/* $NetBSD: atapi_wdc.c,v 1.141 2021/10/05 08:01:05 rin Exp $ */
/*
* Copyright (c) 1998, 2001 Manuel Bouyer.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <sys/cdefs.h>
__KERNEL_RCSID(0, "$NetBSD: atapi_wdc.c,v 1.141 2021/10/05 08:01:05 rin Exp $");
#ifndef ATADEBUG
#define ATADEBUG
#endif /* ATADEBUG */
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/file.h>
#include <sys/stat.h>
#include <sys/buf.h>
#include <sys/malloc.h>
#include <sys/device.h>
#include <sys/syslog.h>
#include <sys/proc.h>
#include <sys/dvdio.h>
#include <sys/intr.h>
#include <sys/bus.h>
#ifndef __BUS_SPACE_HAS_STREAM_METHODS
#define bus_space_write_multi_stream_2 bus_space_write_multi_2
#define bus_space_write_multi_stream_4 bus_space_write_multi_4
#define bus_space_read_multi_stream_2 bus_space_read_multi_2
#define bus_space_read_multi_stream_4 bus_space_read_multi_4
#endif /* __BUS_SPACE_HAS_STREAM_METHODS */
#include <dev/ata/ataconf.h>
#include <dev/ata/atareg.h>
#include <dev/ata/atavar.h>
#include <dev/ic/wdcreg.h>
#include <dev/ic/wdcvar.h>
#include <dev/scsipi/scsi_all.h> /* for SCSI status */
#define DEBUG_INTR 0x01
#define DEBUG_XFERS 0x02
#define DEBUG_STATUS 0x04
#define DEBUG_FUNCS 0x08
#define DEBUG_PROBE 0x10
#ifdef ATADEBUG
#ifndef ATADEBUG_ATAPI_MASK
#define ATADEBUG_ATAPI_MASK 0x0
#endif
int wdcdebug_atapi_mask = ATADEBUG_ATAPI_MASK;
#define ATADEBUG_PRINT(args, level) \
if (wdcdebug_atapi_mask & (level)) \
printf args
#else
#define ATADEBUG_PRINT(args, level)
#endif
#define ATAPI_DELAY 10 /* 10 ms, this is used only before sending a cmd */
#define ATAPI_MODE_DELAY 1000 /* 1s, timeout for SET_FEATYRE cmds */
static int wdc_atapi_get_params(struct scsipi_channel *, int,
struct ataparams *);
static void wdc_atapi_probe_device(struct atapibus_softc *, int);
static void wdc_atapi_minphys (struct buf *bp);
static int wdc_atapi_start(struct ata_channel *,struct ata_xfer *);
static int wdc_atapi_intr(struct ata_channel *, struct ata_xfer *, int);
static void wdc_atapi_kill_xfer(struct ata_channel *,
struct ata_xfer *, int);
static void wdc_atapi_phase_complete(struct ata_xfer *, int);
static int wdc_atapi_poll(struct ata_channel *, struct ata_xfer *);
static void wdc_atapi_done(struct ata_channel *, struct ata_xfer *);
static void wdc_atapi_reset(struct ata_channel *, struct ata_xfer *);
static void wdc_atapi_scsipi_request(struct scsipi_channel *,
scsipi_adapter_req_t, void *);
static void wdc_atapi_kill_pending(struct scsipi_periph *);
static void wdc_atapi_polldsc(void *arg);
#define MAX_SIZE MAXPHYS
static const struct scsipi_bustype wdc_atapi_bustype = {
.bustype_type = SCSIPI_BUSTYPE_ATAPI,
.bustype_cmd = atapi_scsipi_cmd,
.bustype_interpret_sense = atapi_interpret_sense,
.bustype_printaddr = atapi_print_addr,
.bustype_kill_pending = wdc_atapi_kill_pending,
.bustype_async_event_xfer_mode = NULL,
};
void
wdc_atapibus_attach(struct atabus_softc *ata_sc)
{
struct ata_channel *chp = ata_sc->sc_chan;
struct atac_softc *atac = chp->ch_atac;
struct scsipi_adapter *adapt = &atac->atac_atapi_adapter._generic;
struct scsipi_channel *chan = &chp->ch_atapi_channel;
/*
* Fill in the scsipi_adapter.
*/
adapt->adapt_dev = atac->atac_dev;
adapt->adapt_nchannels = atac->atac_nchannels;
adapt->adapt_request = wdc_atapi_scsipi_request;
adapt->adapt_minphys = wdc_atapi_minphys;
if (atac->atac_cap & ATAC_CAP_NOIRQ)
adapt->adapt_flags |= SCSIPI_ADAPT_POLL_ONLY;
atac->atac_atapi_adapter.atapi_probe_device = wdc_atapi_probe_device;
/*
* Fill in the scsipi_channel.
*/
memset(chan, 0, sizeof(*chan));
chan->chan_adapter = adapt;
chan->chan_bustype = &wdc_atapi_bustype;
chan->chan_channel = chp->ch_channel;
chan->chan_flags = SCSIPI_CHAN_OPENINGS;
chan->chan_openings = 1;
chan->chan_max_periph = 1;
chan->chan_ntargets = chp->ch_ndrives;
chan->chan_nluns = 1;
chp->atapibus = config_found(ata_sc->sc_dev, chan, atapiprint,
CFARGS(.iattr = "atapi"));
}
static void
wdc_atapi_minphys(struct buf *bp)
{
if (bp->b_bcount > MAX_SIZE)
bp->b_bcount = MAX_SIZE;
minphys(bp);
}
/*
* Kill off all pending xfers for a periph.
