 0x00000002 /* CPU Parity enable (bit 1) */
#define KA43_PCTL_DMA 0x01000000 /* LANCE DMA control (bit 24) */
/*
* "CH2" and "SESR" are two common names related to Secondary Cache
*/
#define KA43_SESR 0x21100000 /* same as KA43_CH2_CREG */
#define KA43_SESR_CENB 0x00000001 /* Cache Enable */
#define KA43_SESR_SERR 0x00000002
#define KA43_SESR_LERR 0x00000004
#define KA43_SESR_CERR 0x00000008
#define KA43_SESR_DIRTY 0x00000010
#define KA43_SESR_MISS 0x00000020
#define KA43_SESR_DPE 0x00000040 /* Dal Parity Error */
#define KA43_SESR_TPE 0x00000080 /* Tag Parity Error */
#define KA43_SESR_WSB 0x00010000
#define KA43_SESR_CIEA 0x7FFC0000
#define KA43_SESR_BITS \
"\020\010TPE\007DPE\006MISS\005DIRTY\004CERR\003LERR\002SERR\001ENABLE"
/*
* The following values refer to bits/bitfields within the 4 internal
* registers controlling primary cache:
* PR_PCTAG(124, tag-register) PR_PCIDX(125, index-register)
* PR_PCERR(126, error-register) PR_PCSTS(127, status-register)
*/
#define KA43_PCTAG_TAG 0x1FFFF800 /* bits 11-29 */
#define KA43_PCTAG_PARITY 0x40000000
#define KA43_PCTAG_VALID 0x80000000
#define KA43_PCIDX_INDEX 0x000007F8 /* 0x100 Q-word entries */
#define KA43_PCERR_ADDR 0x3FFFFFFF
#define KA43_PCS_FORCEHIT 0x00000001 /* Force hit */
#define KA43_PCS_ENABLE 0x00000002 /* Enable primary cache */
#define KA43_PCS_FLUSH 0x00000004 /* Flush cache */
#define KA43_PCS_REFRESH 0x00000008 /* Enable refresh */
#define KA43_PCS_HIT 0x00000010 /* Cache hit */
#define KA43_PCS_INTERRUPT 0x00000020 /* Interrupt pending */
#define KA43_PCS_TRAP2 0x00000040 /* Trap while trap */
#define KA43_PCS_TRAP1 0x00000080 /* Micro trap/machine check */
#define KA43_PCS_TPERR 0x00000100 /* Tag parity error */
#define KA43_PCS_DPERR 0x00000200 /* Dal data parity error */
#define KA43_PCS_PPERR 0x00000400 /* P data parity error */
#define KA43_PCS_BUSERR 0x00000800 /* Bus error */
#define KA43_PCS_BCHIT 0x00001000 /* B cache hit */
#define KA43_PCSTS_BITS \
"\020\015BCHIT\014BUSERR\013PPERR\012DPERR\011TPERR\010TRAP1" \
"\007TRAP2\006INTR\005HIT\004REFRESH\003FLUSH\002ENABLE\001FORCEHIT"
/*
* Bits in PR_ACCS (Floating Point Accelerator Register)
*/
#define KA43_ACCS_VECTOR (1<<0) /* Vector Unit Present */
#define KA43_ACCS_FCHIP (1<<1) /* FPU chip present */
#define KA43_ACCS_WEP (1<<31) /* Write Even Parity */
/*
* Other fixed addresses which should be mapped
*/
#define KA43_CPU_BASE 0x20080000 /* so called "CPU registers" */
#define KA43_CPU_END 0x200800FF
#define KA43_CPU_SIZE 0x100
#define KA43_NWA_BASE 0x20090000 /* Network Address ROM */
#define KA43_NWA_END 0x2009007F
#define KA43_NWA_SIZE 0x80
#define KA43_SER_BASE 0x200A0000 /* Serial line controller */
#define KA43_SER_END 0x200A000F
#define KA43_SER_SIZE 0x10
#define KA43_WAT_BASE 0x200B0000 /* TOY clock and NV-RAM */
#define KA43_WAT_END 0x200B00FF
#define KA43_WAT_SIZE 0x100
#define KA43_SC1_BASE 0x200C0080 /* 1st SCSI Controller Chip */
#define KA43_SC1_END 0x200C009F
#define KA43_SC1_SIZE 0x20
#define KA43_SC2_BASE 0x200C0180 /* 2nd SCSI Controller Chip */
#define KA43_SC2_END 0x200C019F
#define KA43_SC2_SIZE 0x20
#define KA43_SCS_BASE 0x200C0000 /* area occupied by SCSI 1+2 */
#define KA43_SCS_END 0x200C01FF
#define KA43_SCS_SIZE 0x200
