/*	$NetBSD: lan9118reg.h,v 1.3 2010/09/27 12:29:03 kiyohara Exp $	*/
/*
 * Copyright (c) 2008 KIYOHARA Takashi
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

#ifndef _LAN9118REG_H_
#define _LAN9118REG_H_

#define LAN9118_IOSIZE	0x100

#define LAN9118_ID_9115	0x0115
#define LAN9118_ID_9116	0x0116
#define LAN9118_ID_9117	0x0117
#define LAN9118_ID_9118	0x0118
#define LAN9218_ID_9215	0x115a
#define LAN9218_ID_9217	0x117a
#define LAN9218_ID_9218	0x118a

#define LAN9210_ID_9210	0x9210
#define LAN9210_ID_9211	0x9211
#define LAN9220_ID_9220	0x9220
#define LAN9220_ID_9221	0x9221

#define IS_LAN9118(id)	((id) >= LAN9118_ID_9115 && (id) <= LAN9118_ID_9118)
#define IS_LAN9218(id)	((id) >= LAN9218_ID_9215 && (id) <= LAN9218_ID_9218)

#define LAN9118_IPHY_ADDR	0x01	/* Internal PHY Address */


#define LAN9118_RXDFIFOP	0x00	/* RX Data FIFO Port */
#define LAN9118_RXDFIFOAP	0x04	/* RX Data FIFO Alias Ports */
#define LAN9118_TXDFIFOP	0x20	/* TX Data FIFO Port */
#define LAN9118_TXDFIFOAP	0x24	/* TX Data FIFO Alias Ports */
#define LAN9118_RXSFIFOP	0x40	/* RX Status FIFO Port */
#define LAN9118_RXSFIFOPEEK	0x44	/* RX Status FIFO PEEK */
#define LAN9118_TXSFIFOP	0x48	/* TX Status FIFO Port */
#define LAN9118_TXSFIFOPEEK	0x4c	/* TX Status FIFO PEEK */