*
* Must be called with adapter lock held
*/
static void
wdc_atapi_kill_pending(struct scsipi_periph *periph)
{
struct atac_softc *atac =
device_private(periph->periph_channel->chan_adapter->adapt_dev);
struct ata_channel *chp =
atac->atac_channels[periph->periph_channel->chan_channel];
ata_kill_pending(&chp->ch_drive[periph->periph_target]);
}
static void
wdc_atapi_kill_xfer(struct ata_channel *chp, struct ata_xfer *xfer, int reason)
{
struct scsipi_xfer *sc_xfer = xfer->c_scsipi;
bool deactivate = true;
/* remove this command from xfer queue */
switch (reason) {
case KILL_GONE_INACTIVE:
deactivate = false;
/* FALLTHROUGH */
case KILL_GONE:
sc_xfer->error = XS_DRIVER_STUFFUP;
break;
case KILL_RESET:
sc_xfer->error = XS_RESET;
break;
default:
printf("wdc_ata_bio_kill_xfer: unknown reason %d\n",
reason);
panic("wdc_ata_bio_kill_xfer");
}
if (deactivate)
ata_deactivate_xfer(chp, xfer);
ata_free_xfer(chp, xfer);
scsipi_done(sc_xfer);
}
static int
wdc_atapi_get_params(struct scsipi_channel *chan, int drive,
struct ataparams *id)
{
struct wdc_softc *wdc = device_private(chan->chan_adapter->adapt_dev);
struct atac_softc *atac = &wdc->sc_atac;
struct wdc_regs *wdr = &wdc->regs[chan->chan_channel];
struct ata_channel *chp = atac->atac_channels[chan->chan_channel];
struct ata_xfer *xfer;
int rv;
xfer = ata_get_xfer(chp, false);
if (xfer == NULL) {
printf("wdc_atapi_get_params: no xfer\n");
return EBUSY;
}
xfer->c_ata_c.r_command = ATAPI_SOFT_RESET;
xfer->c_ata_c.r_st_bmask = 0;
xfer->c_ata_c.r_st_pmask = 0;
xfer->c_ata_c.flags = AT_WAIT | AT_POLL;
xfer->c_ata_c.timeout = WDC_RESET_WAIT;
wdc_exec_command(&chp->ch_drive[drive], xfer);
ata_wait_cmd(chp, xfer);
if (xfer->c_ata_c.flags & (AT_ERROR | AT_TIMEOU | AT_DF)) {
ATADEBUG_PRINT(("wdc_atapi_get_params: ATAPI_SOFT_RESET "
"failed for drive %s:%d:%d: error 0x%x\n",
device_xname(atac->atac_dev), chp->ch_channel, drive,
xfer->c_ata_c.r_error), DEBUG_PROBE);
rv = -1;
goto out_xfer;
}
chp->ch_drive[drive].state = 0;
ata_free_xfer(chp, xfer);
(void)bus_space_read_1(wdr->cmd_iot, wdr->cmd_iohs[wd_status], 0);
/* Some ATAPI devices need a bit more time after software reset. */
delay(5000);
if (ata_get_params(&chp->ch_drive[drive], AT_WAIT, id) != 0) {
ATADEBUG_PRINT(("wdc_atapi_get_params: ATAPI_IDENTIFY_DEVICE "
"failed for drive %s:%d:%d\n",
device_xname(atac->atac_dev), chp->ch_channel, drive),
DEBUG_PROBE);
rv = -1;
goto out;
}
rv = 0;
out:
return rv;
out_xfer:
ata_free_xfer(chp, xfer);
return rv;
}
static void
wdc_atapi_probe_device(struct atapibus_softc *sc, int target)
{
struct scsipi_channel *chan = sc->sc_channel;
struct scsipi_periph *periph;
struct ataparams ids;
struct ataparams *id = &ids;
struct wdc_softc *wdc = device_private(chan->chan_adapter->adapt_dev);
struct atac_softc *atac = &wdc->sc_atac;
struct ata_channel *chp = atac->atac_channels[chan->chan_channel];
struct ata_drive_datas *drvp = &chp->ch_drive[target];
struct scsipibus_attach_args sa;
char serial_number[21], model[41], firmware_revision[9];
int s;
/* skip if already attached */
if (scsipi_lookup_periph(chan, target, 0) != NULL)
return;
/* if no ATAPI device detected at wdc attach time, skip */
if (drvp->drive_type != ATA_DRIVET_ATAPI) {
ATADEBUG_PRINT(("wdc_atapi_probe_device: "
"drive %d not present\n", target), DEBUG_PROBE);
return;
}
if (wdc_atapi_get_params(chan, target, id) == 0) {
#ifdef ATAPI_DEBUG_PROBE
printf("%s drive %d: cmdsz 0x%x drqtype 0x%x\n",
device_xname(sc->sc_dev), target,
id->atap_config & ATAPI_CFG_CMD_MASK,
id->atap_config & ATAPI_CFG_DRQ_MASK);
#endif
periph = scsipi_alloc_periph(M_WAITOK);
periph->periph_dev = NULL;
periph->periph_channel = chan;
periph->periph_switch = &atapi_probe_periphsw;
periph->periph_target = target;
periph->periph_lun = 0;
periph->periph_quirks = PQUIRK_ONLYBIG;
#ifdef SCSIPI_DEBUG
if (SCSIPI_DEBUG_TYPE == SCSIPI_BUSTYPE_ATAPI &&
SCSIPI_DEBUG_TARGET == target)
periph->periph_dbflags |= SCSIPI_DEBUG_FLAGS;
#endif
periph->periph_type = ATAPI_CFG_TYPE(id->atap_config);
if (id->atap_config & ATAPI_CFG_REMOV)
periph->periph_flags |= PERIPH_REMOVABLE;
if (periph->periph_type == T_SEQUENTIAL) {
s = splbio();
drvp->drive_flags |= ATA_DRIVE_ATAPIDSCW;
splx(s);
}
sa.sa_periph = periph;
sa.sa_inqbuf.type = ATAPI_CFG_TYPE(id->atap_config);
sa.sa_inqbuf.removable = id->atap_config & ATAPI_CFG_REMOV ?