#define KA43_LAN_BASE 0x200E0000 /* LANCE chip registers */
#define KA43_LAN_END 0x200E0007
#define KA43_LAN_SIZE 0x08
#define KA43_CUR_BASE 0x200F0000 /* Monochrome video cursor chip */
#define KA43_CUR_END 0x200F003C
#define KA43_CUR_SIZE 0x40
#define KA43_DMA_BASE 0x202D0000 /* 128KB Data Buffer */
#define KA43_DMA_END 0x202EFFFF
#define KA43_DMA_SIZE 0x20000
#define KA43_VME_BASE 0x30000000
#define KA43_VME_END 0x3003FFFF
#define KA43_VME_SIZE 0x40000
#define KA43_DIAGMEM 0x28000000 /* start of diagnostic memory */
#define KA43_SC1_DADR 0x200C00A0 /* (1st SCSI) DMA address register */
#define KA43_SC1_DCNT 0x200C00C0 /* (1st SCSI) DMA byte count reg. */
#define KA43_SC1_DDIR 0x200C00C4 /* (1st SCSI) DMA transfer direction */
#define KA43_SC2_DADR 0x200C01A0
#define KA43_SC2_DCNT 0x200C01C0
#define KA43_SC2_DDIR 0x200C01C4
#define KA43_CUR_CMD 0x200F0000 /* Cursor Command Register */
#define KA43_CUR_XPOS 0x200F0004 /* Cursor X position */
#define KA43_CUR_YPOS 0x200F0008 /* Cursor Y position */
#define KA43_CUR_XMIN1 0x200F000C /* Region 1 left edge */
#define KA43_CUR_XMAX1 0x200F0010 /* Region 1 right edge */
#define KA43_CUR_YMIN1 0x200F0014 /* Region 1 top edge */
#define KA43_CUR_YMAX1 0x200F0018 /* Region 1 bottom edge */
#define KA43_CUR_XMIN2 0x200F002C /* Region 2 left edge */
#define KA43_CUR_XMAX2 0x200F0030 /* Region 2 right edge */
#define KA43_CUR_YMIN2 0x200F0034 /* Region 2 top edge */
#define KA43_CUR_YMAX2 0x200F0038 /* Region 2 bottom edge */
/*
* Clock-Chip data in NVRAM
*/
#define KA43_CPMBX 0x200B0038 /* Console Mailbox (1 byte) */
#define KA43_CPFLG 0x200B003C /* Console Program Flags (1 byte) */
#define KA43_LK201_ID 0x200B0040 /* Keyboard Variation (1 byte) */
#define KA43_CONS_ID 0x200B0044 /* Console Device Type (1 byte) */
#define KA43_SCR 0x200B0048 /* Console Scratch RAM */
#define KA43_TEMP 0x200B0058 /* Used by System Firmware */
#define KA43_BAT_CHK 0x200B0088 /* Battery Check Data */
#define KA43_PASSWD 0x200B0098 /* ??? */
#define KA43_BOOTFLG 0x200B00A8 /* Default Boot Flags (4 bytes) */
#define KA43_SCRLEN 0x200B00B8 /* Number of pages of SCR (1 byte) */
#define KA43_SCSIPORT 0x200B00BC /* Tape Controller Port Data */
#define KA43_RESERVED 0x200B00C0 /* Reserved (16 bytes) */
struct ka43_cpu {
u_long hltcod; /* Halt Code Register */
u_long pad2;
u_long pad3;
u_char intreg[4]; /* Four 1-byte registers */
u_short diagdsp; /* Diagnostic display register */
u_short pad4;
u_long parctl; /* Parity Control Register */
u_short pad5;
u_short pad6;
u_short pad7;
u_short diagtme; /* Diagnostic time register */
};
struct ka43_clock {
u_long :2; u_long sec :8; u_long :22;
u_long :2; u_long secalrm :8; u_long :22;
u_long :2; u_long min :8; u_long :22;
u_long :2; u_long minalrm :8; u_long :22;
u_long :2; u_long hr :8; u_long :22;
u_long :2; u_long hralrm :8; u_long :22;
u_long :2; u_long dayofwk :8; u_long :22;
u_long :2; u_long day :8; u_long :22;
u_long :2; u_long mon :8; u_long :22;
u_long :2; u_long yr :8; u_long :22;
u_long :2; u_long csr0 :8; u_long :22;
u_long :2; u_long csr1 :8; u_long :22;
u_long :2; u_long csr2 :8; u_long :22;
u_long :2; u_long csr3 :8; u_long :22;
u_long :2; u_long req :4;
u_long halt :4; u_long :22;
};
#endif /* _VAX_KA43_H_ */