Training courses

Kernel and Embedded Linux

Bootlin training courses

Embedded Linux, kernel,
Yocto Project, Buildroot, real-time,
graphics, boot time, debugging...

Bootlin logo

Elixir Cross Referencer

/*
 * Copyright (c) 2002-2008 Sam Leffler, Errno Consulting
 * Copyright (c) 2002-2008 Atheros Communications, Inc.
 *
 * Permission to use, copy, modify, and/or distribute this software for any
 * purpose with or without fee is hereby granted, provided that the above
 * copyright notice and this permission notice appear in all copies.
 *
 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
 *
 * $Id: ar5312reg.h,v 1.1.1.1 2008/12/11 04:46:46 alc Exp $
 */
#ifndef _DEV_ATH_AR5312REG_H_
#define _DEV_ATH_AR5312REG_H_

#include "ar5212/ar5212reg.h"
/*
 * Definitions for the Atheros 5312 chipset.
 */

/* Register base addresses for modules which are not wmac modules */
/* 531X has a fixed memory map */


#define REG_WRITE(_reg,_val)		*((volatile uint32_t *)(_reg)) = (_val);
#define REG_READ(_reg)		*((volatile uint32_t *)(_reg))
/* 
 * PCI-MAC Configuration registers (AR2315+)
 */
#define AR5315_RSTIMER_BASE 0xb1000000  /* Address for reset/timer registers */
#define AR5315_GPIO_BASE    0xb1000000  /* Address for GPIO registers */
#define AR5315_WLAN0            0xb0000000

#define AR5315_RESET   0x0004      /* Offset of reset control register */
#define AR5315_SREV    0x0014      /* Offset of reset control register */
#define AR5315_ENDIAN_CTL  0x000c  /* offset of the endian control register */
#define AR5315_CONFIG_WLAN     0x00000002      /* WLAN byteswap */

#define AR5315_REV_MAJ                     0x00f0
#define AR5315_REV_MIN                     0x000f

#define AR5315_GPIODIR      0x0098      /* GPIO direction register */
#define AR5315_GPIODO       0x0090      /* GPIO data output access reg */
#define AR5315_GPIODI       0x0088      /* GPIO data input access reg*/
#define AR5315_GPIOINT      0x00a0      /* GPIO interrupt control */

#define AR5315_GPIODIR_M(x) (1 << (x))  /* mask for i/o */
#define AR5315_GPIODIR_O(x) (1 << (x))  /* output */
#define AR5315_GPIODIR_I(x) 0           /* input */

#define AR5315_GPIOINT_S    0
#define AR5315_GPIOINT_M    0x3F
#define AR5315_GPIOINTLVL_S 6
#define AR5315_GPIOINTLVL_M (3 << AR5315_GPIOINTLVL_S)

#define AR5315_WREV         (-0xefbfe0)      /* Revision ID register offset */
#define AR5315_WREV_S       0           /* Shift for WMAC revision info */
#define AR5315_WREV_ID      0x000000FF  /* Mask for WMAC revision info */
#define AR5315_WREV_ID_S    4           /* Shift for WMAC Rev ID */
#define AR5315_WREV_REVISION 0x0000000F /* Mask for WMAN Revsion version */

#define AR5315_RC_BB0_CRES   0x00000002  /* Cold reset to WMAC0 & WBB0 */
#define AR5315_RC_BB1_CRES   0x00000200  /* Cold reset to WMAC1 & WBB1n */
#define AR5315_RC_WMAC0_RES  0x00000001  /* Warm reset to WMAC 0 */
#define AR5315_RC_WBB0_RES  0x00000002  /* Warm reset to WBB0 */
#define AR5315_RC_WMAC1_RES  0x00020000  /* Warm reset to WMAC1 */
#define AR5315_RC_WBB1_RES   0x00040000  /* Warm reset to WBB */

/*
 * PCI-MAC Configuration registers (AR5312)
 */
#define AR5312_RSTIMER_BASE 0xbc003000  /* Address for reset/timer registers */
#define AR5312_GPIO_BASE    0xbc002000  /* Address for GPIO registers */
#define AR5312_WLAN0            0xb8000000
#define AR5312_WLAN1            0xb8500000

#define AR5312_RESET	0x0020      /* Offset of reset control register */
#define	AR5312_PCICFG	0x00B0	    /* MAC/PCI configuration reg (LEDs) */

#define AR5312_PCICFG_LEDMODE  0x0000001c	/* LED Mode mask */
#define AR5312_PCICFG_LEDMODE_S  2	/* LED Mode shift */
#define AR5312_PCICFG_LEDMOD0  0	/* Blnk prop to Tx and filtered Rx */
#define AR5312_PCICFG_LEDMOD1  1	/* Blnk prop to all Tx and Rx */
#define AR5312_PCICFG_LEDMOD2  2	/* DEBG flash */
#define AR5312_PCICFG_LEDMOD3  3	/* BLNK Randomly */

#define	AR5312_PCICFG_LEDSEL   0x000000e0 /* LED Throughput select */
#define AR5312_PCICFG_LEDSEL_S 5
#define AR5312_PCICFG_LEDSEL0  0	/* See blink rate table on p. 143 */
#define AR5312_PCICFG_LEDSEL1  1	/* of AR5212 data sheet */
#define AR5312_PCICFG_LEDSEL2  2
#define AR5312_PCICFG_LEDSEL3  3
#define AR5312_PCICFG_LEDSEL4  4
#define AR5312_PCICFG_LEDSEL5  5
#define AR5312_PCICFG_LEDSEL6  6
#define AR5312_PCICFG_LEDSEL7  7

#define AR5312_PCICFG_LEDSBR   0x00000100 /* Slow blink rate if no
			   		     activity. 0 = blink @ lowest
					     rate */

#undef AR_GPIOCR
#undef AR_GPIODO                    /* Undefine the 5212 defs */
#undef AR_GPIODI

#define AR5312_GPIOCR       0x0008      /* GPIO Control register */
#define AR5312_GPIODO       0x0000      /* GPIO data output access reg */
#define AR5312_GPIODI       0x0004      /* GPIO data input access reg*/
/* NB: AR5312 uses AR5212 defines for GPIOCR definitions */

#define AR5312_WREV         0x0090      /* Revision ID register offset */
#define AR5312_WREV_S       8           /* Shift for WMAC revision info */
#define AR5312_WREV_ID      0x000000FF  /* Mask for WMAC revision info */
#define AR5312_WREV_ID_S    4           /* Shift for WMAC Rev ID */
#define AR5312_WREV_REVISION 0x0000000F /* Mask for WMAN Revsion version */

#define AR5312_RC_BB0_CRES   0x00000004  /* Cold reset to WMAC0 & WBB0 */
#define AR5312_RC_BB1_CRES   0x00000200  /* Cold reset to WMAC1 & WBB1n */
#define AR5312_RC_WMAC0_RES  0x00002000  /* Warm reset to WMAC 0 */
#define AR5312_RC_WBB0_RES  0x00004000  /* Warm reset to WBB0 */
#define AR5312_RC_WMAC1_RES  0x00020000  /* Warm reset to WMAC1 */
#define AR5312_RC_WBB1_RES   0x00040000  /* Warm reset to WBB */


#define AR_RAD2112_SREV_MAJOR   0x40    /* 2112 Major Rev */

enum AR5312PowerMode {
    AR5312_POWER_MODE_FORCE_SLEEP  = 0,
    AR5312_POWER_MODE_FORCE_WAKE   = 1,
    AR5312_POWER_MODE_NORMAL       = 2,
};

#endif /* _DEV_AR5312REG_H_ */