/* System Control and Status Registers */
#define LAN9118_ID_REV		0x50	/* Chip ID and Revision */
#define LAN9118_ID_REV_ID(x)		(((x) >> 16) & 0xffff)
#define LAN9118_ID_REV_REV(x)		((x) & 0xffff)
#define LAN9118_IRQ_CFG		0x54	/* Main Interrupt Configuration */
#define LAN9118_IRQ_CFG_INT_DEAS(t)	((t) << 24) /* Intr Deassert Interval */
#define LAN9118_IRQ_CFG_INT_DEAS_CLR	(1 << 14)   /* Intr Deass Intrval clr */
#define LAN9118_IRQ_CFG_INT_DEAS_STS	(1 << 13)   /* Intr Deassert Status */
#define LAN9118_IRQ_CFG_IRQ_INT		(1 << 12)   /* Master Interrupt */
#define LAN9118_IRQ_CFG_IRQ_EN		(1 << 8)    /* IRQ Enable */
#define LAN9118_IRQ_CFG_IRQ_POL		(1 << 4)    /* IRQ Polarity */
#define LAN9118_IRQ_CFG_IRQ_TYPE	(1 << 0)    /* IRQ Buffer Type */
#define LAN9118_INT_STS		0x58	/* Interrupt Status */
#define LAN9118_INT_EN		0x5c	/* Interrupt Enable Register */
#define LAN9118_INT_SW_INT		(1 << 31) /* Software Interrupt */
#define LAN9118_INT_TXSTOP_INT		(1 << 25) /* TX Stopped */
#define LAN9118_INT_RXSTOP_INT		(1 << 24) /* RX Stopped */
#define LAN9118_INT_RXDFH_INT		(1 << 23) /* RX Drppd Frm Cnt Halfway */
#define LAN9118_INT_TX_IOC		(1 << 21) /* TX IOC Interrupt */
#define LAN9118_INT_RXD_INT		(1 << 20) /* RX DMA Interrupt */
#define LAN9118_INT_GPT_INT		(1 << 19) /* GP Timer */
#define LAN9118_INT_PHY_INT		(1 << 18) /* PHY */
#define LAN9118_INT_PME_INT		(1 << 17) /* Power Management Event */
#define LAN9118_INT_TXSO		(1 << 16) /* TX Status FIFO Overflow */
#define LAN9118_INT_RWT			(1 << 15) /* Rcv Watchdog Time-out */
#define LAN9118_INT_RXE			(1 << 14) /* Receive Error */
#define LAN9118_INT_TXE			(1 << 13) /* Transmitter Error */
#define LAN9118_INT_TDFO		(1 << 10) /* TX Data FIFO Overrun */
#define LAN9118_INT_TDFA		(1 << 9)  /* TX Data FIFO Available */
#define LAN9118_INT_TSFF		(1 << 8)  /* TX Status FIFO Full */
#define LAN9118_INT_TSFL		(1 << 7)  /* TX Status FIFO Level */
#define LAN9118_INT_RXDF_INT		(1 << 6)  /* RX Dropped Frame Intr */
#define LAN9118_INT_RSFF		(1 << 4)  /* RX Status FIFO Full */
#define LAN9118_INT_RSFL		(1 << 3)  /* RX Status FIFO Level */
#define LAN9118_INT_GPIOX_INT(x)	(1 << (x)) /* GPIO[2:0] */
/*				0x60	   Reserved for future use */
#define LAN9118_BYTE_TEST	0x64	/* Read-only byte order testing reg */
#define LAN9118_BYTE_TEST_VALUE		0x87654321
#define LAN9118_FIFO_INT	0x68	/* FIFO Level Interrupt */
#define LAN9118_FIFO_INT_TXDAL(x)	((x) << 24) /* TX Data Available Lvl */
#define LAN9118_FIFO_INT_TXSL(x)	((x) << 16) /* TX Status Level */
#define LAN9118_FIFO_INT_RXSL(x)	((x) << 0)  /* RX Status Level */
#define LAN9118_RX_CFG		0x6c	/* Receive Configuration */
#define LAN9118_RX_CFG_RXEA_4B		(0 << 30) /* RX End Alignment: 4 Byte */
#define LAN9118_RX_CFG_RXEA_16B		(1 << 30) /*                  16 Byte */
#define LAN9118_RX_CFG_RXEA_32B		(2 << 30) /*                  32 Byte */
#define LAN9118_RX_CFG_RX_DMA_CNT(x)	((x) << 16) /* RX DMA Count */
#define LAN9118_RX_CFG_RX_DUMP		(1 << 15)   /* Force RX Discard */
#define LAN9118_RX_CFG_RXDOFF(x)	((x) << 8)  /* RX Data Offset */
#define LAN9118_TX_CFG		0x70	/* Transmit Configuration */
#define LAN9118_TX_CFG_TXS_DUMP		(1 << 15) /* Force TX Status Discard */
#define LAN9118_TX_CFG_TXD_DUMP		(1 << 14) /* Force TX Data Discard */
#define LAN9118_TX_CFG_TXSAO		(1 << 2)  /* TX Status Allow Overrun */
#define LAN9118_TX_CFG_TX_ON		(1 << 1)  /* Transmitter Enable */
#define LAN9118_TX_CFG_STOP_TX		(1 << 0)  /* Stop Transmitter */
#define LAN9118_HW_CFG		0x74	/* Hardware Configuration */
#define LAN9118_HW_CFG_MBO		(1 << 20)/* Must Be One */
#define LAN9118_HW_CFG_TX_FIF_MASK	(0xf << 16)	/* TX FIFO Size */
#define LAN9118_HW_CFG_TX_FIF_SZ(sz)	((sz) << 16)
#define LAN9118_HW_CFG_PHY_CLK_SEL_MASK	(3 << 5) /* PHY Clock Select */
#define LAN9118_HW_CFG_PHY_CLK_SEL_IPHY	(0 << 5) /*   Internal PHY */
#define LAN9118_HW_CFG_PHY_CLK_SEL_EMII	(1 << 5) /*   External MII Port */
#define LAN9118_HW_CFG_PHY_CLK_SEL_CD	(2 << 5) /*   Clock Disabled */
#define LAN9118_HW_CFG_SMI_SEL		(1 << 4) /* Serial Mgmt Interface Sel */
#define LAN9118_HW_CFG_EXT_PHY_DET	(1 << 3) /* External PHY Detect */
#define LAN9118_HW_CFG_EXT_PHY_EN	(1 << 2) /* External PHY Enable */
#define LAN9118_HW_CFG_SRST_TO		(1 << 1) /* Soft Reset Timeout */