T_REMOV : T_FIXED;
strnvisx(model, sizeof(model), id->atap_model,
sizeof(id->atap_model), VIS_TRIM|VIS_SAFE|VIS_OCTAL);
strnvisx(serial_number, sizeof(serial_number),
id->atap_serial, sizeof(id->atap_serial),
VIS_TRIM|VIS_SAFE|VIS_OCTAL);
strnvisx(firmware_revision, sizeof(firmware_revision),
id->atap_revision, sizeof(id->atap_revision),
VIS_TRIM|VIS_SAFE|VIS_OCTAL);
sa.sa_inqbuf.vendor = model;
sa.sa_inqbuf.product = serial_number;
sa.sa_inqbuf.revision = firmware_revision;
/*
* Determine the operating mode capabilities of the device.
*/
if ((id->atap_config & ATAPI_CFG_CMD_MASK) == ATAPI_CFG_CMD_16)
periph->periph_cap |= PERIPH_CAP_CMD16;
/* XXX This is gross. */
periph->periph_cap |= (id->atap_config & ATAPI_CFG_DRQ_MASK);
drvp->drv_softc = atapi_probe_device(sc, target, periph, &sa);
if (drvp->drv_softc)
ata_probe_caps(drvp);
else {
s = splbio();
drvp->drive_type = ATA_DRIVET_NONE;
splx(s);
}
} else {
s = splbio();
drvp->drive_type = ATA_DRIVET_NONE;
splx(s);
}
}
static const struct ata_xfer_ops wdc_atapi_xfer_ops = {
.c_start = wdc_atapi_start,
.c_intr = wdc_atapi_intr,
.c_poll = wdc_atapi_poll,
.c_abort = wdc_atapi_reset,
.c_kill_xfer = wdc_atapi_kill_xfer,
};
static void
wdc_atapi_scsipi_request(struct scsipi_channel *chan, scsipi_adapter_req_t req,
void *arg)
{
struct scsipi_adapter *adapt = chan->chan_adapter;
struct scsipi_periph *periph;
struct scsipi_xfer *sc_xfer;
struct wdc_softc *wdc = device_private(adapt->adapt_dev);
struct atac_softc *atac = &wdc->sc_atac;
struct ata_xfer *xfer;
int channel = chan->chan_channel;
int drive, s;
switch (req) {
case ADAPTER_REQ_RUN_XFER:
sc_xfer = arg;
periph = sc_xfer->xs_periph;
drive = periph->periph_target;
ATADEBUG_PRINT(("wdc_atapi_scsipi_request %s:%d:%d\n",
device_xname(atac->atac_dev), channel, drive),
DEBUG_XFERS);
if (!device_is_active(atac->atac_dev)) {
sc_xfer->error = XS_DRIVER_STUFFUP;
scsipi_done(sc_xfer);
return;
}
xfer = ata_get_xfer(atac->atac_channels[channel], false);
if (xfer == NULL) {
sc_xfer->error = XS_RESOURCE_SHORTAGE;
scsipi_done(sc_xfer);
return;
}
if (sc_xfer->xs_control & XS_CTL_POLL)
xfer->c_flags |= C_POLL;
#if NATA_DMA
if ((atac->atac_channels[channel]->ch_drive[drive].drive_flags &
(ATA_DRIVE_DMA | ATA_DRIVE_UDMA)) && sc_xfer->datalen > 0)
xfer->c_flags |= C_DMA;
#endif
#if NATA_DMA && NATA_PIOBM
else
#endif
#if NATA_PIOBM
if ((atac->atac_cap & ATAC_CAP_PIOBM) &&
sc_xfer->datalen > 0)
xfer->c_flags |= C_PIOBM;
#endif
xfer->c_drive = drive;
xfer->c_flags |= C_ATAPI;
#if NATA_DMA
if (sc_xfer->cmd->opcode == GPCMD_REPORT_KEY ||
sc_xfer->cmd->opcode == GPCMD_SEND_KEY ||
sc_xfer->cmd->opcode == GPCMD_READ_DVD_STRUCTURE) {
/*
* DVD authentication commands must always be done in
* PIO mode.
*/
xfer->c_flags &= ~C_DMA;
}
/*
* DMA normally can't deal with transfers which are not a
* multiple of its databus width. It's a bug to request odd
* length transfers for ATAPI.
*
* Some devices also can't cope with unaligned DMA xfers
* either. Also some devices seem to not handle DMA xfers of
* less than 4 bytes.
*
* By enforcing at least 4 byte aligned offset and length for
* DMA, we might use PIO where DMA could be allowed but better
* safe than sorry as recent problems proved.
*
* Offending structures that are thus done by PIO instead of
* DMA are normally small structures since all bulkdata is
* aligned. But as the request may come from userland, we have
* to protect against it anyway.
*
* XXX check for the 32 bit wide flag?
