/* $NetBSD: intersil7170reg.h,v 1.2 2008/04/28 20:23:50 martin Exp $ */
/*-
* Copyright (c) 1996 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Adam Glass.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef _INTERSIL7170REG_H_
#define _INTERSIL7170REG_H_
/*
* Driver support for the intersil7170 used in sun[34]s to provide
* real time clock and time-of-day support.
*
* Derived from: datasheet "ICM7170 a uP-Compatible Real-Time Clock"
* document #301680-005, Dec 85
*
* Note that this device provides both time-of-day and interval timer
* functionality. Both functions use the same control registers. On top
* of that, the command control register is write-only. Currently, this
* driver assumes that the interval timer is to be enabled, and hence
* always sets/restores the INTERSIL_CMD_IENABLE control bit when
* manipulating the TOD.
*/
struct intersil_dt { /* from p. 7 of 10 */
uint8_t dt_csec;
uint8_t dt_hour;
uint8_t dt_min;
uint8_t dt_sec;
uint8_t dt_month;
uint8_t dt_day;
uint8_t dt_year;
uint8_t dt_dow;
};
struct intersil7170 {
struct intersil_dt counters;
struct intersil_dt clk_ram; /* should be ok as both are word aligned */
uint8_t clk_intr_reg;
uint8_t clk_cmd_reg;
};
/* Indices to time-of-day clock registers */
#define INTERSIL_ICSEC 0
#define INTERSIL_IHOUR 1
#define INTERSIL_IMIN 2
#define INTERSIL_ISEC 3
#define INTERSIL_IMON 4
#define INTERSIL_IDAY 5
#define INTERSIL_IYEAR 6
#define INTERSIL_IDOW 7
#define INTERSIL_IINTR 16
#define INTERSIL_ICMD 17
/* bit assignments for command register, p. 6 of 10, write-only */
#define INTERSIL_CMD_FREQ_32K 0x0
#define INTERSIL_CMD_FREQ_1M 0x1
#define INTERSIL_CMD_FREQ_2M 0x2
#define INTERSIL_CMD_FREQ_4M 0x3
#define INTERSIL_CMD_12HR_MODE 0x0
#define INTERSIL_CMD_24HR_MODE 0x4
#define INTERSIL_CMD_STOP 0x0
#define INTERSIL_CMD_RUN 0x8
#define INTERSIL_CMD_IDISABLE 0x0
#define INTERSIL_CMD_IENABLE 0x10
#define INTERSIL_CMD_TEST_MODE 0x20
#define INTERSIL_CMD_NORMAL_MODE 0x0
#define INTERSIL_COMMAND(run, interrupt) \
((run) | (interrupt) | INTERSIL_CMD_FREQ_32K | \
INTERSIL_CMD_24HR_MODE | INTERSIL_CMD_NORMAL_MODE)
/* bit assignments for interrupt register r/w, p 7 of 10 */
#define INTERSIL_INTER_ALARM 0x1 /* r/w */
#define INTERSIL_INTER_CSECONDS 0x2 /* r/w */
#define INTERSIL_INTER_DSECONDS 0x4 /* r/w */
#define INTERSIL_INTER_SECONDS 0x8 /* r/w */
#define INTERSIL_INTER_MINUTES 0x10 /* r/w */
#define INTERSIL_INTER_HOURS 0x20 /* r/w */
#define INTERSIL_INTER_DAYS 0x40 /* r/w */
#define INTERSIL_INTER_PENDING 0x80 /* read-only */
#define INTERSIL_INTER_BITS \
"\20\10PENDING\7DAYS\6HRS\5MIN\4SCDS\3DSEC\2CSEC\1ALARM"
#endif /* _INTERSIL7170REG_H_ */