#define LAN9118_HW_CFG_SRST		(1 << 0) /* Soft Reset */
#define LAN9118_RX_DP_CTL	0x78	/* RX Datapath Control */
#define LAN9118_RX_DP_CTL_RX_FFWD	(1 << 31)/* RX Data FIFO Fast Forward */
#define LAN9118_RX_FIFO_INF	0x7c	/* Receive FIFO Information */
#define LAN9118_RX_FIFO_INF_RXSUSED(x)	(((x) >> 16) & 0xff) /*Sts Used Space*/
#define LAN9118_RX_FIFO_INF_RXDUSED(x)	((x) & 0xffff)	/*Data FIFO Used Space*/
#define LAN9118_TX_FIFO_INF	0x80	/* Transmit FIFO Information */
#define LAN9118_TX_FIFO_INF_TXSUSED(x)	(((x) >> 16) & 0xff) /*Sts Used Space*/
#define LAN9118_TX_FIFO_INF_TDFREE(x)	((x) & 0xffff) /*Data FIFO Free Space*/
#define LAN9118_PMT_CTRL	0x84	/* Power Management Control */
#define LAN9118_PMT_CTRL_PM_MODE_MASK	(3 << 12)
#define LAN9118_PMT_CTRL_PM_MODE_D0	(0 << 12)
#define LAN9118_PMT_CTRL_PM_MODE_D1	(1 << 12)
#define LAN9118_PMT_CTRL_PM_MODE_D2	(2 << 12)
#define LAN9118_PMT_CTRL_PHY_RST	(1 << 10) /* PHY Reset */
#define LAN9118_PMT_CTRL_WOL_EN		(1 << 9)  /* Wake-On-LAN Enable */
#define LAN9118_PMT_CTRL_ED_EN		(1 << 8)  /* Energy-Detect Enable */
#define LAN9118_PMT_CTRL_PME_TYPE	(1 << 6)  /* PME Buffer Type */
#define LAN9118_PMT_CTRL_WUPS_NWUED	(0 << 4) /* WAKE-UP Status: No Event */
#define LAN9118_PMT_CTRL_WUPS_ED	(1 << 4) /* WAKE-UP Status: Energy */
#define LAN9118_PMT_CTRL_WUPS_WUD	(2 << 4) /* WAKE-UP Status: Wake-up */
#define LAN9118_PMT_CTRL_PME_IND	(1 << 3)  /* PME indication */
#define LAN9118_PMT_CTRL_PME_POL	(1 << 2)  /* PME Polarity */
#define LAN9118_PMT_CTRL_PME_EN		(1 << 1)  /* PME Enable */
#define LAN9118_PMT_CTRL_READY		(1 << 0)  /* Device Ready */
#define LAN9118_GPIO_CFG	0x88	/* General Purpose IO Configuration */
#define LAN9118_GPIO_CFG_LEDX_EN(x)	(1 << ((x) + 28))  /* LED[3:1] enable */
#define LAN9118_GPIO_CFG_GPIO_INT_POL(p) (1 << ((p) + 24)) /* Intr Polarity */
#define LAN9118_GPIO_CFG_EEPR_EN	(7 << 20)          /* EEPROM Enable */
#define LAN9118_GPIO_CFG_GPIOBUFN(n)	(1 << ((n) + 16))  /* Buffer Type */
#define LAN9118_GPIO_CFG_GPDIRN(n)	(1 << ((n) + 8))   /* Direction */
#define LAN9118_GPIO_CFG_GPODN(n)	(1 << (n)) /* GPIO Data (3,4 is WO) */
#define LAN9118_GPT_CFG		0x8c	/* General Purpose Timer Config */
#define LAN9118_GPT_CNT		0x90	/* General Purpose Timer Count */
/*				0x94	   Reserved for future use */
#define LAN9118_WORD_SWAP	0x98	/* WORD SWAP Register */
#define LAN9118_FREE_RUN	0x9c	/* Free Run Counter */
#define LAN9118_RX_DROP		0xa0	/* RX Drop Frame Counter */
#define LAN9118_MAC_CSR_CMD	0xa4	/* MAC CSR Synchronizer Command */
#define LAN9118_MAC_CSR_CMD_BUSY	(1 << 31)
#define LAN9118_MAC_CSR_CMD_W		(0 << 30)
#define LAN9118_MAC_CSR_CMD_R		(1 << 30)
#define LAN9118_MAC_CSR_CMD_ADDRESS(a)	((a) & 0xff)
#define LAN9118_MAC_CSR_DATA	0xa8	/* MAC CSR Synchronizer Data */
#define LAN9118_AFC_CFG		0xac	/* Automatic Flow Control Config */
#define LAN9118_AFC_CFG_AFC_HI(x)	((x) << 16)
#define LAN9118_AFC_CFG_AFC_LO(x)	((x) << 8)
#define LAN9118_AFC_CFG_BACK_DUR(x)	((x) << 4)
#define LAN9118_AFC_CFG_FCMULT		(1 << 3) /* Flow Control on Multicast */
#define LAN9118_AFC_CFG_FCBRD		(1 << 2) /* Flow Control on Broadcast */
#define LAN9118_AFC_CFG_FCADD		(1 << 1) /* Flow Control on Addr Dec */
#define LAN9118_AFC_CFG_FCANY		(1 << 0) /* Flow Control on Any Frame */
#define LAN9118_E2P_CMD		0xb0	/* EEPROM command */
#define LAN9118_E2P_CMD_EPCB		(1 << 31) /* EPC Busy */
#define LAN9118_E2P_CMD_EPCC_READ	(0 << 28) /* EPC Command: READ */
#define LAN9118_E2P_CMD_EPCC_EWDS	(1 << 28) /*              EWDS */
#define LAN9118_E2P_CMD_EPCC_EWEN	(2 << 28) /*              EWEN */
#define LAN9118_E2P_CMD_EPCC_WRITE	(3 << 28) /*              WRITE */
#define LAN9118_E2P_CMD_EPCC_WRAL	(4 << 28) /*              WRAL */
#define LAN9118_E2P_CMD_EPCC_ERASE	(5 << 28) /*              ERASE */
#define LAN9118_E2P_CMD_EPCC_ERAL	(6 << 28) /*              ERAL */
#define LAN9118_E2P_CMD_EPCC_RELOAD	(7 << 28) /*              Reload */
#define LAN9118_E2P_CMD_EPCTO		(1 << 9)  /* EPC Time-out */
#define LAN9118_E2P_CMD_MACAL		(1 << 8)  /* MAC Address Loaded */
#define LAN9118_E2P_CMD_EPCA(a)		((a) & 0xff) /* EPC Address */
#define LAN9118_E2P_DATA	0xb4	/* EEPROM Data */
/*				0xb8 - 0xfc Reserved for future use */