*/
if (((uintptr_t) sc_xfer->data) & 0x03)
xfer->c_flags &= ~C_DMA;
if ((sc_xfer->datalen < 4) || (sc_xfer->datalen & 0x03))
xfer->c_flags &= ~C_DMA;
#endif /* NATA_DMA */
xfer->c_databuf = sc_xfer->data;
xfer->c_bcount = sc_xfer->datalen;
xfer->ops = &wdc_atapi_xfer_ops;
xfer->c_scsipi = sc_xfer;
xfer->c_atapi.c_dscpoll = 0;
s = splbio();
ata_exec_xfer(atac->atac_channels[channel], xfer);
#ifdef DIAGNOSTIC
if ((sc_xfer->xs_control & XS_CTL_POLL) != 0 &&
(sc_xfer->xs_status & XS_STS_DONE) == 0)
panic("wdc_atapi_scsipi_request: polled command "
"not done");
#endif
splx(s);
return;
default:
/* Not supported, nothing to do. */
;
}
}
static int
wdc_atapi_start(struct ata_channel *chp, struct ata_xfer *xfer)
{
struct atac_softc *atac = chp->ch_atac;
struct wdc_softc *wdc = CHAN_TO_WDC(chp);
struct wdc_regs *wdr = &wdc->regs[chp->ch_channel];
struct scsipi_xfer *sc_xfer = xfer->c_scsipi;
struct ata_drive_datas *drvp = &chp->ch_drive[xfer->c_drive];
int wait_flags = (sc_xfer->xs_control & XS_CTL_POLL) ? AT_POLL : 0;
int tfd;
const char *errstring;
ATADEBUG_PRINT(("wdc_atapi_start %s:%d:%d, scsi flags 0x%x \n",
device_xname(atac->atac_dev), chp->ch_channel, drvp->drive,
sc_xfer->xs_control), DEBUG_XFERS);
ata_channel_lock_owned(chp);
#if NATA_DMA
if ((xfer->c_flags & C_DMA) && (drvp->n_xfers <= NXFER))
drvp->n_xfers++;
#endif
/* Do control operations specially. */
if (__predict_false(drvp->state < READY)) {
/* If it's not a polled command, we need the kernel thread */
if ((sc_xfer->xs_control & XS_CTL_POLL) == 0
&& !ata_is_thread_run(chp))
return ATASTART_TH;
/*
* disable interrupts, all commands here should be quick
* enough to be able to poll, and we don't go here that often
*/
bus_space_write_1(wdr->ctl_iot, wdr->ctl_ioh, wd_aux_ctlr,
WDCTL_4BIT | WDCTL_IDS);
if (wdc->select)
wdc->select(chp, xfer->c_drive);
bus_space_write_1(wdr->cmd_iot, wdr->cmd_iohs[wd_sdh], 0,
WDSD_IBM | (xfer->c_drive << 4));
/* Don't try to set mode if controller can't be adjusted */
if (atac->atac_set_modes == NULL)
goto ready;
/* Also don't try if the drive didn't report its mode */
if ((drvp->drive_flags & ATA_DRIVE_MODE) == 0)
goto ready;
errstring = "unbusy";
if (wdc_wait_for_unbusy(chp, ATAPI_DELAY, wait_flags, &tfd))
goto timeout;
wdccommand(chp, drvp->drive, SET_FEATURES, 0, 0, 0,
0x08 | drvp->PIO_mode, WDSF_SET_MODE);
errstring = "piomode";
if (wdc_wait_for_unbusy(chp, ATAPI_MODE_DELAY, wait_flags,
&tfd))
goto timeout;
if (ATACH_ST(tfd) & WDCS_ERR) {
if (ATACH_ST(tfd) == WDCE_ABRT) {
/*
* Some ATAPI drives reject PIO settings.
* Fall back to PIO mode 3 since that's the
* minimum for ATAPI.
*/
printf("%s:%d:%d: PIO mode %d rejected, "
"falling back to PIO mode 3\n",
device_xname(atac->atac_dev),
chp->ch_channel, xfer->c_drive,
drvp->PIO_mode);
if (drvp->PIO_mode > 3)
drvp->PIO_mode = 3;
} else
goto error;
}
#if NATA_DMA
#if NATA_UDMA
if (drvp->drive_flags & ATA_DRIVE_UDMA) {
wdccommand(chp, drvp->drive, SET_FEATURES, 0, 0, 0,
0x40 | drvp->UDMA_mode, WDSF_SET_MODE);
} else
#endif
if (drvp->drive_flags & ATA_DRIVE_DMA) {
wdccommand(chp, drvp->drive, SET_FEATURES, 0, 0, 0,
0x20 | drvp->DMA_mode, WDSF_SET_MODE);
} else {
goto ready;
}
errstring = "dmamode";
if (wdc_wait_for_unbusy(chp, ATAPI_MODE_DELAY, wait_flags,
&tfd))
goto timeout;
if (ATACH_ST(tfd) & WDCS_ERR) {
if (ATACH_ERR(tfd) == WDCE_ABRT) {
#if NATA_UDMA
if (drvp->drive_flags & ATA_DRIVE_UDMA)
goto error;
else
#endif
{
/*
* The drive rejected our DMA setting.
* Fall back to mode 1.
*/
printf("%s:%d:%d: DMA mode %d rejected, "
"falling back to DMA mode 0\n",
device_xname(atac->atac_dev),
chp->ch_channel, xfer->c_drive,
drvp->DMA_mode);
if (drvp->DMA_mode > 0)
drvp->DMA_mode = 0;
}
} else
goto error;
}
#endif /* NATA_DMA */
ready:
drvp->state = READY;
bus_space_write_1(wdr->ctl_iot, wdr->ctl_ioh, wd_aux_ctlr,
WDCTL_4BIT);
delay(10); /* some drives need a little delay here */
}
/* start timeout machinery */
if ((sc_xfer->xs_control & XS_CTL_POLL) == 0)
callout_reset(&chp->c_timo_callout, mstohz(sc_xfer->timeout),
wdctimeout, chp);
if (wdc->select)
wdc->select(chp, xfer->c_drive);
bus_space_write_1(wdr->cmd_iot, wdr->cmd_iohs[wd_sdh], 0,
WDSD_IBM | (xfer->c_drive << 4));
switch (wdc_wait_for_unbusy(chp, ATAPI_DELAY, wait_flags, &tfd)) {
case WDCWAIT_OK:
break;
case WDCWAIT_TOUT:
printf("wdc_atapi_start: not ready, st = %02x\n",
ATACH_ST(tfd));
sc_xfer->error = XS_TIMEOUT;
return ATASTART_ABORT;
case WDCWAIT_THR:
return ATASTART_TH;
}
/*
* Even with WDCS_ERR, the device should accept a command packet
* Limit length to what can be stuffed into the cylinder register
* (16 bits). Some CD-ROMs seem to interpret '0' as 65536,
* but not all devices do that and it's not obvious from the
* ATAPI spec that that behaviour should be expected. If more
* data is necessary, multiple data transfer phases will be done.
