/* $NetBSD: tsl256xreg.h,v 1.1 2018/05/27 05:31:20 thorpej Exp $ */
/*-
* Copyright (c) 2018 Jason R. Thorpe
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef tsl256xreg_h_included
#define tsl256xreg_h_included
/*
* Hardware definitions for the TAOS TSL2560 (SMBus) and TSL2561 (I2C).
*
* These devices combine a broadband photodiode (visible light + infrared)
* and an additional ifrared phtodiode onto a single CMOS integrated circuit.
* The devices include programmable thresholds that can trigger SMB-Alert
* type interrupts (TSL2560) or a traditional level-triggered interrupt
* (TSL2561) that remains asserted until cleared.
*/
/*
* Valid I2C addresses for the TSL2561. The address is selected based
* on how the ADDR_SEL pin is connected.
*/
#define TSL256x_SLAVEADDR_GND 0x29 /* ADDR SEL tied to ground */
#define TSL256x_SLAVEADDR_FLOAT 0x39 /* ADDR SEL left floating */
#define TSL256x_SLAVEADDR_VDD 0x49 /* ADDR SEL tied to Vdd */
#define TSL256x_SMB_ALERT_ADDR 0x0c /* SMB Alert address (all configs) */
/*
* TSL256x register definitions.
*/
/* COMMAND - Specifies register address and other parameters */
#define COMMAND_REGMASK 0x0f /* register address mask */
#define COMMAND_BLOCK 0x10 /* transaction uses block read/write */
#define COMMAND_WORD 0x20 /* transaction uses word read/write */
#define COMMAND_CLEAR 0x40 /* clear pending interrupt */
#define COMMAND_CMD 0x80 /* Select command register; MBO */
/* CONTROL - Control of basic functions */
#define TSL256x_REG_CONTROL 0x0
#define CONTROL_POWER_OFF 0x00
#define CONTROL_POWER_ON 0x03
/* TIMING - Integration time / gain control */
#define TSL256x_REG_TIMING 0x1
#define TIMING_INTEG_13_7ms 0x00 /* 13.7ms integration time */
#define TIMING_INTEG_101ms 0x01 /* 101ms integration time */
#define TIMING_INTEG_402ms 0x02 /* 402ms integration time */
#define TIMING_INTEG_MANUAL 0x03 /* use manual timing */
#define TIMING_MANUAL 0x08 /* manual timing; 1 starts, 0 stops */
#define TIMING_GAIN_1X 0x00
#define TIMING_GAIN_16X 0x10
/* THRESHLOWLOW - Low byte of low interrupt threshold */
#define TSL256x_REG_LOWLOW 0x2
/* THRESHLOWHIGH - High byte of low interrupt threshold */
#define TSL256x_REG_LOWHIGH 0x3
/* THRESHHIGHLOW - Low byte of high interrupt threshold */
#define TSL256x_REG_HIGHLOW 0x4
/* THRESHHIGHHIGH - High byte of high interrupt threshold */
#define TSL256x_REG_HIGHHIGH 0x5
/* INTERRUPT - Interrupt control */
#define TSL256x_REG_INTERRUPT 0x6
#define INTERRUPT_LEVEL 0x01 /* Level-triggered interrupt */
#define INTERRUPT_SMB_ALERT 0x02 /* SMB Alert compliant interrupt */
#define INTERRUPT_TEST 0x03 /* interrupt test */
#define INTERRUPT_PERSIST(x) ((x) << 4)
/*
* Interrupt persist settings:
* 0 - Every ADC cycle generates an interrupt
* 1..15 - # integration periods outside threshold range
*/
/* 0x7 - Reserved */
/* CRC - Factory test -- not a user register */
#define TSL256x_REG_CRC 0x8
/* 0x9 - Reserved */
/* ID - Part number / Rev ID */
#define TSL256x_REG_ID 0xa
#define ID_GET_PARTNO(x) (((x) & 0xf0) >> 4)
#define ID_PARTNO_TSL2560 0x0
#define ID_PARTNO_TSL2561 0x1
#define ID_GET_REVNO(x) ((x) & 0x0f)
/* 0xb - Reserved */
/* DATA0LOW - Low byte of ADC channel 0 */
#define TSL256x_REG_DATA0LOW 0xc
/* DATA0HIGH - High byte of ADC channel 0 */
#define TSL256x_REG_DATA0HIGH 0xd
/* DATA1LOW - Low byte of ADC channel 1 */
#define TSL256x_REG_DATA1LOW 0xe
/* DATA1HIGH - High byte of ADC channel 1 */
#define TSL256x_REG_DATA1HIGH 0xf
#endif /* tsl256xreg_h_included */