/* MAC Control and Status Registers */
#define LAN9118_MAC_CR		0x1	/* MAC Control Register */
#define LAN9118_MAC_CR_RXALL		(1 << 31) /* Receive All Mode */
#define LAN9118_MAC_CR_RCVOWN		(1 << 23) /* Disable Receive Own */
#define LAN9118_MAC_CR_LOOPBK		(1 << 21) /* Loopback operation Mode */
#define LAN9118_MAC_CR_FDPX		(1 << 20) /* Full Duplex Mode */
#define LAN9118_MAC_CR_MCPAS		(1 << 19) /* Pass All Multicast */
#define LAN9118_MAC_CR_PRMS		(1 << 18) /* Promiscuous Mode */
#define LAN9118_MAC_CR_INVFILT		(1 << 17) /* Inverse filtering */
#define LAN9118_MAC_CR_PASSBAD		(1 << 16) /* Pass Bad Frames */
#define LAN9118_MAC_CR_HO		(1 << 15) /* Hash Only Filtering mode */
#define LAN9118_MAC_CR_HPFILT		(1 << 13) /* Hash/Perfect Flt Mode */
#define LAN9118_MAC_CR_LCOLL		(1 << 12) /* Late Collision Control */
#define LAN9118_MAC_CR_BCAST		(1 << 11) /* Disable Broardcast Frms */
#define LAN9118_MAC_CR_DISRTY		(1 << 10) /* Disable Retry */
#define LAN9118_MAC_CR_PADSTR		(1 << 8)  /* Automatic Pad String */
#define LAN9118_MAC_CR_BOLMT		(1 << 7)  /* BackOff Limit */
#define LAN9118_MAC_CR_DFCHK		(1 << 5)  /* Deferral Check */
#define LAN9118_MAC_CR_TXEN		(1 << 3)  /* Transmitter enable */
#define LAN9118_MAC_CR_RXEN		(1 << 2)  /* Receiver enable */
#define LAN9118_ADDRH		0x2	/* MAC Address High */
#define LAN9118_ADDRL		0x3	/* MAC Address Low */
#define LAN9118_HASHH		0x4	/* Multicast Hash Table High */
#define LAN9118_HASHL		0x5	/* Multicast Hash Table Low */
#define LAN9118_MII_ACC		0x6	/* MII Access */
#define LAN9118_MII_ACC_PHYA(a)		((a) << 11)	/* PHY Address */
#define LAN9118_MII_ACC_MIIRINDA(i)	((i) << 6)	/* MII Register Index */
#define LAN9118_MII_ACC_MIIWNR		(1 << 1)	/* MII Write */
#define LAN9118_MII_ACC_MIIBZY		(1 << 0)	/* MII Busy */
#define LAN9118_MII_DATA	0x7	/* MII Data */
#define LAN9118_FLOW		0x8	/* Flow Control */
#define LAN9118_FLOW_FCPT(t)		((t) << 16) /* Pause Time */
#define LAN9118_FLOW_FCPASS		(1 << 2)    /* Pass Control Frame */
#define LAN9118_FLOW_FCEN		(1 << 1)    /* Flow Control Enable */
#define LAN9118_FLOW_FCBUSY		(1 << 0)    /* Flow Control Busy */
#define LAN9118_VLAN1		0x9	/* VLAN1 Tag */
#define LAN9118_VLAN2		0xa	/* VLAN2 Tag */
#define LAN9118_WUFF		0xb	/* Wake-up Frame Filter */
#define LAN9118_WUCSR		0xc	/* Wake-up Control and Status */