*/
wdccommand(chp, xfer->c_drive, ATAPI_PKT_CMD,
xfer->c_bcount <= 0xffff ? xfer->c_bcount : 0xffff,
0, 0, 0,
#if NATA_DMA
(xfer->c_flags & C_DMA) ? ATAPI_PKT_CMD_FTRE_DMA :
#endif
0
);
#if NATA_PIOBM
if (xfer->c_flags & C_PIOBM) {
int error;
int dma_flags = (sc_xfer->xs_control & XS_CTL_DATA_IN)
? WDC_DMA_READ : 0;
if (xfer->c_flags & C_POLL) {
/* XXX not supported yet --- fall back to PIO */
xfer->c_flags &= ~C_PIOBM;
} else {
/* Init the DMA channel. */
error = (*wdc->dma_init)(wdc->dma_arg,
chp->ch_channel, xfer->c_drive,
(char *)xfer->c_databuf,
xfer->c_bcount,
dma_flags | WDC_DMA_PIOBM_ATAPI);
if (error) {
if (error == EINVAL) {
/*
* We can't do DMA on this transfer
* for some reason. Fall back to
* PIO.
*/
xfer->c_flags &= ~C_PIOBM;
error = 0;
} else {
sc_xfer->error = XS_DRIVER_STUFFUP;
errstring = "piobm";
goto error;
}
}
}
}
#endif
/*
* If there is no interrupt for CMD input, busy-wait for it (done in
* the interrupt routine. Poll routine will exit early in this case.
*/
if ((sc_xfer->xs_periph->periph_cap & ATAPI_CFG_DRQ_MASK) !=
ATAPI_CFG_IRQ_DRQ || (sc_xfer->xs_control & XS_CTL_POLL))
return ATASTART_POLL;
else {
chp->ch_flags |= ATACH_IRQ_WAIT;
return ATASTART_STARTED;
}
timeout:
printf("%s:%d:%d: %s timed out\n",
device_xname(atac->atac_dev), chp->ch_channel, xfer->c_drive,
errstring);
sc_xfer->error = XS_TIMEOUT;
bus_space_write_1(wdr->ctl_iot, wdr->ctl_ioh, wd_aux_ctlr, WDCTL_4BIT);
delay(10); /* some drives need a little delay here */
return ATASTART_ABORT;
error:
printf("%s:%d:%d: %s ",
device_xname(atac->atac_dev), chp->ch_channel, xfer->c_drive,
errstring);
printf("error (0x%x)\n", ATACH_ERR(tfd));
sc_xfer->error = XS_SHORTSENSE;
sc_xfer->sense.atapi_sense = ATACH_ERR(tfd);
bus_space_write_1(wdr->ctl_iot, wdr->ctl_ioh, wd_aux_ctlr, WDCTL_4BIT);
delay(10); /* some drives need a little delay here */
return ATASTART_ABORT;
}
static int
wdc_atapi_poll(struct ata_channel *chp, struct ata_xfer *xfer)
{
/*
* If there is no interrupt for CMD input, busy-wait for it (done in
* the interrupt routine. If it is a polled command, call the interrupt
* routine until command is done.
*/
const bool poll = ((xfer->c_scsipi->xs_control & XS_CTL_POLL) != 0);
/* Wait for at last 400ns for status bit to be valid */
DELAY(1);
wdc_atapi_intr(chp, xfer, 0);
if (!poll)
return ATAPOLL_DONE;
#if NATA_DMA
if (chp->ch_flags & ATACH_DMA_WAIT) {
wdc_dmawait(chp, xfer, xfer->c_scsipi->timeout);
chp->ch_flags &= ~ATACH_DMA_WAIT;
}
#endif
while ((xfer->c_scsipi->xs_status & XS_STS_DONE) == 0) {
/* Wait for at last 400ns for status bit to be valid */
DELAY(1);
wdc_atapi_intr(chp, xfer, 0);
}
return ATAPOLL_DONE;
}
static int
wdc_atapi_intr(struct ata_channel *chp, struct ata_xfer *xfer, int irq)
{
struct atac_softc *atac = chp->ch_atac;
struct wdc_softc *wdc = CHAN_TO_WDC(chp);
struct wdc_regs *wdr = &wdc->regs[chp->ch_channel];
struct scsipi_xfer *sc_xfer = xfer->c_scsipi;
struct ata_drive_datas *drvp = &chp->ch_drive[xfer->c_drive];
int len, phase, i, retries=0;
int ire, tfd;
#if NATA_DMA
int error;
#endif
#if NATA_DMA || NATA_PIOBM
int dma_flags = 0;
#endif
void *cmd;
ATADEBUG_PRINT(("wdc_atapi_intr %s:%d:%d\n",
device_xname(atac->atac_dev), chp->ch_channel, drvp->drive),
DEBUG_INTR);
ata_channel_lock(chp);
/* Is it not a transfer, but a control operation? */
if (drvp->state < READY) {
printf("%s:%d:%d: bad state %d in wdc_atapi_intr\n",
device_xname(atac->atac_dev), chp->ch_channel,
xfer->c_drive, drvp->state);
panic("wdc_atapi_intr: bad state");
}
/*
* If we missed an interrupt in a PIO transfer, reset and restart.
