/* $NetBSD: if_cuereg.h,v 1.22.2.1 2019/09/01 13:00:37 martin Exp $ */
/*
* Copyright (c) 1997, 1998, 1999, 2000
* Bill Paul <wpaul@ee.columbia.edu>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*
* $FreeBSD: src/sys/dev/usb/if_cuereg.h,v 1.3 2000/01/16 22:45:06 wpaul Exp $
*/
/*
* Definitions for the CATC Netmate II USB to ethernet controller.
*/
#include <sys/rndsource.h>
/*
* Vendor specific control commands.
*/
#define CUE_CMD_READSRAM 0xF1
#define CUE_CMD_GET_MACADDR 0xF2
#define CUE_CMD_RESET 0xF4
#define CUE_CMD_WRITEREG 0xFA
#define CUE_CMD_READREG 0xFB
#define CUE_CMD_WRITESRAM 0xFC
/*
* Internal registers
*/
#define CUE_TX_BUFCNT 0x20
#define CUE_RX_BUFCNT 0x21
#define CUE_ADVANCED_OPMODES 0x22
#define CUE_TX_BUFPKTS 0x23
#define CUE_RX_BUFPKTS 0x24
#define CUE_RX_MAXCHAIN 0x25
#define CUE_ETHCTL 0x60
#define CUE_ETHSTS 0x61
#define CUE_PAR5 0x62
#define CUE_PAR4 0x63
#define CUE_PAR3 0x64
#define CUE_PAR2 0x65
#define CUE_PAR1 0x66
#define CUE_PAR0 0x67
/* Error counters, all 16 bits wide. */
#define CUE_TX_SINGLECOLL 0x69
#define CUE_TX_MULTICOLL 0x6B
#define CUE_TX_EXCESSCOLL 0x6D
#define CUE_RX_FRAMEERR 0x6F
#define CUE_LEDCTL 0x81
/* Advenced operating mode register */
#define CUE_AOP_SRAMWAITS 0x03
#define CUE_AOP_EMBED_RXLEN 0x08
#define CUE_AOP_RXCOMBINE 0x10
#define CUE_AOP_TXCOMBINE 0x20
#define CUE_AOP_EVEN_PKT_READS 0x40
#define CUE_AOP_LOOPBK 0x80
/* Ethernet control register */
#define CUE_ETHCTL_RX_ON 0x01
#define CUE_ETHCTL_LINK_POLARITY 0x02
#define CUE_ETHCTL_LINK_FORCE_OK 0x04
#define CUE_ETHCTL_MCAST_ON 0x08
#define CUE_ETHCTL_PROMISC 0x10
/* Ethernet status register */
#define CUE_ETHSTS_NO_CARRIER 0x01
#define CUE_ETHSTS_LATECOLL 0x02
#define CUE_ETHSTS_EXCESSCOLL 0x04
#define CUE_ETHSTS_TXBUF_AVAIL 0x08
#define CUE_ETHSTS_BAD_POLARITY 0x10
#define CUE_ETHSTS_LINK_OK 0x20
/* LED control register */
#define CUE_LEDCTL_BLINK_1X 0x00
#define CUE_LEDCTL_BLINK_2X 0x01
#define CUE_LEDCTL_BLINK_QUARTER_ON 0x02
#define CUE_LEDCTL_BLINK_QUARTER_OFF 0x03
#define CUE_LEDCTL_OFF 0x04
#define CUE_LEDCTL_FOLLOW_LINK 0x08
/*
* Address in ASIC's internal SRAM where the
* multicast hash table lives. The table is 64 bytes long,
* giving us a 512-bit table. We have to set the bit that
* corresponds to the broadcast address in order to enable
* reception of broadcast frames.
*/
#define CUE_MCAST_TABLE_ADDR 0xFA80
#define CUE_MCAST_TABLE_LEN 64
#define CUE_CTL_READ 0x01
#define CUE_CTL_WRITE 0x02