/* PHY Registers */
#define LAN9118_MCSR		0x11	/* Mode Control/Status Register */
#define LAN9118_MCSR_EDPWRDOWN		(1 << 13) /* Energy Detect Power Down */
#define LAN9118_MCSR_ENERGYON		(1 << 1)
#define LAN9118_SMR		0x12	/* Special Modes Register */
#define LAN9118_SMR_PHYAD		(0x01)
#define LAN9118_SCSI		0x1b	/* Special Control/Status Indications */
#define LAN9118_SCSI_VCOOFF_LP		(1 << 10)
#define LAN9118_SCSI_XPOL		(1 << 4)  /* Polarity state */
#define LAN9118_ISR		0x1d	/* Interrupt Source Register */
#define LAN9118_IMR		0x1e	/* Interrupt Mask Register */
#define LAN9118_I_ENERGYON		(1 << 7)
#define LAN9118_I_AUTONEGOCOMPL		(1 << 6)
#define LAN9118_I_REMOTEFAULT		(1 << 5)
#define LAN9118_I_LINKDOWN		(1 << 4)
#define LAN9118_I_AUTONEGOLPACK		(1 << 3) /* AutoNego LP Acknowledge */
#define LAN9118_I_PDF			(1 << 2) /* Parallel Detection Fault */
#define LAN9118_I_AUTONEGOPR		(1 << 1) /* AutoNego Page Received */
#define LAN9118_PHYSCSR		0x1f	/* PHY Special Control/Status Reg */
#define LAN9118_PHYSCSR_AUTODONE	(1 << 12) /* AutoNego done indication */
#define LAN9118_PHYSCSR_SI_10		(1 << 2)  /* Speed Indication */
#define LAN9118_PHYSCSR_SI_100		(2 << 2)
#define LAN9118_PHYSCSR_SI_FDX		(4 << 2)