* Don't try to continue transfer, we may have missed cycles.
*/
if ((xfer->c_flags & (C_TIMEOU | C_DMA)) == C_TIMEOU) {
ata_channel_unlock(chp);
sc_xfer->error = XS_TIMEOUT;
wdc_atapi_reset(chp, xfer);
return 1;
}
#if NATA_PIOBM
/* Transfer-done interrupt for busmastering PIO operation */
if ((xfer->c_flags & C_PIOBM) && (chp->ch_flags & ATACH_PIOBM_WAIT)) {
chp->ch_flags &= ~ATACH_PIOBM_WAIT;
/* restore transfer length */
len = xfer->c_bcount;
if (xfer->c_atapi.c_lenoff < 0)
len += xfer->c_atapi.c_lenoff;
if (sc_xfer->xs_control & XS_CTL_DATA_IN)
goto end_piobm_datain;
else
goto end_piobm_dataout;
}
#endif
/* Ack interrupt done in wdc_wait_for_unbusy */
if (wdc->select)
wdc->select(chp, xfer->c_drive);
bus_space_write_1(wdr->cmd_iot, wdr->cmd_iohs[wd_sdh], 0,
WDSD_IBM | (xfer->c_drive << 4));
if (wdc_wait_for_unbusy(chp,
(irq == 0) ? sc_xfer->timeout : 0, AT_POLL, &tfd) == WDCWAIT_TOUT) {
if (irq && (xfer->c_flags & C_TIMEOU) == 0) {
ata_channel_unlock(chp);
return 0; /* IRQ was not for us */
}
printf("%s:%d:%d: device timeout, c_bcount=%d, c_skip=%d\n",
device_xname(atac->atac_dev), chp->ch_channel,
xfer->c_drive, xfer->c_bcount, xfer->c_skip);
#if NATA_DMA
if (xfer->c_flags & C_DMA) {
ata_dmaerr(drvp,
(xfer->c_flags & C_POLL) ? AT_POLL : 0);
}
#endif
sc_xfer->error = XS_TIMEOUT;
ata_channel_unlock(chp);
wdc_atapi_reset(chp, xfer);
return 1;
}
if (wdc->irqack)
wdc->irqack(chp);
#if NATA_DMA
/*
* If we missed an IRQ and were using DMA, flag it as a DMA error
* and reset device.
*/
if ((xfer->c_flags & C_TIMEOU) && (xfer->c_flags & C_DMA)) {
ata_dmaerr(drvp, (xfer->c_flags & C_POLL) ? AT_POLL : 0);
sc_xfer->error = XS_RESET;
ata_channel_unlock(chp);
wdc_atapi_reset(chp, xfer);
return (1);
}
#endif
/*
* if the request sense command was aborted, report the short sense
* previously recorded, else continue normal processing
*/
#if NATA_DMA || NATA_PIOBM
if (xfer->c_flags & (C_DMA | C_PIOBM))
dma_flags = (sc_xfer->xs_control & XS_CTL_DATA_IN)
? WDC_DMA_READ : 0;
#endif
again:
len = bus_space_read_1(wdr->cmd_iot, wdr->cmd_iohs[wd_cyl_lo], 0) +
256 * bus_space_read_1(wdr->cmd_iot, wdr->cmd_iohs[wd_cyl_hi], 0);
ire = bus_space_read_1(wdr->cmd_iot, wdr->cmd_iohs[wd_ireason], 0);
phase = (ire & (WDCI_CMD | WDCI_IN)) | (ATACH_ST(tfd) & WDCS_DRQ);
ATADEBUG_PRINT(("wdc_atapi_intr: c_bcount %d len %d st 0x%x err 0x%x "
"ire 0x%x :", xfer->c_bcount,
len, ATACH_ST(tfd), ATACH_ERR(tfd), ire), DEBUG_INTR);
switch (phase) {
case PHASE_CMDOUT:
cmd = sc_xfer->cmd;
ATADEBUG_PRINT(("PHASE_CMDOUT\n"), DEBUG_INTR);
#if NATA_DMA
/* Init the DMA channel if necessary */
if (xfer->c_flags & C_DMA) {
error = (*wdc->dma_init)(wdc->dma_arg,
chp->ch_channel, xfer->c_drive,
xfer->c_databuf, xfer->c_bcount, dma_flags);
if (error) {
if (error == EINVAL) {
/*
* We can't do DMA on this transfer
* for some reason. Fall back to
* PIO.
*/
xfer->c_flags &= ~C_DMA;
error = 0;
} else {
sc_xfer->error = XS_DRIVER_STUFFUP;
break;
}
}
}
#endif
/* send packet command */
/* Commands are 12 or 16 bytes long. It's 32-bit aligned */
wdc->dataout_pio(chp, drvp->drive_flags, cmd, sc_xfer->cmdlen);
#if NATA_DMA
/* Start the DMA channel if necessary */
if (xfer->c_flags & C_DMA) {
(*wdc->dma_start)(wdc->dma_arg,
chp->ch_channel, xfer->c_drive);
chp->ch_flags |= ATACH_DMA_WAIT;
}
#endif
if ((sc_xfer->xs_control & XS_CTL_POLL) == 0) {
chp->ch_flags |= ATACH_IRQ_WAIT;
}
ata_channel_unlock(chp);
return 1;
case PHASE_DATAOUT:
/* write data */
ATADEBUG_PRINT(("PHASE_DATAOUT\n"), DEBUG_INTR);
#if NATA_DMA
if ((sc_xfer->xs_control & XS_CTL_DATA_OUT) == 0 ||
(xfer->c_flags & C_DMA) != 0) {
printf("wdc_atapi_intr: bad data phase DATAOUT\n");
if (xfer->c_flags & C_DMA) {
ata_dmaerr(drvp,
(xfer->c_flags & C_POLL) ? AT_POLL : 0);
}
sc_xfer->error = XS_TIMEOUT;
ata_channel_unlock(chp);
wdc_atapi_reset(chp, xfer);
return 1;
}
#endif
xfer->c_atapi.c_lenoff = len - xfer->c_bcount;
if (xfer->c_bcount < len) {
printf("wdc_atapi_intr: warning: write only "
"%d of %d requested bytes\n", xfer->c_bcount, len);
len = xfer->c_bcount;
}
#if NATA_PIOBM
if (xfer->c_flags & C_PIOBM) {
/* start the busmastering PIO */
(*wdc->piobm_start)(wdc->dma_arg,
chp->ch_channel, xfer->c_drive,
xfer->c_skip, len, WDC_PIOBM_XFER_IRQ);
chp->ch_flags |= ATACH_DMA_WAIT | ATACH_IRQ_WAIT |
ATACH_PIOBM_WAIT;
ata_channel_unlock(chp);
return 1;
}
#endif
wdc->dataout_pio(chp, drvp->drive_flags,
(char *)xfer->c_databuf + xfer->c_skip, len);
#if NATA_PIOBM
end_piobm_dataout:
#endif
for (i = xfer->c_atapi.c_lenoff; i > 0; i -= 2)
bus_space_write_2(wdr->cmd_iot,
wdr->cmd_iohs[wd_data], 0, 0);
xfer->c_skip += len;
xfer->c_bcount -= len;
if ((sc_xfer->xs_control & XS_CTL_POLL) == 0) {
chp->ch_flags |= ATACH_IRQ_WAIT;
}
ata_channel_unlock(chp);
return 1;
case PHASE_DATAIN:
/* Read data */
ATADEBUG_PRINT(("PHASE_DATAIN\n"), DEBUG_INTR);
#if NATA_DMA
if ((sc_xfer->xs_control & XS_CTL_DATA_IN) == 0 ||
(xfer->c_flags & C_DMA) != 0) {
printf("wdc_atapi_intr: bad data phase DATAIN\n");
if (xfer->c_flags & C_DMA) {
ata_dmaerr(drvp,
(xfer->c_flags & C_POLL) ? AT_POLL : 0);
}
sc_xfer->error = XS_TIMEOUT;
ata_channel_unlock(chp);
wdc_atapi_reset(chp, xfer);
return 1;
}
#endif
xfer->c_atapi.c_lenoff = len - xfer->c_bcount;
if (xfer->c_bcount < len) {
printf("wdc_atapi_intr: warning: reading only "
"%d of %d bytes\n", xfer->c_bcount, len);
len = xfer->c_bcount;
}
#if NATA_PIOBM
if (xfer->c_flags & C_PIOBM) {
/* start the busmastering PIO */
(*wdc->piobm_start)(wdc->dma_arg,
chp->ch_channel, xfer->c_drive,
xfer->c_skip, len, WDC_PIOBM_XFER_IRQ);
chp->ch_flags |= ATACH_DMA_WAIT | ATACH_IRQ_WAIT |
ATACH_PIOBM_WAIT;
ata_channel_unlock(chp);
return 1;
}
#endif
wdc->datain_pio(chp, drvp->drive_flags,
(char *)xfer->c_databuf + xfer->c_skip, len);
#if NATA_PIOBM
end_piobm_datain:
#endif
if (xfer->c_atapi.c_lenoff > 0)
wdcbit_bucket(chp, xfer->c_atapi.c_lenoff);
xfer->c_skip += len;
xfer->c_bcount -= len;
if ((sc_xfer->xs_control & XS_CTL_POLL) == 0) {
chp->ch_flags |= ATACH_IRQ_WAIT;
}
ata_channel_unlock(chp);
return 1;
case PHASE_ABORTED:
case PHASE_COMPLETED:
ATADEBUG_PRINT(("PHASE_COMPLETED\n"), DEBUG_INTR);
#if NATA_DMA
if (xfer->c_flags & C_DMA) {
xfer->c_bcount -= sc_xfer->datalen;
}
#endif
sc_xfer->resid = xfer->c_bcount;
/* this will unlock channel lock too */
wdc_atapi_phase_complete(xfer, tfd);
return(1);
default:
if (++retries<500) {
DELAY(100);
tfd = ATACH_ERR_ST(
bus_space_read_1(wdr->cmd_iot,
wdr->cmd_iohs[wd_error], 0),
bus_space_read_1(wdr->cmd_iot,
wdr->cmd_iohs[wd_status], 0)
);
goto again;
}
printf("wdc_atapi_intr: unknown phase 0x%x\n", phase);
if (ATACH_ST(tfd) & WDCS_ERR) {
sc_xfer->error = XS_SHORTSENSE;
sc_xfer->sense.atapi_sense = ATACH_ERR(tfd);
} else {
#if NATA_DMA
if (xfer->c_flags & C_DMA) {
ata_dmaerr(drvp,
(xfer->c_flags & C_POLL) ? AT_POLL : 0);
}
#endif
sc_xfer->error = XS_RESET;
ata_channel_unlock(chp);
wdc_atapi_reset(chp, xfer);
return (1);
}
}
ATADEBUG_PRINT(("wdc_atapi_intr: wdc_atapi_done() (end), error 0x%x "
"sense 0x%x\n", sc_xfer->error, sc_xfer->sense.atapi_sense),
DEBUG_INTR);
ata_channel_unlock(chp);
wdc_atapi_done(chp, xfer);
return (1);
}
static void
wdc_atapi_phase_complete(struct ata_xfer *xfer, int tfd)
{
struct ata_channel *chp = xfer->c_chp;
struct atac_softc *atac = chp->ch_atac;
#if NATA_DMA || NATA_PIOBM
struct wdc_softc *wdc = CHAN_TO_WDC(chp);
#endif
struct scsipi_xfer *sc_xfer = xfer->c_scsipi;
struct ata_drive_datas *drvp = &chp->ch_drive[xfer->c_drive];
ata_channel_lock_owned(chp);
/* wait for DSC if needed */
if (drvp->drive_flags & ATA_DRIVE_ATAPIDSCW) {
ATADEBUG_PRINT(("wdc_atapi_phase_complete(%s:%d:%d) "
"polldsc %d\n", device_xname(atac->atac_dev),
chp->ch_channel,
xfer->c_drive, xfer->c_atapi.c_dscpoll), DEBUG_XFERS);
#if 1
if (cold)
panic("wdc_atapi_phase_complete: cold");
#endif
if (wdcwait(chp, WDCS_DSC, WDCS_DSC, 10,
AT_POLL, &tfd) == WDCWAIT_TOUT) {
/* 10ms not enough, try again in 1 tick */
if (xfer->c_atapi.c_dscpoll++ >
mstohz(sc_xfer->timeout)) {
printf("%s:%d:%d: wait_for_dsc "
"failed\n",
device_xname(atac->atac_dev),
chp->ch_channel, xfer->c_drive);
ata_channel_unlock(chp);
sc_xfer->error = XS_TIMEOUT;
wdc_atapi_reset(chp, xfer);
} else {
callout_reset(&chp->c_timo_callout, 1,
wdc_atapi_polldsc, chp);
ata_channel_unlock(chp);
}
return;
}
}
/*
* Some drive occasionally set WDCS_ERR with
* "ATA illegal length indication" in the error
* register. If we read some data the sense is valid
* anyway, so don't report the error.