/* TX Command 'A' Format */
#define LAN9118_TXC_A_IC		(1 << 31) /* Interrupt on Completion */
#define LAN9118_TXC_A_BEA_4B		(0 << 24) /* Buffer End Alignment: 4B */
#define LAN9118_TXC_A_BEA_16B		(1 << 24) /*                      16B */
#define LAN9118_TXC_A_BEA_32B		(2 << 24) /*                      32B */
#define LAN9118_TXC_A_DSO(x)		((x) << 16) /*Data Start Offset: bytes*/
#define LAN9118_TXC_A_FS		(1 << 13) /* First Segment */
#define LAN9118_TXC_A_LS		(1 << 12) /* Last Segment */
#define LAN9118_TXC_A_BS(x)		((x) << 0) /* Buffer Size */

/* TX Command 'B' Format */
#define LAN9118_TXC_B_PT(x)		((x) << 16) /* Packet Tag */
#define LAN9118_TXC_B_ACRCD		(1 << 13)  /* Add CRC Disable */
#define LAN9118_TXC_B_DEFP		(1 << 12)  /* Dis Ether Frame Padding */
#define LAN9118_TXC_B_PL(x)		((x) << 0) /* Packet Length */

/* TX Status Format */
#define LAN9118_TXS_PKTTAG(x)		(((x) >> 16) & 0xff) /* Packet Tag */
#define LAN9118_TXS_ES			(1 << 15)	/* Error Status */
#define LAN9118_TXS_LOC			(1 << 11)	/* Loss Of Carrier */
#define LAN9118_TXS_NC			(1 << 10)	/* No Carrier */
#define LAN9118_TXS_LCOL		(1 << 9)	/* Late Collision */
#define LAN9118_TXS_ECOL		(1 << 8)	/* Excessive Collision*/
#define LAN9118_TXS_COLCNT(x)		(((x) >> 3) & 0xf) /* Collision Count */
#define LAN9118_TXS_ED			(1 << 2)	/* Excessive Deferral */
#define LAN9118_TXS_DEFERRED		(1 << 0)	/* Deferred */

/* RX Status Format */
#define LAN9118_RXS_FILTFAIL		(1 << 30) /* Filtering Fail */
#define LAN9118_RXS_PKTLEN(x)		(((x) >> 16) & 0x3fff) /* Packet Len */
#define LAN9118_RXS_ES			(1 << 15) /* Error Status */
#define LAN9118_RXS_BCF			(1 << 13) /* Broadcast Frame */
#define LAN9118_RXS_LENERR		(1 << 12) /* Length Error */
#define LAN9118_RXS_RUNTF		(1 << 11) /* Runt Frame */
#define LAN9118_RXS_MCF			(1 << 10) /* Multicast Frame */
#define LAN9118_RXS_FTL			(1 << 7)  /* Frame Too Long */
#define LAN9118_RXS_COLS		(1 << 6)  /* Collision Seen */
#define LAN9118_RXS_FT			(1 << 5)  /* Frame Type */
#define LAN9118_RXS_RWTO		(1 << 4)  /* Rcv Watchdog time-out */
#define LAN9118_RXS_MIIERR		(1 << 3)  /* MII Error */
#define LAN9118_RXS_DBIT		(1 << 2)  /* Drabbling Bit */
#define LAN9118_RXS_CRCERR		(1 << 1)  /* CRC Error */

#endif	/* _LAN9118REG_H_ */