*/
if (ATACH_ST(tfd) & WDCS_ERR &&
((sc_xfer->xs_control & XS_CTL_REQSENSE) == 0 ||
sc_xfer->resid == sc_xfer->datalen)) {
/* save the short sense */
sc_xfer->error = XS_SHORTSENSE;
sc_xfer->sense.atapi_sense = ATACH_ERR(tfd);
if ((sc_xfer->xs_periph->periph_quirks &
PQUIRK_NOSENSE) == 0) {
/* ask scsipi to send a REQUEST_SENSE */
sc_xfer->error = XS_BUSY;
sc_xfer->status = SCSI_CHECK;
}
#if NATA_DMA || NATA_PIOBM
else if (wdc->dma_status &
(WDC_DMAST_NOIRQ | WDC_DMAST_ERR)) {
#if NATA_DMA
ata_dmaerr(drvp,
(xfer->c_flags & C_POLL) ? AT_POLL : 0);
#endif
sc_xfer->error = XS_RESET;
ata_channel_unlock(chp);
wdc_atapi_reset(chp, xfer);
return;
}
#endif
}
if (xfer->c_bcount != 0) {
ATADEBUG_PRINT(("wdc_atapi_intr: bcount value is "
"%d after io\n", xfer->c_bcount), DEBUG_XFERS);
}
#ifdef DIAGNOSTIC
if (xfer->c_bcount < 0) {
printf("wdc_atapi_intr warning: bcount value "
"is %d after io\n", xfer->c_bcount);
}
#endif
ATADEBUG_PRINT(("wdc_atapi_phase_complete: wdc_atapi_done(), "
"error 0x%x sense 0x%x\n", sc_xfer->error,
sc_xfer->sense.atapi_sense), DEBUG_INTR);
ata_channel_unlock(chp);
wdc_atapi_done(chp, xfer);
}
static void
wdc_atapi_done(struct ata_channel *chp, struct ata_xfer *xfer)
{
struct atac_softc *atac = chp->ch_atac;
struct scsipi_xfer *sc_xfer = xfer->c_scsipi;
ATADEBUG_PRINT(("wdc_atapi_done %s:%d:%d: flags 0x%x\n",
device_xname(atac->atac_dev), chp->ch_channel, xfer->c_drive,
(u_int)xfer->c_flags), DEBUG_XFERS);
if (ata_waitdrain_xfer_check(chp, xfer))
return;
ata_deactivate_xfer(chp, xfer);
ata_free_xfer(chp, xfer);
ATADEBUG_PRINT(("wdc_atapi_done: scsipi_done\n"), DEBUG_XFERS);
scsipi_done(sc_xfer);
ATADEBUG_PRINT(("atastart from wdc_atapi_done, flags 0x%x\n",
chp->ch_flags), DEBUG_XFERS);
atastart(chp);
}
static void
wdc_atapi_reset(struct ata_channel *chp, struct ata_xfer *xfer)
{
struct atac_softc *atac = chp->ch_atac;
struct ata_drive_datas *drvp = &chp->ch_drive[xfer->c_drive];
struct scsipi_xfer *sc_xfer = xfer->c_scsipi;
int tfd;
ata_channel_lock(chp);
wdccommandshort(chp, xfer->c_drive, ATAPI_SOFT_RESET);
drvp->state = 0;
if (wdc_wait_for_unbusy(chp, WDC_RESET_WAIT, AT_POLL, &tfd) != 0) {
printf("%s:%d:%d: reset failed\n",
device_xname(atac->atac_dev), chp->ch_channel,
xfer->c_drive);
sc_xfer->error = XS_SELTIMEOUT;
}
ata_channel_unlock(chp);
wdc_atapi_done(chp, xfer);
return;
}
static void
wdc_atapi_polldsc(void *arg)
{
struct ata_channel *chp = arg;
struct ata_xfer *xfer = ata_queue_get_active_xfer(chp);
KASSERT(xfer != NULL);
ata_channel_lock(chp);
/* this will unlock channel lock too */
wdc_atapi_phase_complete(xfer, 0);
}